Sunfull 1002-LITE User manual

Installation instructions
Suitable gateway type（1 network port 4 serial port ：4 RS485, 1 RS232）
Basic version: W7-1041
Gateway version: W7-1041-GW
1.0 Before use the software configuration step (refer to the relevant configuration
software operation manual), please confirm the following:
- the configuration project is correct;(please refer to the X2View configuration software
operation instructions for details)
- upload engineering files to the touch panel;
- simulation test to collect data;
2.0 Touch panel size
7 inch touch panel Hole size: 210.5mm x 146.5mm (L * W) weight: 550g
Installation method: (Card buckle installation)
3.0 wiring instructions
Power supply: AC/DC 9~24V (rated power 5W);
Network port: default IP address 192.168.1.88;
Full isolation RS485 interface: (COM1, COM2, COM3, COM4)
A positive (+) B negative (-) GND (ground)
Full isolation RS232 interface: Rx (2) TX (3) GND (5)
DB9-M: Gateway RX (2) ~~ device TX (3)
Gateway TX (3) ~~ device RX (2)
Gateway GND (5) ~~ equipment GND (5)
DB9-F: Gateway RX (2) ~~ device RX (2)
Gateway TX (3) ~~ device TX (3)
Gateway GND (5) ~~ equipment GND (5)
4.0 Login touch panel Web server
Under the network cable to the Ethernet port, enter the URL on the browser:
http://192.168.1.88/login.html Login Username: admin Password: admin123456
Note: download gateway configuration software after entering the web server, please
refer to the PDF document under the Help folder for specific operation.
5.0 common problems
Q1: how to modify the IP address of the gateway/touch panel?
A1: The gateway factory default IP address 192.168.1.88, subnet mask 255.255.255.0, default
gateway 192.168.1.1.

For the first time using, user need a cable directly connect computer and gateway/touch
panel, and then change the IP address to the computer and gateway/touch panel within the
same network segment (e.g., computer IP to 192.168.1.55), after confirmation to ping, open
the browser, enter the URL: http://192.168.1.88/ login. HTML, log on to the Web server, as
shown above in the " network" column set IP address.
Q2: What if the project files are not found in the computer?
A2: The project files can be downloaded in the configuration software; or login the
gateway/touch panel to the WEB page "download " and click "project file" to download.
Q3: what is the difference between different models of the gateway hardware?
A3:The main models are as follows:
Model
Hardware
Parameter
Interfaces
Supported
Points
Supported Ports
1002-LITE
CPU：240MHz
Memory：32M
1 ethernet
2 serial ports
256
2 RS485 &
2 RS232
1002-ARM
CPU：240MHz
Memory：32M
1 ethernet
2 serial ports
256
2 RS485 &
2 RS232
2004-LITE
CPU：400MHz
Memory：64M
2 ethernets
4 serial ports
1024
4 RS485
2004-ARM
CPU：400MHz
Memory：64M
2 ethernets
4 serial ports
1024
4 RS485
2004-A9
CPU：1.4GMHz
Memory：512M
2 ethernets
4 serial ports
2048
4 RS485
1022-1U
CPU：400MHz
Memory：DDR2
1 ethernets
4 serial ports
1024
4 RS485
Sunfull Gateway model
BACnet Gateway: BAC1002-LITE(economical),BAC1002-ARM,BAC2004-LITE(economical),
BAC2004-ARM, BAC2004-A9
Modbus Gateway: MOD1002-LITE (economical), MOD1002-ARM, MOD2004-LITE (economical),
MOD2004- ARM, MOD2004-A9
Modbus Hub Gateway: HUB1002- ARM, HUB2004-ARM
SMS Alarm Gateway: HMI2004-A9-GPRS
SNMP Gateway: SNMP1002- ARM, SNMP2004-ARM
IEC104 Gateway: IEC 2004-ARM
WEB Configuration Gateway: HMI2004-A9-GW
Sunfull WEB Touch Panel series
Basic version: W7-1041
Gateway version: W7-1041-GW, W10-1041-GW, W15-1041-GW
Sunfull Software Gateway
OPC transfer BACnet: O2B- Softkey, O2B-USBkey
OPC transfer Modbus: O2M- Softkey, O2M-USBkey
OPC transfer Modbus- cloud: O2M-WEB- Softkey, O2M-WEB-USBkey
OPC transfer IEC104: O2I-Softkey、O2I-USBkey
OPC transfer SMS: O2S-Softkey、O2S-USBkey
OPC transfer Web: O2W-Softkey、O2W-USBkey
OPC transfer SNMP: OtS-Softkey、OtS-USBkey
Sunfull OPC server
OPC server: X2O- Softkey, X2O-USBkey
OPC server: OPCHub
Sunfull Free Software
BACnetScan scanning tool, MBUS scanning tool, Niagara interface, and WEBS interface
Welcome to follow Shanghai Sunfull’s wechat public number : BACnet
to know more new products and solutions.
Shanghai Sunfull Automation Co., LTD. TEL: [phone]
Address: A466,building1, NO.2588,JinhaiRoad,Pudong,Shanghai,China
Technical support E-mail: [email protected]
Technical support Tel: [phone] Website 1: www.bacnetchina.com
SalesTel: 13564889340 Contacts: Linda Chen Website 2: www.opcmaster.com