Sun Glow SG Installation manual

1 of 7
02/05/2019
SG BI-DIRECTIONAL MOTOR
Programming Instructions
TECHNICAL SPECIFICATIONS
1. Ensure motor is protected. Any damages during transportation, storage, installation or misuse can cause the motor
to not work properly.
2. Charge the motor every 6 months to ensure optimal performance.
3. If the battery charge is at a lower level, the motor will beep 10 times to prompt that it needs to be charged.
4. Maximum running time of the motor is 6 minutes without limits. Motor will be asleep after six minutes has passed.
Motor will still be in wake up/programming mode once the motor has restarted.
MOTOR INFORMATION
Programming resides with the motor. Each motor can store up to
20 copied channels.
IF PURCHASING MORE THAN ONE CHARGER, PLEASE ENSURE THE OUTPUT
VOLTAGE ON THE CHARGER AND MOTOR MATCH.
To recharge the motor’s battery, connect the SG DC charger to the motor head charging jack and plug the charger into a
standard electrical outlet. When the battery is fully charged, the indication light on the charger will switch from red to green.
You can also use the SG Solar Panel to keep the battery constantly charged while exposed to su󰀩cient sunlight.
RECHARGING THE MOTOR
Charger Light
SIGNAL STRENGTH AND RANGE
MAY VARY DEPENDING ON THE
ACTUAL ENVIRONMENT.
CONTROL RANGE
L1 Open Area L2 With Obstructions Emission Frequency
200m 35m 433.92/868 MHz
55°C
-10°C
Working
Temperature
Obstructions
L2
L1
Roller Shade
Remote

Sun Glow Window Covering Products of Canada Ltd. www.mysunglow.com
2 of 7
TECHNICAL SPECIFICATIONS (CONTINUED)
BEFORE YOU BEGIN:
1. As a standard, motors are shipped in factory default mode without limits set.
2. Channel “0” cannot be programmed on a multi channel remote. It is intended to be a master
channel for all motors.
3. On a 15 channel remote, select the intended channel before activating wake-up mode, basic or
advanced program settings.
STEP 1: PREPARING FOR PROGRAMMING
REMOTE BUTTON LAYOUT
15 Channel
Remote
15 Channel Glass
Wall Switch
15 Channel
Wall Switch
Up Button
Stop Button
Down Button
Right/Left Buttons
(for switching
channels)
Remove Cover to
Expose Standard
Remote Back
P2 Setting Button
P2
MOTOR BUTTON LAYOUT Motor Setting
Button
Charging Jack
P2 Setting Button
P2
Up Button
Stop Button
Down Button
Right/Left Buttons
(for switching
channels)
P2 Setting Button
P2
(when held together)

Sun Glow Window Covering Products of Canada Ltd. www.mysunglow.com
3 of 7
STEP 1: PREPARING FOR PROGRAMMING
SWITCH DIRECTION
Setup is
complete
TEST SHADE
Move shade up and down to ensure that the direction
has been changed.
until motor jogs 1X
HOLD TOGETHER
Do not let the shade crash into the valance or unroll
from the tube.
Required to make the connection between the remote channel and the motor. During each of the following settings the
time between each operation must be shorter than 10 seconds, otherwise the program will be canceled, and the
motor will be back in default mode. Follow the steps below to wake-up the motor.
NO ASSIGNED LIMITS IN WAKE-UP MODE.
Motor beeps 3X
Setup is
complete
WAKE-UP MODE (Must Be Done Before Basic & Advanced Programming)
Motor
beeps
1X
HOLD
until motor jogs 2X
HOLD
until motor jogs 1X then RELEASE
to activate this motor
Allows you to set two positions: the upper and lower limits. This can be applied to each shade per channel.
During limit setting, the time between two operations must be shorter than 2 minutes, otherwise the program will be
cancelled, and the motor will be back in wake-up mode. Follow the steps below to set motor limits.
SETTING MOTOR LIMITS
TEST SHADE
Move shade up and down to test upper and lower limits.
Refer to "Adjusting Motor Limits" if limits require ne tuning.
GO TO DESIRED
UPPER LIMIT
GO TO DESIRED
LOWER LIMIT
Setup is
complete
Motor
beeps
3X
until motor jogs 2X
HOLD TOGETHER
Motor
beeps
3X
until motor jogs 2X
HOLD TOGETHER
STEP 2: BASIC PROGRAMMING
TEST SHADE
Move shade by holding the up or down button to ensure
that the motor works on the desired channel and moves in
the correct direction.
Do not let the shade crash into the
valance or unroll from the tube.
Holding up or down will move the
shade automatically

Sun Glow Window Covering Products of Canada Ltd. www.mysunglow.com
4 of 7
Allows you to set a third limit position for the shade per channel. Follow the steps below to set a preferred position.
STEP 3: ADVANCED PROGRAMMING
SETTING A PREFERRED POSITION
DELETING A PREFERRED POSITION
ADJUSTING MOTOR LIMITS
WHILE IN TILT FUNCTION SHADE WILL GO TO LOWER LIMIT FIRST AND THEN PROCEED TO THE
PREFERRED POSITION.
When setup is complete, hold the stop button to go to the preferred shade position. Follow the steps above to
program di󰀨erent preferred positions to separate channels on a 15 channel remote.
Setup is
complete
Setup is
complete
Motor
beeps
1X
Motor
beeps
1X
Motor
beeps
1X
Motor
beeps
1X
Motor
beeps
1X
Motor
beeps
1X
Motor
beeps
3X
GO TO
PREFERRED
POSITION
GO TO
PREFERRED
POSITION
PRESS
Motor jogs 1X
PRESS
Motor jogs 1X
PRESS
Motor jogs 2X
PRESS
Motor jogs 1X
PRESS
P2
Motor jogs
1X
PRESS
P2
Motor jogs
1X
GO TO UPPER OR LOWER LIMIT
OR
Setup is
complete
Motor
beeps
3X
PRESS
OR
ADJUST LIMIT
until motor jogs 1X
HOLD TOGETHER
upper limit lower limit
OR
until motor jogs 1X
HOLD TOGETHER
upper limit lower limit
OR

Sun Glow Window Covering Products of Canada Ltd. www.mysunglow.com
5 of 7
Each motor has three speeds. To move between the di󰀨erent speeds, follow the diagram below.
SPEED ADJUSTMENT
TILT MODE INCREMENTAL MOVEMENT
SETTING TILT MODE
DELETING TILT MODE
Tilt mode is used to move the shade in small increments for ne adjustment. It is most
e󰀨ective when programmed with a standard remote (button remote). Follow the steps
below to set the shade in tilt mode or remove shade from tilt mode.
TILT MODE WILL REMAIN ACTIVE IN ALL MODES (EXCEPT STEP 2: BASIC PROGRAMMING) UNLESS
REMOVED
Recommended with Interlude or
Illusions shades.
Interlude Illusions
TEST SHADE
press the up or down buttons repeatedly for ne adjustment. To move shade automatically, hold the up or down
buttons and release once the shade begins to move.
Motor
beeps
1X
PRESS
P2
Motor jogs
1X
Gear Down
Gear Up
Motor jogs 1X
Motor jogs 1X
Motor jogs 1X
Motor jogs 1X
PRESS
PRESS
PRESS
PRESS
Motor
beeps
1X
Motor
beeps
1X
Motor
beeps
2X
Motor
beeps
2X
STEP 3: ADVANCED PROGRAMMING (CONTINUED)
Motor
beeps
1X
PRESS
Motor jogs 1X
Setup is
complete
until motor jogs 1X
HOLD TOGETHER
Motor
beeps
3X
PRESS
Motor jogs 2X
Setup is
complete
until motor jogs 1X
HOLD TOGETHER

Sun Glow Window Covering Products of Canada Ltd. www.mysunglow.com
6 of 7
STEP 3: ADVANCED PROGRAMMING (CONTINUED)
COPY OR DELETING FROM A PREVIOUSLY PROGRAMMED MOTOR
DELETING OR TRANSFERRING GROUPS OF MOTORS ARE RECOMMENDED TO BE DONE USING
THE ORIGINAL REMOTE THAT WAS SET UP.
COPYING, DELETING OR GROUPING WITH A REMOTE
The remote scenario chart below outlines di󰀨erent ways to copy, delete or group channels using separate remotes.
1
Channel
1
Channel
1-15
Grouped
Channels
or
1,2,3...15
Separate
1-15
Grouped
Channels
or
1,2,3...15
Separate
DELETING CHANNELS
Note: this only works on previously copied/grouped channels.
COPYING/GROUPING CHANNELS
Setup is
complete
Using
original
remote
or
channel
Motor
beeps
1X
Motor jogs 1X
PRESS
P2
Using
original
remote
or
channel
Motor
beeps
1X
Motor jogs 1X
PRESS
P2
Using new
remote or
channel
(to be copied
or grouped) Motor jogs 2X
PRESS
P2 Motor
beeps
3X
Setup is
complete
Using
original
remote
or
channel
Motor
beeps
1X
Motor jogs 1X
PRESS
P2
Using
original
remote
or
channel
Motor
beeps
1X
Motor jogs 1X
PRESS
P2
Using new
remote or
channel
(to be deleted)
Motor jogs 1X
PRESS
P2 Motor
beeps
3X
Motor
beeps
1X
Setup is
complete
Motor
beeps
3X
HOLD
until motor jogs 1X then
RELEASE to activate this motor
HOLD
until motor jogs 2X
The motor factory reset mode will wipe all transmitters/remotes.
MOTOR RESET
Setup is
complete
Motor
beeps
4X
HOLD
until motor jogs 4X
then RELEASE
Only perform a motor reset if necessary.
Separate channels can also be programmed this way within one 15 channel remote. Follow the steps below to copy,
delete or group channels.

Sun Glow Window Covering Products of Canada Ltd.
Manufacturer & Wholesale Distributor
Telephone: [phone] Toll Free: 800.668.1728
Fax: [phone] Toll Free: 877.245.9943
50 Hollinger Road, Toronto, Ontario M4B 3G5 www.mysunglow.com
7 of 7
This mode allows you to operate the shade in the event that the remote goes missing or is lost.
The change of direction can be done after limits have been set.
OPERATING SHADE AT MOTOR HEAD
SWITCHING DIRECTION AT MOTOR HEAD
MOTOR SHIELDING
STEP 3: ADVANCED PROGRAMMING (CONTINUED)
The mode allows a motor’s wireless radio signal to become temporarily disabled to save the battery life.
If no limits are set, the motor will not move when enabled.
DISABLE SIGNAL: Setup is
complete
Motor
beeps
2X
HOLD
until motor jogs 2X
then RELEASE
ENABLE SIGNAL: Setup is
complete
Motor will
automatically
move to previously
assigned limit
HOLD
until motor jogs 2X
then RELEASE
Note: pressing the motor setting button
while the shade is moving can also stop
the motor.
HOLD
until motor jogs 2X
then RELEASE
Setup is
complete
Motor
beeps
3X
HOLD
until motor jogs 3X
then RELEASE
TEST SHADE
Move shade up and down to ensure that the
direction has been changed.