Jet JSM-606 Service manual

Operating Instructions and Parts Manual
Mini Belt Sanders
Models JSM-606/610/612/620/630
WALTER MEIER (Manufacturing) Inc.
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-JSM-630
Ph.: 800-274-6848 Revision G 07/2013
www.waltermeier.com Copyright © 2013 Walter Meier (Manufacturing) Inc.

2
Warranty and Service
Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of
our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any
of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or
perform routine maintenance and major repair on your JET® tools. For the name of an Authorized Service Center in
your area call 1-800-274-6848.
MORE INFORMATION
Walter Meier is consistently adding new products to the line. For complete, up-to-date product information, check with
your local Walter Meier distributor, or visit jettools.com.
WARRANTY
JET products carry a limited warranty which varies in duration based upon the product (MW = Metalworking, WW =
Woodworking).
WHAT IS COVERED?
This warranty covers any defects in workmanship or materials subject to the exceptions stated below. Cutting tools,
abrasives and other consumables are excluded from warranty coverage.
WHO IS COVERED?
This warranty covers only the initial purchaser of the product.
WHAT IS THE PERIOD OF COVERAGE?
The general JET warranty lasts for the time period specified in the product literature of each product.
WHAT IS NOT COVERED?
Five Year Warranties do not cover woodworking (WW) products used for commercial, industrial or educational
purposes. Woodworking products with Five Year Warranties that are used for commercial, industrial or education
purposes revert to a One Year Warranty. This warranty does not cover defects due directly or indirectly to misuse,
abuse, negligence or accidents, normal wear-and-tear, improper repair or alterations, or lack of maintenance.
HOW TO GET SERVICE
The product or part must be returned for examination, postage prepaid, to a location designated by us. For the name
of the location nearest you, please call 1-800-274-6848.
You must provide proof of initial purchase date and an explanation of the complaint must accompany the
merchandise. If our inspection discloses a defect, we will repair or replace the product, or refund the purchase price,
at our option. We will return the repaired product or replacement at our expense unless it is determined by us that
there is no defect, or that the defect resulted from causes not within the scope of our warranty in which case we will,
at your direction, dispose of or return the product. In the event you choose to have the product returned, you will be
responsible for the shipping and handling costs of the return.
HOW STATE LAW APPLIES
This warranty gives you specific legal rights; you may also have other rights which vary from state to state.
LIMITATIONS ON THIS WARRANTY
WALTER MEIER (MANUFACTURING) INC., LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE
LIMITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR
MERCHANTABILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG THE IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
WALTER MEIER SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR
FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF
OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
Walter Meier sells through distributors only. The specifications in Walter Meier catalogs are given as general
information and are not binding. Members of Walter Meier reserve the right to effect at any time, without prior notice,
those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason
whatsoever. JET® branded products are not sold in Canada by Walter Meier.

3
Table of contents
Section Page
Warranty and Service............................................................................................................................................2
Table of contents...................................................................................................................................................3
Specifications........................................................................................................................................................4
Operating conditions .............................................................................................................................................4
Before operation....................................................................................................................................................4
Tracking adjustment..............................................................................................................................................5
Belt replacement ...................................................................................................................................................5
Shoe Replacement................................................................................................................................................6
Idle pulley replacement .........................................................................................................................................6
Bracket replacement.............................................................................................................................................7
Storage..................................................................................................................................................................7
Speed adjustment .................................................................................................................................................7
Replacement Parts................................................................................................................................................7
JSM-606 Mini Belt Sander.................................................................................................................................8
JSM-610 Mini Belt Sander.................................................................................................................................9
JSM-612 Mini Belt Sander...............................................................................................................................10
JSM-620 Mini Belt Sander...............................................................................................................................11
JSM-630 Mini Belt Sander...............................................................................................................................12
Safety warnings
1. Read and understand the entire contents of this manual before attempting operation.
2. Never operate a belt sander without proper eye and face protection.
3. Do not operate sander while wearing gloves, loose clothing, jewelry or anything that may get caught in a
rotating belt. Long hair must be contained.
4. Wear ear protectors (plugs or muffs) during extended periods of operation.
5. Do not operate sander over 100 PSI.
6. Do not operate sander without the silencer (muffler) installed.
7. Keep hands and fingers away from sanding belt.
8. Disconnect sander from air source before making repairs, adjustments or belt changes.
9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain
chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
•Lead from lead based paint.
•Crystalline silica from bricks, cement and other masonry products.
•Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face
or dust masks that are specifically designed to filter out microscopic particles.
10. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for
which it was not designed. The right tool will do the job better and more safely.
11. Use recommended accessories; improper accessories may be hazardous.
12. Don’t use in dangerous environment. Don’t use power tools in damp or wet location, or expose them to
rain. Keep work area well lighted.
13. Failure to comply with all of the above warnings may lead to serious injury.

4
Specifications
Model/Stock number............... JSM-606...........JSM-610 ............JSM-612................JSM-620 .................JSM-630
Repair kit number ................... RPK-606...........RPK-610............RPK-612................RPK-620................. RPK-630
Rebuild kit number.................. RBK-606...........RBK-610............RBK-612................RBK-620.................RBK-630
Free speed (RPM)......................20,000..............20,000................20,000................... 18,000.....................12,000
Surface feet per minute (SFPM).....4328.................4328 .................. 4328......................9274 ........................6059
Belt size (in.)...........................1/4" x 13”.......... 3/8” x 13” ............1/2" x 24”......... 3/4" x 20-1/4” ......1-3/16” x 21-1/4”
Horsepower (HP)............................0.37..................0.37................... 0.37.......................0.45.......................... 0.7
Noise level (dB)................................ 80.....................80 ......................80..........................82 ........................... 79
Air pressure (psi).............................. 90.....................90 ......................90..........................90 ........................... 90
Air consumption (CFM)...................14.2..................14.2................... 14.2.......................18.4...........................24
Air inlet (NPT/in.) ............................. 1/4....................1/4..................... 1/4.........................1/4.......................... 1/4
Air hose (I.D./in.).............................. 3/8....................3/8..................... 3/8.........................3/8.......................... 3/8
Length folded (in.)...................... 10-7/8”..............10-7/8”.....................12”...................11-3/8” ....................11-5/8”
Maximum length open (in.)......... 15-3/4”..............15-3/4” .....................21”.........................19”................ 19-19/64”
Vibration value (m/s2)....................... 3.8....................3.8..................... 3.8.........................3.1.......................... 3.1
Height (in.)............................... 1-63/64”............1-63/64”.............1-63/64”.................2-23/64”.................... 4-9/64”
Net weight (lb).................................... 2.......................2 ........................2......................3-1/4....................... 4-1/2
Shipping weight (lb)............................ 3.......................3 ........................3............................4 ............................. 6
The specifications in this manual were current at time of publication, but because of our policy of continuous
improvement, Walter Meier (Manufacturing) Inc., reserves the right to change specifications at any time and without
prior notice, without incurring obligations.
Operating conditions
1. Compressor must be able to deliver 14.2 CFM,
70-100 PSI, and be rated at 3HP minimum for
models JSM-606/610/612. Models JSM-
620/630 require a compressor delivering 18-24
CFM rated at 5HP minimum.
2. Use 3/8” air hose between the compressor and
the sander.
3. To avoid moisture damage to the sander, use
an inline filter to trap moisture and an inline
oiler to keep the sander running at top
efficiency. These are placed inline between the
compressor and the sander. See Figure 1.
For further information, see “Air Tools – Instruction
and Care” enclosed with the sander.
Figure 1
Before operation
Disconnect sander from air
hose before making any repair or adjustment.
Failure to comply may cause serious injury.
1. Run compressor and blow out hose before
connecting sander to clear line of any
contaminants.
2. Before connecting the hose to the sander, add
4 to 5 drops of air tool oil to the air inlet.
3. If an inline oiler is not used, add 4 to 5 drops at
the air inlet for every three to four hours of
operation.
4. Adjust head to desired angle and tighten hex
socket cap screw (A, Figure 2), with hex
wrench supplied.
Always tighten hex socket
cap screw firmly after adjustment, or the
head could rotate causing loss of control.

5
Figure 2
Tracking adjustment
Tracking adjustment requires
the sander to be connected to the hose and
running. Use caution when hands and tools are
close to a running belt. Failure to comply may
cause serious injury.
Belt is tracking properly on all models when
centered on the idle pulley.
JSM-606: no adjustment
JSM-610/612:
1. Loosen set screw with wrench. See Figure 3.
2. With belt running, turn adjusting screw
clockwise or counterclockwise until it is
centered on the idler pulley.
3. Tighten set screw.
Figure 3
JSM-620/630:
Insert hex wrench into hex socket cap screw and
turn clockwise or counterclockwise until belt is
centered on idle pulley. See Figure 4.
Figure 4
Belt replacement
JSM-606/610:
1. Disconnect sander from air source.
2. Loosen hex cap screw (A, Figure 2), turn head
90-degrees to the handle, and tighten screw to
lock. See Figure 5.
3. Steady the sander with one hand while
pushing down on the idle wheel assembly with
the other until assembly locks in place. See
Figure 5.
4. Remove old belt. Install new belt.
5. Press safety lever (A, Figure 5) to tension belt.
Figure 5
JSM-612:
1. Disconnect sander from air source.
2. Loosen hex cap screw (A, Figure 2), turn head
90-degrees to the handle, and tighten screw to
lock. See Figure 6.
3. Steady sander with one hand while pushing
down on the idle pulley assembly and
removing belt with the other.
4. Install new belt over idle pulley.
5. Push idle pulley assembly down and place belt
on drive pulley. See sequence in Figure 6.

6
Figure 6
JSM-620/630:
1. Disconnect sander from air source.
2. Loosen hex cap screw (A, Figure 2), turn head
90-degrees to the handle, and tighten screw to
lock.
3. Grab handle with the left hand. Push down on
the idle pulley assembly and turn 1/8 of a full
turn clockwise to lock in place. See sequence
in Figure 7.
4. Remove old belt. Install new belt.
5. Push down and turn idle pulley assembly
counterclockwise to tension belt.
Figure 7
Shoe Replacement
The shoe or sanding platen should be replaced
when, due to wear, it no longer sits flat but is
convex in shape.
JSM-606/610/612:
1. Disconnect sander from air source.
2. Remove belt (see section titled “Belt
Replacement”).
3. Remove screw(s) and remove old shoe.
4. Install new shoe and fasten with screw(s).
Make sure insert on shoe end engages slot on
sander body.
JSM-620:
1. Disconnect sander from air source.
2. Remove belt (see section titled “Belt
Replacement”).
3. Loosen hex socket cap screw (A, Figure 8).
4. Remove old shoe. Replace with new shoe.
5. Tighten screw (A) and replace belt.
Figure 8
JSM-630:
1. Disconnect sander from air source.
2. Remove belt (see section titled “Belt
Replacement”).
3. Turn shoe holder (A, Figure 9) a quarter of a
turn with screwdriver to release shoe.
4. Insert new shoe and turn shoe holder to lock
new shoe. Replace belt.
Figure 9
Idle pulley replacement
Disconnect sander from air
hose before making any repair or adjustment.
Failure to comply may cause serious injury.
Follow diagram in Figure 10 for your sander model
when replacing the idle pulley.

7
Figure 10
Bracket replacement
JSM-606/610/612
1. Disconnect sander from air source.
2. Remove belt.
3. Pull out bracket in direction labeled A, Figure
11. Be careful not to lose spring.
Figure 11
4. Insert new bracket by lining up pin with pin
groove. See Figure 12.
Figure 12
Storage
1. Avoid storing sander in locations with high
humidity.
2. Before storing, apply four to five drops of air
tool oil at the air inlet and run for a short time.
Speed adjustment
All models have a brass screw used for belt speed
adjustment found on the underside of the handle.
This has been set at the factory. It is highly
recommended that the end user not attempt any
adjustment to the speed control.
Replacement Parts
Replacement parts are listed on the following
pages. To order parts or reach our service
department, call 1-800-274-6848 Monday through
Friday (see our website for business hours,
www.jettools.com). Having the Model Number and
Serial Number of your machine available when you
call will allow us to serve you quickly and
accurately.

8
JSM-606 Mini Belt Sander
Index Part No. Description Qty.
1 60601NPN Housing 1
2 60602NPN Guard Subassembly (w/60626) 1
3 60603NPN Air Inlet 1
4 60604NPN Lever 1
5 60605NPN Valve Stem 1
6 60606NPN Adjust Valve 1
7 60607NPN O-Ring 1
8 60608NPN Spring 1
9 60609NPN O-Ring 1
10 60610NPN Spacer 1
11 60611NPN Retaining Ring 1
12 60612NPN Spacer 1
13 BB-607ZZ Ball Bearing 1
14 60614NPN Rear End Plate 1
15 60615NPN Rotor 1
16 60616NPN Vane 4
17 60617NPN Sunk Key 1
18 60618NPN Cylinder 1
19 60619NPN Front End Plate 1
20 BB-628ZZ Ball Bearing 1
21 60621NPN Cap 1
22 60622NPN Drive Pulley 1
23 60623NPN Hexagon Nut 1
Index Part No. Description Qty.
24 60624NPN Shoe 1
25 60625NPN Hexagon Socket Head Bolt 1
26 60626NPN Dust Cover 1
27 60627NPN Nipple 1
28 60628NPN Spring 1
29 62029NPN Silencer 1
30 60630NPN Cross-Recessed Pan Hd Mach Screw 1
31 60631NPN Lever Support 1
32 60632NPN Cross-Recessed Pan Hd Mach Screw 3
33 60633NPN Spring Washer 2
34 60634NPN Hexagon Nut 1
35 60635NPN Grinding Belt 1
36 60636NPN Lock Pin 1
37 60637NPN Cross-Recessed Flat Hd Mach Screw 1
38 BB-684ZZ Ball Bearing 1
39 60639NPN Idle Pulley Shaft 1
40 60640NPN Spring 1
41 60641NPN Tension Bar 1
42 60642NPN Bushing 1
43 60643NPN Idle Pulley 1
44 60644NPN Spring Pin ø2.5x8L 1
45 60645NPN Spring 1
46 60646NPN Safety Lever 1
RPK-606 Repair Kit (contains #7,9,11,16,26)
RBK-606 Rebuild Kit (contains #37,38,39,41,43)
21
13
14
15
16
18
12
19
20
4
30 31
27
28
29
39
25
44
35
46
24
23 5
7
8
6
9
10
11
26
32
34
32
33
17
36
3
45
40
42
41
1
22
2
37
43
38

9
JSM-610 Mini Belt Sander
Index Part No. Description Qty.
1 61001 Housing 1
2 61002 Guard Body 1
61002A Guard Subassembly (w/61026)
3 61003 Air Inlet 1
4 61004 Lever 1
5 61005 Valve Stem 1
6 61006 Adjust Valve 1
7 61007 O-Ring 1
8 61008 Spring 1
9 61009 O-Ring 1
10 61010 Spacer 1
11 61011 Retaining Ring 1
12 61012 Spacer 1
13 61013 Ball Bearing 1
14 61014 Rear End Plate 1
15 61015 Rotor 1
16 61016 Vane 4
17 61017 Sunk Key 1
18 61018 Cylinder 1
19 61019 Front End Plate 1
20 61020 Ball Bearing 1
21 61021 Cap 1
22 61022 Drive Pulley 1
23 61023 Hexagon Nut 1
24 61024 Shoe 1
25 61025 Hexagon Socket Head Bolt 1
26 61026 Dust Cover 1
Index Part No. Description Qty.
27 61027 Nipple 1
28 61028 Spring 1
29 61029 Silencer 1
30 61030 Cross-Recessed Pan Hd Mach Screw 1
31 61031 Lever Support 1
32 61032 Cross-Recessed Pan Hd Mach Screw 3
33 61033 Spring Washer 2
34 61034 Hexagon Nut 1
35 61035 Cross-Recessed Pan Hd Mach Screw 1
36 61036 Spring Pin 1
37 61037 Cross-Recessed Pan Hd Mach Screw 1
38 61038 Ball Bearing 2
39 61039 Idle Pulley Shaft 1
40 61040 Spring 1
41 61041 Tension Bar 1
42 61042 Bushing 1
43 61043 Idle Pulley 1
44 61044 Spring 1
45 61045 Bracket 1
46 61046 Hexagon Soc Headless Set Screw 1
47 61047 Grinding Belt 1
48 61048 Spring Pin ø2.5 x 8L 1
49 61049 Spring 1
50 61050 Safety Lever 1
51 61051 Lock Pin ø3 x 11.8L 1
RPK-610 Repair Kit (contains #7,9,11,16,26)
RBK-610 Rebuild Kit (contains #35,36,37,38,39,43,44,45,46)
21
13
14
15
16
18
12
19
20
4
30 31
27
28
29
38
43
38
37
3946
35
25
48
47
50
24
23 5
7
8
6
9
10
11
26
32
34
32
33
17
51
36
44
3
49
40
42
41
45
1
22
2

10
JSM-612 Mini Belt Sander
Index Part No. Description Qty.
1 61201 Housing 1
2 61202 Guard Subassembly (w/61226) 1
3 61203 Air Inlet 1
4 61204 Lever 1
5 61205 Valve Stem 1
6 61206 Adjust Valve 1
7 61207 O-Ring 1
8 61208 Spring 1
9 61209 O-Ring 1
10 61210 Spacer 1
11 61211 Retaining Ring 1
12 61212 Spacer 1
13 61213 Ball Bearing 1
14 61214 Rear End Plate 1
15 61215 Rotor 1
16 61016 Vane 4
17 61217 Sunk Key 1
18 61218 Cylinder 1
19 61219 Front End Plate 1
20 61220 Ball Bearing 1
21 61221 Cap 1
22 61222 Drive Pulley 1
23 61223 Hexagon Nut 1
24 61224 Shoe 1
25 61225 Hexagon Socket Head Bolt 1
Index Part No. Description Qty.
26 61226 Dust Cover 1
27 61227 Nipple 1
28 61228 Spring 1
29 61229 Silencer 1
30 61230 Cross-Recessed Pan Hd Mach Screw 1
31 61231 Lever Support 1
32 61232 Cross-Recessed Pan Hd Mach Screw 4
33 61233 Spring Washer 2
34 61234 Hexagon Nut 1
35 61235 Cross-Recessed Pan Hd Mach Screw 1
36 61236 Spring Pin 1
37 61237 Cross-Recessed Pan Hd Mach Screw 1
38 61238 Ball Bearing 2
39 61239 Idle Pulley Shaft 1
40 61240 Spring 1
41 61241 Tension Bar 1
42 61242 Bushing 1
43 61243 Idle Pulley 1
44 61244 Spring 1
45 61245 Bracket 1
46 61246 Hexagon Soc Headless Set Screw 1
47 61247 Extension Bar 1
48 61248 Spacer 1
49 61249 Lock Pin ø3 x 9.8L 1
50 61250 Grinding Belt 1
RPK-612 Repair Kit (contains #7,9,16,26)
RBK-612 Rebuild Kit (contains #35,36,37,38,39,43,44,45,46,48,49)
21
13
14
15
16
18
12
19
20
4
30 31
27
28
29
38
43
38
37
3946
35
25
50
24
23 5
7
8
6
9
10
11
26
32
34
32
33
17
49
36
44
3
42
41
45
1
22
2
32
48
40
47

11
JSM-620 Mini Belt Sander
Index Part No. Description Qty.
1 62001NPN Housing 1
2 62002A Guard SubAssy w/62026NPN 1
3 62003NPN Air Inlet 1
4 62004NPN Lever 1
5 62005NPN Valve Stem 1
6 62006NPN Adjust Valve 1
7 62007NPN O-Ring 1
8 62008NPN Spring 1
9 62009NPN O-Ring 1
10 62010NPN Spacer 1
11 62011NPN Retaining Ring 1
12 62012NPN Spacer 1
13 BB-608ZZ Ball Bearing 1
14 62014NPN Rear End Plate 1
15 62015NPN Rotor 1
16 62016NPN Vane (4 pcs/set) 4
17 62017NPN Sunk Key 1
18 62018NPN Cylinder 1
19 62019NPN Front End Plate 1
20 BB-6000ZZ Ball Bearing 1
21 62021NPN Cap 1
22 62022NPN Drive Pulley 1
23 62023NPN Hexagon Nut 1
24 62024NPN Shoe 1
25 62025NPN Hexagon Socket Head Bolt 2
26 62026NPN Dust Cover 1
Index Part No. Description Qty.
27 62027NPN Nipple 1
28 62028NPN Spring 1
29 62029NPN Silencer 1
30 62030NPN Cross-Recessed Pan Hd Mach Screw 1
31 62031NPN Lever Support 1
32 62032NPN Cross-Recessed Pan Hd Mach Screw 1
33 62033 Spring Washer 1
34 62034 Hexagon Nut 1
35 62035 Bushing 1
36 62036 Finger Pad 1
37 62037 Washer 1
38 62038 Spring Washer 2
39 62039 Screw 1
40 62040 Spring 1
41 62041 Arm 1
42 62042 Nut 1
43 62043 Idle Pulley 1
44 62044 Shaft 1
45 62045 Ball Bearing 2
46 62046 Spacer 1
47 62047 Retaining Ring 1
48 62048 Bolt 1
49 62049 Bolt 1
50 62050 Spacer 1
51 62051NPN Grinding Belt 1
RPK-620 Repair Kit (contains #7,9,11,16,26)
RBK-620 Rebuild Kit (contains #42,43,44,45,46,47,50)
21
11
36
37
39
38
14
13
18
15
17
16
12
19
20
3
10
9
5
7
8
6
25
26
1
31
34
30
33
32
4
2
49
22
23
51
35
25
40
24
41
42
46
45
43
50
45
44
38
48
47
27
28
29

12
JSM-630 Mini Belt Sander
Index Part No. Description Qty.
1 63001 Housing 1
2 63002A Guard Subassembly w/63026 1
3 63003 Air Inlet 1
4 63004 Lever 1
5 63005 Valve Stem 1
6 63006 Adjust Valve 1
7 63007 Seal 1
8 63008 Spring 1
9 63009 O-Ring 1
10 63010 Spacer 1
11 63011 Retaining Ring 1
12 63012 Spacer 1
13 63013 Ball Bearing 2
14 63014 Rear End Plate 1
15 63015 Rotor 1
16 63016 Vane (5 pcs/set) 5
17 63017 Sunk Key 1
18 63018 Cylinder 1
19 63019 Front End Plate 1
20 63020 Ball Bearing 1
21 63021 Cap 1
22 63022 Drive Pulley 1
23 63023 Hexagon Nut 1
24 63024 Flat Shoe 1
25 63025 Hexagon Socket Head Bolt 1
26 63026 Dust Cover 1
27 63027 Nipple 1
28 63028 Spring 1
29 63029 Silencer 1
30 63030 Cross-Recessed Pan Hd Mach Screw 1
31 63031 Lever Support 1
32 63032 Cross-Recessed Pan Hd Mach Screw 2
33 63033 Spring Washer 2
Index Part No. Description Qty.
34 63034 Hexagon Nut 1
35 63035 Shoe Holder 1
36 63036 O-Ring 2
37 63037 Washer 1
38 63038 Spring Washer 1
39 63039 Screw 1
40 63040 Tension Spring 1
41 63041 Tension Bar 1
42 63042 Nut 1
43 63043 Idle Pulley 1
44 63044 Shaft 1
45 63045 Ball Bearing 2
46 63046 Spacer 1
47 63047 Retaining Ring 1
48 63048 Bolt 1
49 63049 Spring Washer 1
50 63050 Spring Pin 1
51 63051 Spacer 1
52 63052 Spring Retainer A 1
53 63053 Spring Retainer B 1
54 63054 Hexagon Soc Hd Bolt 1
55 63055 Sub Handle Holder 1
56 63056NPN Sub Handle Assembly 1
57 63057NPN Waved Lock Washer 1
58 63058 Thrust Washer 1
59 63059 Retaining Ring 1
60 63060 Thrust Washer 1
61 63061 Arm 1
62 63062NPN Spring Pin 1
63 63063NPN Retaining Ring 1
64 63064NPN Grinding Belt 1
RPK-630 Repair Kit (contains #7,9,11,16,26,36,52,53,60)
RBK-630 Rebuild Kit (contains #42,43,44,45,46,47,50,51)
29
3
28
27
6
9
10
11
5
7
20
63
8
18
14
13
21
15
17
16
12
62
19
13
4
32
33
31 34
30
35
36
36 1
60
2
25
26
57
58
59
22
23
64
37
38
39
24
43
40
52
55
54
41
61
50
48
49
42
47
46
45
43
51
45
44
56