Sune Technology Q-ROI Golf User manual

Your best partner for better driving
SUNE TECHNOLOGY CO.,LTD
No.9,Lane 606,Anping Rd,Tainan City 70849,TAIWAN
TEL:[phone] FAX:[phone]
Http://www.sune-tech.com
Shop http://www.carnavi-tech.com
SKYPE:sune_tech or hsin_han99
CarNavi-Tech

Index
1. General spec
2. System Diagram
3. Components
4. Original button use
5. Setting up Dip S/W
6. Setting up FACTORY MENU
7. Cautions before Installation
8. Installation Diagram
9. Installation
10.Quality Warranty
CarNavi-Tech

Do not modify, dismantle or unintended
operation this system outside Q-roi After Sales.
Damage occurred by unintended operation
may cause Q-roi After Sales service void.
Warning
Always wear seatbelt. When the vehicle is
suddenly stop can cause injury.
Remove dust, oil, and waste on the display.
Incidental damages (including, without
limitation, consequential damages due to the
use of this unit and the dead loss of business
profit, changes, loss of memory contents, etc)
will not be taken responsibility.
•Any function that requires your prolonged
attention should only be performed after
coming to a complete stop. Always
stop the vehicle in a safe location before
performing these functions. Failure to do so
may result in an accident.
The engine is off while the system operates for
long time, battery may be discharged.
This product is not a substitute for your
personal judgment. Any route suggested by
this navigation system may never supersede
any local traffic regulation. Do not follow route
suggestions if the navigation system instructs
you to perform an unsafe or illegal maneuver.
Warning
Warning / Precautions!
CarNavi-Tech

1. General Spec
OS
Android 4.2.2 (Jelly Bean)
CPU
Telechips TCC8930 (1GHz Cortex A9 DualCore)
Display
OEM LCD
Internal Memory
DDR3 1GB RAM + 8GB eMMC
External Memory
SDHC Slot Support (up to 64GB)
Function
A/V Input x 3,
Rear Cam Input x 1,
CAN(Controller Area Network) x 2,
Mic x 1,
External Speaker x 1 (mono),
External Audio Out x 1(Car Aux),
Output
LVDS ( thru Video Interface),
RGB (thru Sub-Board)
Touch Type
Resistive Touch
GPS
SiRF
Resolution
800*480 or 1024*480
USB
USB 2.0 x 5 (USB x 4, OTG USB x 1)
Input Voltage
12V
Temperature
operating 0 C to 60 C
Storage -20 C to 60 C
Languages
multi-languages
CarNavi-Tech

2. System Diagram
Application
Processor
DDR3
1GB
eMMC
Flash
Memory
8GB
Video
Decoder
Audio
Decoder
/Encoder
Image
Scaler
LVDS
Transmitter
Microprocess
or
With
2 CAN ports
CAN
Transceivr
CAN
Transceiv
e
USB HUB
Audio Amp.
Touch
Screen
Controller
LCD Display
Rear Camera
DVD Player
Other Composite
Video Signal
Speakers
Touch
Screen
Button CAN
data
Steering wheel
CAN data
USB Devices
- USB memory
- Hard Disc
- Wifi dongle
- BlueTooth dongle
- 3G / LTE dongle
- Other USB
Accessories
Microphone
CarNavi-Tech

3. Components
MODE switch cable* 1ea
(HARETC0001)
USB cable * 2ea
(HARETC0078)
REAR CAMERA cable * 1ea
(HARETC0002)
Speaker * 1ea
(SPEAKE0001)
AV/BT Cable * 1ea
(HAVCAB0020)
GPS Antenna * 1ea
(GPSANT0006)
Multi cable * 1ea
(HARETC0068)
Power cable 16P * 1ea
(HPOWER0041)
Microphone cable * 1ea
(MICPHO0001)
3G dongle * 1ea(Option)
(ETCETC0116)
WIFI dongle * 1ea(Option)
(ETCETC0110) Sub-Board * 1ea
LCD cable * 1ea
(HLCDCA0007)
CAN IN/OUT cable * 1ea
(HARETC0076)
LVDS cable* 1ea
(HALVDSC0024)
SD 연장 케이블 * 1ea
(HARETC0080)
CarNavi-Tech

4. Original button use
※ GOLF
※SKODA OCTAVIA
Press and hold :
Mode change
(Q-ROI↔Original
screen)
Press and hold
: Q-ROI Reset
Use ‘Mute’ button
to reset in case no
such button
<Left side buttons of steering wheel>
<Left side buttons
Of steering wheel>
Press and hold :
Q-ROI Reset
Press and hold :
Mode change
(Q-ROI↔Original screen)
※New VW car
Press and hold :
Mode change
(Q-ROI↔Original
screen)
<Right side buttons
Of steering wheel>
CarNavi-Tech

5. Setting up Dip Switch
※Dip Switch Setting (Main board)
※Dip Switch Setting (I/F)
: Old GOLF, SKODA OCTAVIA
: New SKODA OCTAVIA
: New VW GOLF, PASSAT
1
Setup Car
OFF : Old SKODA, GOLF
ON : New SKODA, GOLF,
PASSAT
2
Setup
Touch
OFF : Old car
ON : New car
3
Setup Model
OFF : QNAVI(Win CE)
ON : Q-ROI(Android)
4
Setup
resolution
OFF : Low resolution
ON : High resolution
※MAIN BOARD : Steering wheel button, I/F : Monitor setting up
※Please make sure to disconnect the power cable of the interface and reconnect
the power cable again to apply the dip switch setting whenever changing DIP switch.
Otherwise, DIP switch setting will not be applied.
CarNavi-Tech

6. Setting up Factory Menu
※APPS→FACTORY SETTING
①Put Password and change program upgrade and set-up of
external device. (Only Installers are authorized)
※Please contact the manufacturer to get Password.
CarNavi-Tech

6. Setting up Factory Menu
①
③
②
④
⑤
①CAR MODEL : No use
②DVD TYPE : Only for DVD connected to A/V
(Connect IR-AV1 to DVD to use DVD as touch Screen)
③CMMB SELECT : Select DTV model ( Only Chinese)
④SETTING
- GEAR CHECK TYPE : Detecting rear camera via either CAN or Rear Lamp.
- REAR CAM : Put “On” – External rear camera
Put “Off “ – OEM Camera
- SAFE MODE : Either Enable or Unable to watch Video while driving
- MODE SWITCH : NO use
⑤SAVE & EXIT : Save and Reboot
CarNavi-Tech

7. Cautions before Installation
Ignition key should be taken off before starting installation, interface
power connection must be the last step in installation.
Power cable should be separated when connecting interface.
Should be no any electronic devices or magnetic pole around
installation place.
All steps of installation should be done by well-trained specialist.
Dismantling without manufacturer’s permission can not be
guaranteed, (No permission to break attached label on the board.)
Kindly check all parts are in the box, when receiving the product, if
anything missing, inform to the supplier or manufacturer.
Install GPS away from electromagnetic devices such as black boxes,
Hi-Pass and etc.
Advisable to Install GPS at the edge of dash board or a front window
or a rear window.
Install GPS antenna mounted on window or roof facing to Sky .
According to our sales policy, any problems caused by user’s
mistake, careless can not be guaranteed.
CarNavi-Tech

8. Installation Diagram
REAR CAM
POWER
cable
GPS
SPK
Speaker
REAR (12V OUT)
GND
TOGGLE
MIC
POWER cable
ACC
CAN1-
H
AUX-GND
A OUT(R)
CAN2-
H
GND
N.C
A OUT(L)
CAN1-L
CAN2-L
FRONT
SAFE
REAR
MMI
AUX-ON
오리지널
모니터
Provided LCD Cable
Origianl LCD Cable
SD Card
※1. Remove Original LCD cable from Monitor and
Connect OEM LCD cable to Sub-Board“LCD-OUT".
2. Connect Provided LCD cable to Behind of monitor.
Head unit
<Inside of Glove box>
<Behind of monitor>
CarNavi-Tech

9. Installation
8.1 Connection between a monitor and an interface
※1. Remove Original LCD cable from Monitor and
Connect OEM LCD cable to Sub-Board“LCD-OUT".
2. Connect Provided LCD cable to Behind of monitor.
Head unit
Original LCD Cable
provided LVDS Cable
Provided LCD Cable
<Behind of monitor>
<Inside of Glove box>
CarNavi-Tech

9. Installation
8.2 Connection of CAN Wire -1
You should be able to find CAN wire behind the air-conditioner.
Connect CAN1-H(Orange + Green) to CAN-H(Yellow + White) of Car.
Connect CAN1-L(Orange + Brown) to Original CAN-L(Yellow ) of Car.
Connect to CAN1-H of Power cable
Connect to CAN1-L of Power cable
CarNavi-Tech

9. Installation
8.3 Connection of CAN Wire-2
①Pull away the black
connect from a monitor
②Put away the black cap.
③Connect the black connector
covered in silver cap to the
provided CAN IN/OUT cable
covered in white cap .
④Connect the other side of the
provided CAN IN/OUT cable to the
port where OEM connector was
removed.
CarNavi-Tech

This product has been tested and have passed under our strict
quality control. If the failure occurred due to the carelessness of
workmanship within one year after the purchase, we are
responsible to repair free of charge.
Please bring this warranty to dealer whom you purchased this
product from at the repair time. Should this warranty not
presented, repair charged will be on customer. Please keep this
warranty card.
Warranty
Product
name
Warranty
period
1 year
Purchase
date
(yy/mm/dd)
Customer
Address
TEL
Name
Dealer
Address
Name
10. Quality Warranty
CarNavi-Tech