Summer Essex Craft 33200 User manual

Essex Craft™ Safety Gate
USER MANUAL
Please read the following instructions carefully.
Keep this instruction manual and
save for future reference.
For technical support, contact us at 1-401-671-6551
or www.summerinfant.com/contact
Tools required: Phillips-head screwdriver,
measuring tape (not included),
and wrench (included).
For use with children from 6 - 24 months.
Keep small parts away from children.
Adult assembly required.
Fits openings from 28" - 42" wide.
33200

components
Gate Door
Left Gate Frame
A
B
Right Gate Frame
C
D
I
E
F
G
H
Tension Bolts with Tension Nuts (4)
Wall Cups (4)
Wall Anchors (4)
Screws (4)
Wrench
Adhesive Mounting Pads (4)
2
hardware
E
x4
I
D
x4
x1
H
F
G
x4
x4
BC
A
Children have died or been seriously injured when gates are not securely installed.
• ALWAYS install and use gate as directed using all required parts.
• Install according to manufacturer’s instructions.
• Stop using when a child can climb over or dislodge the gate.
• Use only with the locking/latching mechanism securely engaged.
• To prevent falls, never use at top of stairs without wall mounting cups and door stopper.
• NEVER use a gate to keep child away from pool.
• NEVER leave child unattended.
• ALWAYS close and lock the gate behind you.
• This product will not necessarily prevent all accidents. Proper adult supervision is required at all times.
• Do not use if any components are missing or damaged.
• Adult assembly required. Exercise care when unpacking and assembling product.
CAUTION: KEEP SMALL PARTS OUT OF CHILD’S REACH.
WARNING
x4
NOTE: Gate will appear as though door is o-center when taken
out of the package until you mount it into the doorframe and tighten the
bolts according to the instructions.

Door stop
gate configurations (choose which best fits your scenario)
3
Measure the width of the opening where you intend to install the gate.
Refer to the following illustrations to determine the correct installation
conguration. Baseboard molding may change which conguration is
appropriate.
A B
CD
(28"- 31.25") without extension frames (32"- 35.25") with small extension frame
(34.75"- 38") with large extension frame (38.75"- 42") with small & large extension frames
NEVER install two extension
frames on the same side of the
gate.
WARNING
Important: Gate includes a door stop
which prevents the gate from swinging
open in one direction. When installing
the gate at the top of stairs, be sure that
the door stop is used so the door cannot
open over the stairs.
!
Note: This instruction book illustrates
installation of gate conguration D.
If choosing gate conguration A, skip
ahead to step 2. Otherwise, follow step 1
using the appropriate extension frames
that best t your scenario.
!

4
installation
2
E
x 4
1
x 4
!
• If choosing gate conguration A, skip this step.
• If choosing gate conguration B or C, add the desired extension frame to either side of the gate frame.
• If choosing gate conguration D, add both extensions to the gate frame.
Slide tension bolts into
upper and lower holes on
both sides of extension
frames (or into the gate
frame if no extensions are
being used).
Connect the extension
frames to gate frame
by inserting extension
pins into the holes.

AB
installation (continued)
Check distances A & B. The distance
between the gate and the wall should
never exceed 2.75 in.
IMPORTANT
3
5
A. Stand the gate in the center of the
opening. Make sure the bottom of the gate is
completely flush to the floor.
B. Slide tension bolts out until they contact
the door frame or wall on both sides.

installation (continued)
4
5
6
Use the tension nuts to
tighten both of the bottom
tension bolts.
Use the tension nuts to
tighten both of the top
tension bolts.
tighten!
tighten!
tighten!
tighten!

2
1
STOP! wall cup/top of stairs installation
WARNING
For use at top of stairs, wall cup
installation is MANDATORY.
Follow these wall cup installation instructions when using gate at TOP OF STAIRS
(MANDATORY), or if using wall cups for a standard opening (optional). If opting not to
use wall cups for a standard opening, skip ahead to step 9.
With a pencil, trace the
entire outline of each
tension bolt directly
onto the wall.
Loosen the lower
and upper
tension nuts and
remove gate.
7
x 4
loosen!
x 2
loosen!
x 2
At the top of the
landing, position the
gate a minimum of
3-6 inches (8-15cm)
away from the top
step.
IMPORTANT

3
Note: If mounting directly
into wood, skip this step.
!
x 4
x4
wall cup/top of stairs installation (continued)
1
st
Drill a 7/32''pilot hole
into each of the 4
center marks.
Drill a 7/32'' pilot hole
into each of the 4
center marks.
2
nd
Insert wall anchors
into pilot holes.
Insert wall anchors
into pilot holes.
4
8
I
Place a wall cup
over the center of
each circular
outline on the wall.
Mark drill holes
with a pencil
through the center
of each wall cup.

peel!
peel!
2
nd
3
rd
1
st
5
!
wall cup/top of stairs installation (continued)
press!
press!
press!
press!
6
9
x 4
G
x 4
F
Remove backing
from one side of each
adhesive mounting pad.
Align the wall cups so
the center hole is placed
directly over the wall
anchor. Stick the wall
cups to the wall.
Make sure all
wall cups are
facing up.
Attach one pad to the
back of each wall cup.
Remove backing.

x4
x 4
wall cup/top of stairs installation (continued)
7
8
10
D
Screw wall
cups into wall.
x 4
Repeat "installation"
steps on page 5.
The 4 tension bolts will
rest within each wall cup.