sunjoe 24V-AJV-CT User manual

A Division of Snow Joe®, LLC Model 24V-AJV-CT Form No. SJ-24V-AJV-CT-880E-M
R
OPERATOR’S MANUAL
© 2020 by Snow Joe®, LLC
All rights reserved. Original instructions. SAVE THESE INSTRUCTIONS
1
CORDLESS INFLATOR+DEFLATOR –
TOOL ONLY
24-VOLT MAX*| INFLATION ADAPTERS
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Always follow these safety guidelines. Failure to do so may
result in serious bodily injury or death.
General Power Tool Safety
Warnings
m WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in serious injury or death.
mWARNING! This indicates a hazardous situation, which,
if not followed, could result in serious injury or death.
mCAUTION! This indicates a hazardous situation, which,
if not followed, could result in minor or moderate injury.
Work Area Safety
1. Keep work area clean and well-lit – Cluttered, dark
areas invite accidents.
2. Keep children, bystanders, and pets away –
All spectators, including pets, should be kept a safe
distance away from the work area.
3. Operatecordlesshighvolumeinatorinanopenarea
at least 18 in. (45.7 cm) away from any wall or object
thatcouldrestricttheowairtoventilationopenings.
Electrical Safety
1. To reduce the risk of electrical shock, do not put
inatorinwaterorotherliquid.Do not place or store
appliance where it can fall or be pulled into a tub or sink.
2. Rechargeonlywiththechargerspeciedbythe
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used with
another battery pack.
Personal Safety
1. Stay alert – Watch what you are doing. Use common
sense. Do not operate the cordless high volume inator
when you are tired, or under the inuence of alcohol or
drugs.
2. Dress properly – Do not wear loose clothing or jewelry.
They can get caught in moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
3. Avoid unintentional starting – Do not carry the cordless
high volume inator with your nger on the trigger.
4. Do not overreach – Keep proper footing and balance
at all times. Proper footing and balance enable better
control of the cordless high volume inator in unexpected
situations.
5. Usesafetyequipment–Always wear eye protection.
Dusk mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
6. Eyeprotectionisrequiredtoguardagainstying
fasteners and debris which could cause severe eye
injury.
7. Do no wear loose clothing or jewelry – Contain long
hair. Loose clothes, jewelry, or long hair can be drawn into
air vents.
8. Do not use on a ladder or unstable support – Stable
footing on a solid surface enables better control of the
cordless high volume inator in unexpected situations.
9. Do not force the tool – It will perform better with less
likelihood of personal or mechanical injury if it is used at
the rate for which it was designed.
10. Release all pressures within the system slowly.
Dust and debris may be harmful.
11.Donotusecordlesshighvolumeinatorifswitchdoes
notturnitonoro.The cordless high volume inator
that cannot be controlled with the switch is dangerous
and must be repaired.
12. Disconnect battery pack from the cordless high
volumeinatorbeforemakinganyadjustments,
changing accessories, or storing the cordless high
volumeinator. Such preventive safety measures reduce
the risk of starting the cordless high volume inator
accidentally.
13.Storeidlecordlesshighvolumeinatoroutofreach
of children or other untrained persons. Cordless high
volume inators are dangerous in the hands of untrained
users.

2
14. When battery pack is not in use, keep it away from metal
objects like: paper clips, coins, keys, nails, screws,
or other small metal objects that can make a connection
from one terminal to another. Shorting the battery
terminals together may cause sparks, burns, or a re.
15. Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
aectthecordlesshighvolumeinator'soperation.
Ifdamaged,havethecordlesshighvolumeinator
serviced before using. Many accidents are caused by
poorly maintained tools.
16. Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one cordless high volume inator may create a
risk of injury when used on another cordless high volume
inator.
17.Keepthecordlesshighvolumeinatoranditshandle
dry, clean and free from oil and grease. Always use a
clean cloth when cleaning. Never use brake uid, gasoline,
petroleum-based products, or any strong solvents to
clean your cordless high volume inator. Following this
rule will reduce the risk of loss of control and deterioration
of the enclosure plastic.
18.Neverpointanycordlesshighvolumeinatortoward
yourself or others.
19. Do not exceed the pressure rating of any component
in the system.
SpecicSafetyWarnings
for Cordless High volume
inator
1. Knowyourcordlesshighvolumeinator–Know how
to start and stop the tool. Be thoroughly familiar with
the controls.
2. Risk of bursting – Do not preset cordless high volume
inator to result in output pressure greater than marked
maximum pressure of item to be inated. Do not use at
pressure greater than 0.65 PSI.
3. To reduce the risk of electric shock, do not expose to rain.
Store indoors.
4. Inspect yearly for cracks, pin holes, or other
imperfections that could cause cordless high volume
inatortobecomeunsafe.Never cut or drill holes in the
high volume inator.
5. Use the right appliance – Do not use the cordless high
volume inator for any applications other than those for
which it was intended.
6.
Check for damaged parts – Before further use of the
cordless high volume inator or air tool, all guards and
parts should be carefully checked to determine that it will
operate properly and perform its intended function. Check
for alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other condition
that may aect its operation. A guard or other part that is
damaged should be properly repaired or replaced. Contact
the Snow Joe
®
+ Sun Joe
®
customer service center at
1-866-SNOWJOE (1-866-766-9563) fo
r assistance.
7. Remove the battery – Remove the battery from the
cordless high volume inator when it is not in use, before
servicing it, when changing accessories, and when
performing any other maintenance task.
8. Protect your lungs – Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the risk
of serious personal injury.
9. Do not use cordless high volume inator as a breathing
device.
10. Never direct a jet of compressed air toward people or
animals. Take care not to blow dust and dirt towards
yourself or others. Following this rule will reduce the risk
of serious injury.
11. Do not use this cordless high volume inator to spray
chemicals. Your lungs can be damaged by inhaling
toxic fumes.
12. Always be aware that misuse and improper handling of
this cordless high volume inator can cause injury to
yourself and others.
13. Do not continue to use a cordless high volume inator that
leaks air or does not functions properly.
14. Always follow all safety rules recommended by the
manufacturer of your cordless high volume inator,
in addition to all safety rules for the cordless air inator.
Following this rule will reduce the risk of serious personal
injury.
15. Do not crush, drop or damage battery pack. Do not use a
battery pack or charger that has been dropped or received
a sharp blow. A damaged battery is subject to explosion.
Properly dispose of a dropped or damaged battery
immediately.
16. Do not charge battery tool in a damp or wet location.
Following this rule will reduce the risk of electric shock.
17. Inspect tool cords periodically and, if damages, have
repaired at your nearest authorized service center.
Constantly stay aware of cord location. Following this rule
will reduce the risk of electric shock or re.
mWARNING! Do not use this cordless high volume
inator without reading this instruction manual. For indoor use
only.
Battery & Charger
Safety Instructions
NOTE: This unit is the tool only. The battery and the charger
are not included. They must be purchased separately.
Model 24V-AJV-CT is compatible with the iON+ 24V System
batteries and chargers. See page 13 for more information.
We pay a great deal of attention to the design of every battery
pack to ensure that we supply you with batteries that are safe,
durable and have a high energy density. The battery cells have
a wide range of safety devices. Each individual cell is initially
formatted and its electrical characteristic curves are recorded.
This data is then used exclusively to be able to assemble the
best possible battery packs.

3
Despite all the safety precautions, caution must always be
exercised when handling batteries. The following points must
be obeyed at all times to ensure safe use. Safe use can only
be guaranteed if undamaged cells are used. Incorrect handling
of the battery pack can cause cell damage.
IMPORTANT! Analyses conrm that incorrect use and poor
care of high-performance batteries are the main factors
responsible for personal and/or product damage.
mWARNING! Use only approved replacement batteries;
other batteries may damage the power tool and cause it to
malfunction, which can lead to serious personal injury.
mWARNING! Do not use a battery pack or appliance that
is damaged or modied. Damaged or modied batteries may
exhibit unpredictable behavior resulting in re, explosion or
risk of injury.
Do not modify or attempt to repair the appliance or the battery
pack except as indicated in the instructions for use and care.
Have your battery pack serviced by a qualied repair person
using only identical replacement parts. This will ensure that the
safety of the battery pack is maintained.
mCAUTION! To reduce the risk of injury, charge the
iON+ 24V lithium-ion battery pack only in its designated
iON+ 24V lithium-ion charger. Other types of chargers present
risk of re, personal injury and damage. Do not wire a battery
pack to a power supply plug or car cigarette lighter. Such
misuse will permanently disable or damage the battery pack.
• Avoid dangerous environments – Do not charge the
battery pack in rain, snow or in damp or wet locations.
Do not use the battery pack or charger in the presence of
explosive atmospheres (gaseous fumes, dust or ammable
materials) because sparks may be generated when inserting
or removing the battery pack, which could lead to a re.
• Charge in a well-ventilated area – Do not block the
charger vents. Keep them clear to allow for proper
ventilation. Do not allow smoking or open ames near a
charging battery pack. Vented gases may explode.
NOTE: The safe temperature range for the battery is
41°F – 105ºF (5°C – 40.5°C). Do not charge the battery
outside in freezing weather; charge it at room temperature.
• Maintain charger cord – When unplugging the charger,
pull the plug, not the cord, from the receptacle to reduce
the risk of damage to the electrical plug and cord. Never
carry the charger by its cord or yank it by the cord to
disconnect it from the receptacle. Keep the cord away
from heat, oil and sharp edges. Make sure the cord will not
be stepped on, tripped over or subjected to damage or
stress when the charger is in use. Do not use the charger
with a damaged cord or plug. Replace a damaged charger
immediately.
• Do not use an extension cord unless it is absolutely
necessary – Using the wrong, damaged or improperly
wired extension cord poses a risk of re and electric shock.
If an extension cord must be used, plug the charger into a
properly wired 16 gauge or larger extension cord with the
female plug matching the male plug on the charger. Make
sure that the extension cord is in good electrical condition.
• Check the rated input for the charger before using – The
charger must be plugged into an appropriate receptacle.
• Use only recommended attachments – Use of an
attachment not recommended or sold by the battery
charger or battery pack manufacturer may result in risk
of re, electric shock or personal injury.
• Unplug charger when not in use – Make sure to remove
battery packs from unplugged chargers.
mWARNING! To reduce the risk of electric shock,
always unplug the charger before performing any cleaning or
maintenance. Do not allow water to ow into the charger.
Use a Ground Fault Circuit Interrupter (GFCI) to reduce
shock hazards.
• Do not burn or incinerate battery packs – Battery packs
may explode, causing personal injury or damage. Toxic
fumes and materials are created when battery packs are
burned.
• Do not crush, drop or damage battery packs – Do not
use the battery pack or charger if they have sustained a
sharp blow, been dropped, run over or have been damaged
in any way (i.e. pierced with a nail, hit with a hammer,
stepped on, etc.).
• Do not disassemble – Incorrect reassembly may pose
a serious risk of electric shock, re or exposure to toxic
battery chemicals. If the battery or charger are damaged,
contact an authorized Snow Joe®+ Sun Joe®dealer or
call the Snow Joe®+ Sun Joe®customer service center at
1-866-SNOWJOE (1-866-766-9563) for assistance.
• Battery chemicals cause serious burns – Never let a
damaged battery pack contact the skin, eyes or mouth. If a
damaged battery pack leaks battery chemicals, use rubber
or neoprene gloves to safely dispose of it. If skin is exposed
to battery uids, wash the aected area with soap and
water and rinse with vinegar. If eyes are exposed to battery
chemicals, immediately ush with water for
20 minutes and seek medical attention. Remove and
dispose of contaminated clothing.
• Do not short circuit – When battery pack is not in use,
keep it away from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal objects,
that can make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a re.
• Store your battery pack and charger in a cool,
dry place – Do not store the battery pack or charger where
temperatures may exceed 105ºF (40.5ºC), such as in
direct sunlight or inside a vehicle or metal building
during the summer.

4
Information about the battery
1. The battery pack is only partially charged. The battery
pack has to be charged completely before you use the
tool for the rst time.
2. For optimum battery performance, avoid low discharge
cycles by charging the battery pack frequently.
3. Store the battery pack in a cool place, ideally at 59°F
(15°C) and charged to at least 40%.
4. Lithium-ion batteries are subject to a natural aging
process. The battery pack must be replaced at the latest
when its capacity falls to just 80% of its capacity when
new. Weakened cells in an aged battery pack are no
longer capable of meeting the high power requirements
needed for the proper operation of your cordless high
volume inator, and therefore pose a safety risk.
5. Do not throw battery packs into an open re as this poses
a risk of explosion.
6. Do not ignite the battery pack or expose it to re.
7. Do not exhaustively discharge batteries. Exhaustive
discharge will damage the battery cells. The most
common cause of exhaustive discharge is lengthy storage
or non-use of partially discharged batteries. Stop working
as soon as the performance of the battery falls noticeably
or the electronic protection system triggers. Place the
battery pack in storage only after it has been fully charged.
8. Protect batteries and the tool from overloads. Overloads
will quickly result in overheating and cell damage inside
the battery housing even if this overheating is not
apparent externally.
9. Avoid damage and shocks. Immediately replace batteries
that have been dropped from a height of more than
3 feet (1 meter) or those that have been exposed to violent
shocks, even if the housing of the battery pack appears to
be undamaged. The battery cells inside the battery may
have suered serious damage. In such instances,
please read the waste disposal information for proper
battery disposal.
10. If the battery pack suers overloading and overheating,
the integrated protective cuto will switch o the
equipment for safety reasons.
IMPORTANT! Do not press the ON/OFF switch any more
if the protective cut-o has been activated. This may
damage the battery pack.
11. Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of re when used with
another battery pack.
12. Use appliances only with specically designated battery
packs. Use of any other battery packs may create a risk of
injury and re.
13. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally occurs,
ush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.
14. Do not use a battery pack or appliance that is damaged
or modied. Damaged or modied batteries may exhibit
unpredictable behavior resulting in re, explosion or risk
of injury.
15. Do not expose a battery pack or appliance to re or
excessive temperature. Exposure to re or temperature
above 266ºF (130°C) may cause explosion.
16. Follow all charging instructions and do not charge the
battery pack or appliance outside of the temperature
range specied in the instructions. Charging improperly
or at temperatures outside of the specied range may
damage the battery and increase the risk of re.
Information about the charger and the
charging process
1. Please check the data marked on the rating plate of the
battery charger. Be sure to connect the battery charger
to a power supply with the voltage marked on the rating
plate. Never connect it to a dierent mains voltage.
2. Protect the battery charger and its cord from damage.
Keep the charger and its cord away from heat, oil and
sharp edges. Have damaged cords repaired without delay
by a qualied technician at an authorized Snow Joe®+
Sun Joe®dealer or call the Snow Joe®+ Sun Joe®
customer service center at 1-866-SNOWJOE
(1-866-766-9563).
3. Electrical plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
grounded appliances. Unmodied plugs and matching
outlets will reduce the risk of electric shock.
4. Keep the battery charger, battery pack(s) and the cordless
tool out of the reach of children.
5. Do not use the supplied battery charger to charge other
cordless tools.
6. During periods of heavy use, the battery pack will become
warm. Allow the battery pack to cool to room temperature
before inserting it into the charger to recharge.
7. Do not overcharge batteries. Do not exceed the maximum
charging times. These charging times only apply to
discharged batteries. Frequent insertion of a charged or
partially charged battery pack will result in overcharging
and cell damage. Do not leave batteries in the charger for
days on end.
8. Never use or charge batteries if you suspect that it has
been more than 12 months since the last time they were
charged. There is a high probability that the battery pack
has already suered dangerous damage (exhaustive
discharge).
9. Charging batteries at a temperature below 41°F (5°C) will
cause chemical damage to the cells and may cause a re.
10. Do not use batteries that have been exposed to heat
during the charging process, as the battery cells may have
suered dangerous damage.
11. Do not use batteries that have suered curvature or
deformation during the charging process or those that
exhibit other atypical symptoms (gassing, hissing,
cracking, etc.).

5
12. Never fully discharge the battery pack (maximum
recommended depth of discharge is 80%). A complete
discharge of the battery pack will lead to premature aging
of the battery cells.
Protectionfromenvironmentalinuences
1. Wear suitable work clothes. Wear safety goggles.
2. Protect your cordless tool and the battery charger from
moisture and rain. Moisture and rain can cause dangerous
cell damage.
3. Do not use the cordless tool or the battery charger near
vapors and ammable liquids.
4. Use the battery charger and cordless tools only in dry
conditions and at an ambient temperature of 41ºF – 105°F
(5°C – 40.5°C).
5. Do not keep the battery charger in places where the
temperature is liable to reach over 105°F (40.5°C). In
particular, do not leave the battery charger in a car that is
parked in the sunshine.
6. Protect batteries from overheating. Overloads,
overcharging and exposure to direct sunlight will result
in overheating and cell damage. Never charge or work
with batteries that have been overheated – replace them
immediately, if possible.
7. Store the charger and your cordless tool only in dry
locations with an ambient temperature of 41ºF – 105°F
(5°C – 40.5°C). Store your lithium-ion battery pack in a
cool, dry place at a temperature of 77°F (25°C). Protect
the battery pack, charger and cordless tool from humidity
and direct sunlight. Only place fully charged batteries in
storage (charged to at least 40%).
8. Prevent the lithium-ion battery pack from freezing.
Battery packs that were stored below 32°F (0°C) for more
than 60 minutes must be discarded.
9. When handling batteries, be wary of electrostatic charge.
Electrostatic discharges can damage the electronic
protection system and the battery cells. Avoid electrostatic
charging and never touch the battery poles.

6
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
READTHEOPERATOR'S
MANUAL(S) – Read, understand,
and follow all instructions in the
user manual(s) before attempting
to assemble and operate.
SAFETY ALERT – Indicates a
precaution, a warning, or a danger.
WEAR EYE PROTECTION –
For protection against injury, wear
safety goggles.
Symbols SymbolsDescriptions Descriptions
HOT SURFACE – To reduce the
risk of injury or damage, avoid
contact with any hot surface.
Indoor use only. Only use battery
charger indoors.
WET CONDITIONS ALERT –
Do not expose to rain or use in
damp locations.

7
KnowYourCordlessHighVolumeInator
Read the owner’s manual and safety instructions carefully before operating the cordless high volume inator. Compare the
illustration below to the cordless high volume inator in order to familiarize yourself with the location of the various controls and
adjustments. Save this manual for future reference.
*Initial no-load voltage, when fully charged, peaks at 24 volts; nominal voltage under typical load is 21.6 volts.
Technical Data
Motor................................................................................150 W
Battery Voltage*...........................................................24 V D.C.
Battery Capacity................................... See page 13 for battery
.......................................................... options and specications
Battery Runtime Max ........................... See page 13 for battery
.......................................................... options and specications
Charge Time Max ................................ See page 13 for battery
.......................................................... options and specications
Working Air Pressure Max ........................ 0.65 PSI, 0.04 BAR
..............................................................(Ination time varies by item)
Air Pressure Max ....................................... 0.7 PSI, 0.05 BAR
Air Speed Max ....................................................... 188.8 MPH
Air Flow Max .............................................................. 36 CFM
Ination Adapter Diameters .......................... 0.17 in (4.3 mm)
....................................................................... 0.19 in (4.8 mm)
.......................................................................... 0.5 in (13 mm)
Weight (without battery) ..................................... 1 lb (0.46 kg)
1. Small Adapter
2. Medium Adapter
3. Large Adapter
4. Deation Port
5. Ination Port
6. ON/OFF Trigger
7. Battery Compartment
1
2
7
3
4
5
6
SOLD SEPARATELY Battery + Charger options available at sunjoe.com
24VBAT
24VBAT-LTE 24VBAT-LT 24VCHRG-QC 24VCHRG-DPC

8
Unpacking
Carton Contents
• Cordless high volume inator
• Ination adapters (x3, attached)
• Manual with registration card
NOTE: In order to operate this cordless high volume inator
you will need iON+ 24V System batteries and chargers.
See page 13 for battery options and specications, or visit
sunjoe.com.
1. Carefully remove the high volume inator and check to
see that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return the unit to the store. Please
call the Snow Joe®+ Sun Joe®customer service center at
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use your new cordless
high volume inator. The packaging is made of recyclable
materials. Properly dispose of these materials in
accordance with local regulations.
IMPORTANT! The equipment and packaging material are
not toys. Do not let children play with plastic bags, foils,
or small parts. These items can be swallowed and pose a
suocation risk!
Battery Pack Operation
The equipment is powered by a lithium-ion battery. The battery
pack is completely sealed and maintenance free.
Battery Charge Level Indicator
The battery pack is equipped with a push button for checking
the charge level. Simply press the push button to read o the
battery charge level from the LEDs of the battery indicator:
• All 3 level monitoring LEDs are lit: Battery charge level
is high.
• 2 level monitoring LEDs are lit: Battery charge level is
decreasing. Stop work as soon as possible.
• 1 level monitoring LED is lit: Battery is at. Stop work
IMMEDIATELY and charge the battery. Otherwise the
battery’s service life will be greatly shortened.
NOTE: If the charge level button does not appear to be
working, place the battery pack on the charger and charge as
needed.
Immediately after using the battery pack, the charge level
button may display a lower charge than it will if checked a few
minutes later. The battery cells “recover” some of their charge
after resting.
Charger Operation
mWARNING! Charge only iON+ 24V lithium-ion battery
packs with its compatible iON+ 24V lithium-ion quick charger.
Other types of batteries may cause personal injury and
damage. To reduce the risk of electric shock, do not allow
water to ow into the charger's AC/DC plug.
When to Charge the iON+ 24V
Lithium-iON Battery
NOTE: The iON+ 24V lithium-ion battery packs do not develop
a "memory" when charged after only a partial discharge.
Therefore, it is not necessary to run down the battery pack
before inserting the charger plug.
• Use the battery charge indicator lights to determine when to
charge your iON+ 24V lithium-ion battery pack.
• You can "top-o" your battery pack's charge before starting
a big job or after a long day of use.
Charging the Battery
1. Push the push lock button on the battery to pull it out of the
equipment (Fig. 1).
In order to operate this cordless high volume inator you will
need an iON+ 24V System battery and charger. See page
13 for battery and charger options and specications, or for
more information visit sunjoe.com.
TOOL ONLY
BATTERY + CHARGER SOLD SEPARATELY
Charge level button
The battery is at 30% capacity
and requires charging
The battery is at 60% capacity
and requires charging soon
The battery is at full capacity
Light IndicatorsLights
In order to operate this cordless high volume inator you will
need an iON+ 24V System battery and charger. See page
13 for battery and charger options and specications, or for
more information visit sunjoe.com.
TOOL ONLY
BATTERY + CHARGER SOLD SEPARATELY

9
2. Depending on your Snow Joe®+ Sun Joe®charger
model, how to recharge your lithium-ion battery will vary.
You may either insert your 24-volt battery into the
24VCHRG-QC Quick Charger (sold separately) or the
24VCHRG-DPC Dual Port Charger (sold separately)
(Figs. 2 – 3).
3. The battery indicator LEDs will illuminate one by one
during the charging process. Unplug the charger
immediately when the 3 LEDs are all illuminated.
4. The 24VCHRG-QC Quick Charger (sold separately) and
the 24VCHRG-DPC Dual Port Charger (sold separately)
are also equipped with additional charging indicating
lights which will indicate the charging status (Figs. 2 – 3).
mCAUTION! FIRE HAZARD. When disconnecting the
charger from the battery, be sure to unplug the charger from
the outlet rst, then disconnect the charger from the battery.
mWARNING! This charger does not automatically turn o
when the battery is fully charged. Please take care not to leave
the battery plugged into the charger. Switch o or unplug the
charger at the mains when charging is complete.
5. Timely recharging of the battery will help prolong the
battery's life. You must recharge the battery pack when
you notice a drop in the equipment's power.
IMPORTANT! Never allow the battery pack to become fully
discharged as this will cause irreversible damage to the
battery.
6. When charging is complete, remove the battery from the
charger by pulling the push lock button and sliding the
battery backward to unlock it from the charger.
Assembly
This high volume inator requires no assembly in order to be
used. Any of the three adpaters may be used for specic tasks.
Attaching the Adapters
This high volume inator is equipped with three inator
adapters. It is recommended to leave them connected, as
disconnecting the adapters may make them easier to lose.
1. To attach an adapter to the inator end, align the notches
on the high volume inator nozzle with the slots on the
adapter of your choice and slide together. Twist the
adapter to lock into place (Fig. 4).
Fig. 1
Push lock
button
Fig. 2 Battery pack
24VCHRG-QC
quickcharger
(Sold separately)
red
Charging
green
Fully
Charged
Fig. 3 Battery pack
24VCHRG-DPC
dual port charger
(Sold separately)
red
Charging
green
Fully
Charged

10
2. To attach an adapter to the deator end, simply snap the
adapter into place (Fig. 5).
Operation
In order to operate this cordless high volume inator you will
need an iON+ 24V System battery and charger. See page
13 for battery and charger options and specications, or for
more information visit sunjoe.com.
TOOL ONLY
BATTERY + CHARGER SOLD SEPARATELY
mWARNING! Do not use any attachments or accessories
not recommended by the manufacturer of this high
volume inator. The use of attachments or accessories not
recommended can result in serious personal injury.
mWARNING! The high volume inator is capable of
inating to 0.7 PSI, 0.05 BAR. To avoid over ination,
carefully follow instructions on items to be inated.
Never exceed recommended pressures.
mCAUTION! Do not leave items to be inated unattended
while high volume inator is in use. These items can burst and
could cause serious injury.
Adapter Functions (Fig. 6)
• The small adapter (0.17 in) can be used on smaller air
valves to inate items like beach balls, children's toys,
and pool inatables. The adapter can be used to deate
vacuum compression bags.
• The medium adapter (0.19 in) is ideal for inating and
deating air matresses, inatable pools, and rafts.
• The large adapter (0.5 in) is ideal for high-volume inatables
like bounce houses and boats.
Starting + Stopping
1. Slide the battery into the battery compartment until it
clicks to lock it into position (Fig. 7).
2. Select and assemble the appropriate adapter for the job.
Insert the nozzle of the adapter into the air port on the
object you wish to inate and deate (Fig. 4).
3. To turn the high volume inator ON, press the ON/OFF
trigger once. To stop, press the ON/OFF button once more
(Fig. 8).
Fig. 4
Notch
Slot
Fig. 5
Large adapter
Small adapter Medium
adapter
Fig. 6
Fig. 7
Battery
Battery
compartment

11
4. When the item is fully inated or deated, turn the unit o,
remove it from the air port, and close the port.
NOTE: Since most high volume inatable's require very low
pressure, this inator does not have an air pressure gauge, it is
designed to inate to the correct "feel".
Storage
1. Examine the cordless high volume inator thoroughly for
worn, loose, or damaged parts. Should you need to repair
or replace a part, contact an authorized Snow Joe®+
Sun Joe®dealer or call the Snow Joe®+ Sun Joe®
customer service center at 1-866-SNOWJOE
(1-866-766-9563) for assistance.
2. Remove the battery from the cordless high volume inator
before storing.
3. Store the high volume inator in a dry, well-ventilated
place that is inaccessible to children. Keep away from
corrosive agents.
Cleaning And Maintenance
mWARNING! Do not at any time let brake uids,
gasoline, petroleum based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can damage,
weaken or destroy plastic which can result in serious personal
injury.
Cleaning
• Keep the ventilation slots of the machine clean to prevent
overheating of the engine.
• Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt.
• If the dirt does not come o use a soft cloth moistened with
soapy water.
• Never use solvents such as petrol, alcohol, ammonia water,
etc. These solvents may damage the plastic parts.
Maintenance
Our machines have been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper machine care and
regular cleaning.
NOTE: Snow Joe®+ Sun Joe®will not be held responsible for
any damage or injuries caused by repair of the high volume
inator by an unauthorized person or by mishandling of the
high volume inator.
Spare parts may be ordered online at sunjoe.com or via phone
by contacting the Snow Joe®+ Sun Joe®customer service
center at 1-866-SNOWJOE (1-866-766-9563).
Avoid using solvents when cleaning plastic parts. Most plastics
are susceptible to damage from various types of commercial
solvents and may be damaged by their use. Use clean cloths
to remove dirt, dust, oil, grease, etc.
Disposal
Should your appliance need replacement after extended
use, do not dispose of it with the household refuse, but in an
environmentally safe way.
Waste produced by electrical machine items should
not be handled like normal household rubbish. Please
recycle where recycle facilities exist. Check with your
local authority or retailer for recycling advice.
Troubleshooting
• If the high volume inator does not function, check the
battery and make sure it is charged.
• If the battery does not charge, check the charger adapter
and the charger adapter cable are connected correctly.
Remove the battery pack and allow it to cool down to room
temperature.
• If there is no pressure, check the adapter and make sure it
is well tted.
• If the inator operated but article does not inate, make
sure you are using the correct adapter. Clean the adapter
and check if the adapter is well tted.
Battery Caution + Disposal
Always dispose of your battery pack according to federal,
state, and local regulations. Contact a recycling agency in your
area for recycling locations.
mCAUTION! Even discharged battery packs contain
some energy. Before disposing, use electrical tape to cover the
terminals to prevent the battery pack from shorting,
which could cause a re or explosion.
mWARNING! To reduce the risk of injury or explosion,
never burn or incinerate a battery pack even if it is damaged,
dead, or completely discharged. When burned, toxic fumes
and materials are emitted into the surrounding atmosphere.
Fig. 8
ON/OFF trigger

12
1. Batteries vary according to device. Consult your manual
for specic information.
2. Install only new batteries of the same type in your product
(where applicable).
3. Failure to insert batteries in the correct polarity, as
indicated in the battery compartment or manual, may
shorten the life of the batteries or cause batteries to leak.
4. Do not mix old and new batteries.
5. Do not mix Alkaline, Standard (Carbon-Zinc), or
Rechargeable (Nickel Cadmium, Nickel Metal Hydride, or
Lithium-Ion) batteries.
6. Do not dispose of batteries in re. The cell of the battery
may explode.
7. Batteries should be recycled or disposed of as per state
and local guidelines.
Service + Support
• High volume inator service must be performed only
by qualied repair personnel. Service or maintenance
performed by unqualied personnel may result in a risk of
injury.
• When servicing an high volume inator, use only identical
replacement parts. Follow instructions in the cleaning and
maintenance section of this manual. Use of unauthorized
parts or failure to follow maintenance instructions may
create a risk of shock or injury.
• If your Sun Joe® cordless high volume inator requires
service or maintenance, please call the Snow Joe®+
Sun Joe®customer service center at 1-866-SNOWJOE
(1-866-766-9563).
Model + Serial Numbers
When contacting the company or reordering parts, you will
need to provide the model and serial numbers of your product.
These are found on the decal axed to the housing or handle
of your cordless compressor. Copy these numbers into the
space provided below.
Record the following numbers from the housing or handle of your
new product: Model #:
Serial #:
24V-AJV-CT

13
Optional Accessories
mWARNING! ALWAYS use only authorized Snow Joe®+ Sun Joe®replacement parts and accessories. NEVER use
replacement parts or accessories that are not intended for use with this cordless high volume inator. Contact Snow Joe®+
Sun Joe®if you are unsure whether it is safe to use a particular replacement part or accessory with your cordless high volume
inator. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.
NOTE: Accessories are subject to change without any obligation on the part of Snow Joe®+ Sun Joe®to provide notice of such
changes. Accessories can be ordered online at sunjoe.com or via phone by contacting the Snow Joe®+ Sun Joe®customer
service center at 1-866-SNOWJOE (1-866-766-9563).
Accessories Item Model
iON+ 24V 1.3 Ah Lithium-Ion Battery
Battery Charge Time Max:
Charge times vary by charger. See website for details.
Battery Runtime Max: 15 min
24VBAT-LTW
iON+ 24V 2.0 Ah Lithium-Ion Battery
Battery Charge Time Max:
Charge times vary by charger. See website for details.
Battery Runtime Max: 20 min
24VBAT-LTE
iON+ 24V 4.0 Ah Lithium-Ion Battery
Battery Charge Time Max:
Charge times vary by charger. See website for details.
Battery Runtime Max: 45 min
24VBAT
iON+ 24V Lithium-Ion Battery Quick Charger 24VCHRG-QC
1
2
3
4

14
NOTES

15 R4_01282020
SNOW JOE®+ SUN JOE®CUSTOMER PROMISE
OUR WARRANTY:
Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in material or workmanship when used
for ordinary household use for a period of two years from the date of purchase by the original, end-user purchaser when purchased
from Snow Joe or from one of Snow Joe’s authorized sellers with proof of purchase. Because Snow Joe is unable to control the quality
of its Products sold by unauthorized sellers, unless otherwise prohibited by law, this Warranty does not cover Products purchased from
unauthorized sellers. If your Product does not work or there’s an issue with a specic part that is covered by the terms of this Warranty,
Snow Joe will elect to either (1) send you a free replacement part, (2) replace the Product with a new or comparable product at no
charge, or (3) repair the Product. How cool is that!
This Warranty gives you specific legal rights, and you may also have other rights which vary from State to State.
PRODUCT REGISTRATION:
Snow Joe strongly encourages you to register your Product. You can register online at snowjoe.com/register, or by printing and
mailing in a registration card available online from our website, or calling our Customer Service Department at 1-866-SNOWJOE
(1-866-766-9563), or by e-mailing us at [email protected]. Failure to register your Product will not diminish your warranty
rights. However, registering your Product will allow Snow Joe to better serve you with any of your customer service needs.
WHO CAN SEEK LIMITED WARRANTY COVERAGE:
This Warranty is extended by Snow Joe to the original purchaser and original owner of the Product.
WHAT IS NOT COVERED?
This Warranty does not apply if the Product has been used commercially or for non-household or rental applications. This Warranty also
does not apply if the Product was purchased from an unauthorized seller. This Warranty also does not cover cosmetic changes that do
not aect performance. Wearing parts like belts, augers, chains and tines are not covered under this Warranty, and can be purchased
at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).
ABOVE ALL ELSE, Snow Joe, LLC (“Snow Joe”) is dedicated to you, our customer. We strive to make your experience as pleasant as
possible. Unfortunately, there are times when a Snow Joe®, Sun Joe®, or Aqua Joe®product (“Product”) does not work or breaks under
normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we have a Limited Warranty
(“Warranty”) for our Products.

sunjoe.com