Summit Z Beam Shelving User manual

100–102KirkhamRdWest,Keysborough,3173VIC
Ph:1800352999W:www.summit.com.au



AssemblyInstructions
ZBeamShelving

PleasereadinstructionsCOMPLETELYpriortoassembly

Caution
Keepsmallchildrenclearduringassembly.
Handlecomponentswithcareduetosharpedges.

ToolsRequired
RubberMalletorHammer.

HelpfulHints
Useaclothorwoodenblocktoprotectthecomponentswhenhammering.
Hammergentlytoavoidcomponentdamage.
Driverivetstothebottomofthekeyholebystrikingthebeamnearthejoint.

Recommendations
Wearglovesduringassembly.
Twopersonsassembletheunit.
Assembletheunitonsolidlevelsurface.
Heaviestitemstobeloadedonlowershelves.
Loadstobeevenlydistributed.

PartsList




A–Uprights(8)B–LongBeam(10)C–ShortBeam(10)


D–ShelfDeck(5)E–PostCap(8)F–PostJoiner(4)


G–PostClips(2) 


100–102KirkhamRdWest,Keysborough,3173VIC
Ph:1800352999W:www.summit.com.au


AssemblyOption#1‐UprightShelvingUnit



Step1‐Unpacktheunit,confirmthatyouhaveallthepartslisted.

Step2‐Jointwouprightswithashortbeamtoformabottomendframeasperdiagram1.Drivetherivets
tothebottomofthekeyholebyhittingthebeamnearthejointwitharubbermallettolockthepieces
together.

NOTE:Itisimportantthatyouorientateallbeamssothattheflatpartoftheshelfledgeisfacingup.

Diagram1




100–102KirkhamRdWest,Keysborough,3173VIC
Ph:1800352999W:www.summit.com.au



Step3–Repeatstep2tocreateasecondbottomendframeandthenjointhetwobottomendframes
togetherwithlongbeamsasperdiagram2.

Diagram2



Step4–Createatopendframebyjoiningtwouprightswithashortbeamasperdiagram3.

Diagram3



Step5–RepeatStep4tocreateasecondtopendframe.


100–102KirkhamRdWest,Keysborough,3173VIC
Ph:1800352999W:www.summit.com.au


Step6–Jointhetopendframestothebottomendframesusingpostjoinersasperdiagram4.Asecond
persontoholdthetopendframessteadyatthispointisadvised.

Diagram4



Step7–Insertashortbeamtothemid‐sectionofthetopandbottomendframestocreateasecurejoin
asperdiagram5.Repeatfortheoppositesideandthenaddthelongbeams.

Diagram5




100–102KirkhamRdWest,Keysborough,3173VIC
Ph:1800352999W:www.summit.com.au


Step8–Addtwolongbeamstothetopoftheunitasperdiagram6.

Diagram6



Step9–Assembletheremaininglongandshortbeamstocreatetwoadditionalshelflevelsasperdiagram
7.Theseshelvescanbepositionasrequired.

Diagram7



100–102KirkhamRdWest,Keysborough,3173VIC
Ph:1800352999W:www.summit.com.au


Step10–Moveshelfunitintofinalpositionandthenlaytheshelfdecksontopofthebeamsasper
diagram8.Workfromthebottomup.Insertpostcapsonthetopandbottomoftheuprights.

Diagram8




Itisrecommendedthatyousecuretheuprightshelvingunittothewallwithfasteners(notsupplied).


AssemblyOption#2–Workbench








100–102KirkhamRdWest,Keysborough,3173VIC
Ph:1800352999W:www.summit.com.au


Step1.1–Createabottomassemblyaspersteps2and3.

Step1.2–Finishthemainworkbenchbayasperdiagram9.Middleshelflevelcanbesettodesiredheight.

Diagram9



Step1.3–Buildthesecondarybayendframeasperdiagram10.Pleasenotethatforstabilitythebottom
shelflevelneedstobeinthe7
th
and8
th
keyholeasillustrated.

Diagram10


Step1.4–Completethesecondarybaybyrepeatingstep1.3toformasecondendframeandthenjoining
togetherwithlongbeamsasperdiagram11

Diagram11



100–102KirkhamRdWest,Keysborough,3173VIC
Ph:1800352999W:www.summit.com.au



Step1.5–Positiontheworkbenchinfinallocationthenlayshelfdecksontopofthebeamsasperdiagram
12.

Diagram12



Step1.6–Securethetwobaysbyaligningthemiddleuprightsandfirmlyclampingtogetherwithapost
clipasperdiagram13.Dothisforfrontandback.Finishtheunitbyinsertingpostcapsonthetopofthe
uprights.

Diagram13

