Sunna Design Sol EVERGEN M Series User manual

SOLAR LIGHT USER MANUAL
EVERGEN M SERIES
Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
Document: 81902_MANUAL_SOL_EverGen_RevD

EVERGEN M SERIES USER MANUAL
2Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
N
N
OTE
OTE
IMPORTANT
Keep your product order informaon. You will need it during setup.
The EverGen lighng system must be acvated aer assembly and installaon using
the EverGen Setup App. Otherwise, the light will not turn on and an addional site
visit will be required.
To complete acvaon:
1. Download the EverGen Setup App from the iOS App Store or Google Play store and
ensure you have a compable mobile device.
2. Use the signup tab to create an account.
3. A vericaon email will be sent to the email address you used to create the account.
Open the email and verify your account.
4. Switch from the signup page to the login page and enter your email and password.
5. Once inside the EverGen Setup App workspace, enter your order number
(ORDXXXXXX).
6. Go to the locaon of the EverGen lighng system, connect to the light and follow the
Setup App to acvate.
If you do not have wireless internet access onsite, use the app to
download product informaon for your order before travelling to the
oine site. Acvaon can then take place onsite without a wireless
signal. Contact us for best pracces for working in remote areas.
EverGen rmware may be periodically released to improve
performance. Firmware updates are managed by the app during the
inial connecon. Updates are mandatory and the process takes
about 45 seconds.
N
N
OTE
OTE
N
N
OTE
OTE
This installaon and instrucon manual provides installaon instrucons for the Sol EverGen Series solar LED lighng
systems. The enre contents of this manual should be thoroughly reviewed and understood prior to installing this
equipment. Do not discard this manual, as it contains complete installaon instrucons.
To ensure proper operaon of this equipment, it is important that the equipment be used only for its intended
purpose. Any use of this equipment for purposes other than those intended will void all warranes.

EVERGEN M SERIES USER MANUAL
WARNINGS AND PRECAUTIONS
3
Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
Warnings and Precauons
The following symbols indicate important safety
warnings and precauons throughout this manual.
They are dened as follows:
NOTE suggests opmal condions
under which the equipment will
operate eecvely and safely, or
provides addional informaon to
the reader.
CAUTION indicates that damage
to equipment may result if the
instrucons are not followed.
WARNING indicates that serious
bodily harm or death may result
from failure to adhere to the
precauons.
Warranty Disclaimer
This manual will familiarize you with the features,
operaon standards, and installaon of Sol's EverGen
M Series. Failure to comply with the use, storage,
maintenance, installaon or placement instrucons
detailed in this manual could void the warranty.
Standards
Perform all installaon, wiring, and maintenance in
conformance with local building and electrical codes.
Adherence to the Naonal Electrical Code (NEC) is
mandatory. Non-adherence to code may void the
warranty.
Safety and Usage Precauons
W
W
A
A
RNI
RNI
N
N
G
G
Do not install poles without
EverGen systems and luminaire(s).
Baeries are shipped fully charged.
Use extreme cauon when handling
the baeries as they are capable
of generang hazardous short-
circuit currents. Remove all jewelry
(bracelets, metal-strap watches,
etc.) before aempng to handle
the baeries.
Solar modules produce DC
electricity when exposed to light
and can, therefore, produce an
electrical shock or burn. To render
solar modules inoperave, remove
them from sunlight, or fully cover
their front surface with an opaque
material.
Before liing any heavy or bulky
equipment, ensure the load is
secured so moving parts do not
shi, and that it can be lied as far
as needed without back strain or
loss of grip. Installaon may require
more than one person.
Unl the system is ready for
startup, keep the baery fuse
out of the fuse holder. Ensure the
equipment is not powered during
installaon and wiring of the
system.
Recheck all completed wiring for
proper polarity prior to energizing
the system.
N
N
OTE
OTE
Changes or modicaons to Sol
equipment not expressly approved
by Sol could void the user's
authority to operate the equipment.
WWAARNIRNINNGG
N
N
OTE
OTE
C
C
AUTION
AUTION

EVERGEN M SERIES USER MANUAL
TABLE OF CONTENTS
4Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
Table of Contents
Warnings and Precauons .................................................................................................................................... 3
Warranty Disclaimer ................................................................................................................................................. 3
Standards .................................................................................................................................................................. 3
Safety and Usage Precauons ................................................................................................................................... 3
Introducon ......................................................................................................................................................... 5
Components ............................................................................................................................................................. 5
System ...................................................................................................................................................................... 5
Posioning the Light ................................................................................................................................................. 6
Tools and Equipment ................................................................................................................................................ 6
Assembly .............................................................................................................................................................. 7
1. Assemble Solar Panel(s) ...................................................................................................................................... 7
2. Assemble Solar Panel Mount .............................................................................................................................. 8
3. Aach Solar Panel to Solar Panel Frame ............................................................................................................. 8
4. Connect Tenon Adapter to Solar Panel Mount ................................................................................................. 10
5. Assemble Baery Box ....................................................................................................................................... 12
6. Connect Solar Panel and Fixture Cables to the EMS ......................................................................................... 14
7. Assemble Integrated Arm (OPTIONAL) ............................................................................................................. 16
8. Assemble Baery Cables ................................................................................................................................... 18
Installaon ......................................................................................................................................................... 19
1. Aach Liing Straps .......................................................................................................................................... 19
2. Orient and Install System .................................................................................................................................. 20
3. Installing Systems with Integrated Arm (OPTIONAL) ........................................................................................ 21
4. Install Fixture..................................................................................................................................................... 23
5. Direct Arm Installaon ...................................................................................................................................... 24
6. Davit Arm Installaon ....................................................................................................................................... 27
7. Baery Installaon ............................................................................................................................................ 30
8. Final Assembly .................................................................................................................................................. 30
Commissioning ................................................................................................................................................... 31
Wiring Diagram .................................................................................................................................................. 32
Maintenance & Product Care .............................................................................................................................. 33
Fuse Replacement .................................................................................................................................................. 33
Troubleshoong ................................................................................................................................................. 34
Warranty ............................................................................................................................................................ 35

EVERGEN M SERIES USER MANUAL
INTRODUCTION
5
Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
Introducon
Components
System
There are several opons available for the EverGen M Series. Pictured below are examples of one and two panel
systems with integrated xture arms.
C
DETAIL C
D
DETAIL D
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
4 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
02/03/2017
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
80871
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
C
DETAIL C
D
DETAIL D
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
4 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
02/03/2017
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
80871
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
One panel, small baery box system Two panel, medium baery box system
SOLAR PANEL
1 OR 2
PANEL PAN (OPTIONAL)
1 OR 2
BATTERY
1 TO 4
TENON ADAPTER
BATTERY BOX WITH EMS
SMALL, MEDIUM OR LARGE
LIGHT FIXTURE CABLE
1 OR 2
BATTERY CABLE KIT
FOR 1 TO 4 BATTERIES
(MAIN CABLE SHOWN)
LIGHT FIXTURE
1 OR 2
SOLAR PANEL MOUNT
1 OR 2 PANEL
(2 PANEL SHOWN)
HARDWARE KIT
FUSES
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
3 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
COPYRIGHT © 2012
ALL RIGHTS RESERVED. NO PART OF THIS
DOCUMENT MAY BE REPRODUCED STORED IN A
RETRIEVAL SYSTEM, OR TRANSMITTED IN ANY
FORM,
PROPRIETARY
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
12/02/2014
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
81264
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
SOLAR PANEL
1 OR 2
PANEL PAN (OPTIONAL)
1 OR 2
BATTERY
1 TO 4
TENON ADAPTER
BATTERY BOX WITH EMS
SMALL, MEDIUM OR LARGE
LIGHT FIXTURE CABLE
1 OR 2
BATTERY CABLE KIT
FOR 1 TO 4 BATTERIES
(MAIN CABLE SHOWN)
LIGHT FIXTURE
1 OR 2
SOLAR PANEL MOUNT
1 OR 2 PANEL
(2 PANEL SHOWN)
HARDWARE KIT
FUSES
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
3 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
COPYRIGHT © 2012
ALL RIGHTS RESERVED. NO PART OF THIS
DOCUMENT MAY BE REPRODUCED STORED IN A
RETRIEVAL SYSTEM, OR TRANSMITTED IN ANY
FORM,
PROPRIETARY
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
12/02/2014
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
81264
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
SOLAR PANEL
1 OR 2
PANEL PAN (OPTIONAL)
1 OR 2
BATTERY
1 TO 4
TENON ADAPTER
BATTERY BOX WITH EMS
SMALL, MEDIUM OR LARGE
LIGHT FIXTURE CABLE
1 OR 2
BATTERY CABLE KIT
FOR 1 TO 4 BATTERIES
(MAIN CABLE SHOWN)
LIGHT FIXTURE
1 OR 2
SOLAR PANEL MOUNT
1 OR 2 PANEL
(2 PANEL SHOWN)
HARDWARE KIT
FUSES
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
3 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
COPYRIGHT © 2012
ALL RIGHTS RESERVED. NO PART OF THIS
DOCUMENT MAY BE REPRODUCED STORED IN A
RETRIEVAL SYSTEM, OR TRANSMITTED IN ANY
FORM,
PROPRIETARY
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
12/02/2014
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
81264
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
SOLAR PANEL
1 OR 2
PANEL PAN (OPTIONAL)
1 OR 2
BATTERY
1 TO 4
TENON ADAPTER
BATTERY BOX WITH EMS
SMALL, MEDIUM OR LARGE
LIGHT FIXTURE CABLE
1 OR 2
BATTERY CABLE KIT
FOR 1 TO 4 BATTERIES
(MAIN CABLE SHOWN)
LIGHT FIXTURE
1 OR 2
SOLAR PANEL MOUNT
1 OR 2 PANEL
(2 PANEL SHOWN)
HARDWARE KIT
FUSES
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
3 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
COPYRIGHT © 2012
ALL RIGHTS RESERVED. NO PART OF THIS
DOCUMENT MAY BE REPRODUCED STORED IN A
RETRIEVAL SYSTEM, OR TRANSMITTED IN ANY
FORM,
PROPRIETARY
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
12/02/2014
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
81264
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
SOLAR PANEL
1 OR 2
PANEL PAN (OPTIONAL)
1 OR 2
BATTERY
1 TO 4
TENON ADAPTER
BATTERY BOX WITH EMS
SMALL, MEDIUM OR LARGE
LIGHT FIXTURE CABLE
1 OR 2
BATTERY CABLE KIT
FOR 1 TO 4 BATTERIES
(MAIN CABLE SHOWN)
LIGHT FIXTURE
1 OR 2
SOLAR PANEL MOUNT
1 OR 2 PANEL
(2 PANEL SHOWN)
HARDWARE KIT
FUSES
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
3 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
COPYRIGHT © 2012
ALL RIGHTS RESERVED. NO PART OF THIS
DOCUMENT MAY BE REPRODUCED STORED IN A
RETRIEVAL SYSTEM, OR TRANSMITTED IN ANY
FORM,
PROPRIETARY
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
12/02/2014
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
81264
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT

EVERGEN M SERIES USER MANUAL
INSTALLATION
6Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
Tools and Equipment
Tools Required
Quick Reference for Fastener Torques (all values for lubricated threads)
Recommended Equipment
Bolt/Screw Size Torque (in-lbs) Torque (-lbs)
1/4" 64 5
3/8" 201 17
5/8" 936 78
Baery Bolt 50 4
a. 3/8" Ratchet
b. 6" Extension for 3/8" Ratchet
c. Sockets: 3/8”, 7/16”, 9/16”, 15/16” Deep Socket,
3/16” Hex Bit
d. 15/16" Wrench
e. Flush Cut Pliers
f. Torque Wrench capable of 0-100-lbs
g. Cordless Drill with ¼” Drill Bit
h. Ear Protecon
i. Bucket Truck and/or Crane Truck
j. Saw Horses or elevated working surfaces
a. EverGen Installaon Kit (82644RevA):
• Three (3) Liing Straps
• MC4 Disconnect Tool
Posioning the Light
1Make sure that the installaon locaon for
the product has an unobstructed view of
the sun’s path.
2Also, note that the posion of the sun will
vary throughout the year, being at its lowest
point relave to the horizon in winter
months.
3Orient the solar panel(s) towards the
equator (towards South in the Northern
Hemisphere, towards North in the Southern
Hemisphere).
4If using a magnec compass, be sure to
take into account the installed locaon’s
magnec declinaon (the dierence
between true north and the direcon a
compass needle points in a given locaon).
Point panels South if in
Northern Hemisphere
Point panels North if in
Southern Hemisphere
S
N

EVERGEN M SERIES USER MANUAL
ASSEMBLY
7
Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
5 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
1Place solar panel(s) glass side down on to clean cardboard (solar panel packaging) on a at, stable surface.
Assembly
The product should be assembled on the ground before being installed on a pole.
1. Assemble Solar Panel(s)
TAKE CARE NOT TO DROP ANY MATERIALS ONTO THE BACK OF THE SOLAR
PANELS DURING THE PRODUCT ASSEMBLY AS THE SOLAR PANELS CAN BE
DAMAGED BY ACCIDENTAL IMPACT.
C
C
AUTION
AUTION
CLICK!
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
6 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
2For systems with two (2) solar panels, connect one (1) cable from each of the panels so that they are in
series. Upon successful connecon, there will be an audible click.

EVERGEN M SERIES USER MANUAL
ASSEMBLY
8Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
2. Assemble Solar Panel Mount
!
THREADED
HOLE IN
SOLAR
PANEL
FRAME
!GREASE!
!
OK
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
7 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM,
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
3. Aach Solar Panel to Solar Panel Frame
1For two panel systems, ensure panels are pushed together and ush prior to, during, and aer bolt
ghtening.
!
THREADED
HOLE IN
SOLAR
PANEL
FRAME
!GREASE!
!
OK
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
7 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM,
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
2Align mount holes with threaded holes in solar panel frame(s).
1Place solar panel mount onto frame(s) of solar panel(s). Ensure that the solar panel mount grommet hole
is facing the solar panel juncon box(es).

EVERGEN M SERIES USER MANUAL
ASSEMBLY
9
Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
4Once bolts are torqued, install grommets as shown below.
STRAIN
RELIEF
FEATURE
SINGLE PANEL
CABLE TIES
CABLE TIES
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
8 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
3Install four (4) (single solar panel) or eight (8) (two solar panels) supplied 1/4"-20 bolts through solar panel
mount slots and into threaded holes in solar panel frame(s) and ghten to 5-lbs (64 in-lbs.).
!
THREADED
HOLE IN
SOLAR
PANEL
FRAME
!GREASE!
!
OK
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
7 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM,
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
2Apply grease to solar panel mount bolt threads.
CLICK!
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
6 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT

EVERGEN M SERIES USER MANUAL
ASSEMBLY
10 Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
STRAIN
RELIEF
FEATURE
SINGLE PANEL
CABLE TIES
CABLE TIES
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
8 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
5Strain relieve the solar panel cables to the solar panel mount frame feature(s) and near the juncon
box(es) using the provided cable es.
4. Connect Tenon Adapter to Solar Panel Mount
3/8"-16
THREADED
HOLES
TENON
ADAPTER
LARGE CLEARANCE
HOLES
TOP
!GREASE!
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
9 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
1Idenfy top of tenon adapter. There are two larger clearance holes through the tenon adapter near the
top. Orient the two (2) 3/8”-16 threaded holes in the tenon adapter as shown.

EVERGEN M SERIES USER MANUAL
ASSEMBLY
11
Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
2Note orientaon and rotaon of tenon adapter once more. Ensure the two (2) 3/8”-16 threaded holes are
facing outwards as indicated.
3Place tenon adapter between panel mount anges as shown.
4
5
Align tenon adapter to holes in solar panel mount anges.
Insert two (2) 5/8”-11 bolts with at washers through clearance holes.
6
7
8
Apply grease to threads of two 5/8”-11 bolts.
Install supplied at washers and lock washers to connect the tenon adapter and solar panel mount anges.
Finger ghten supplied nuts.
Conrm correct orientaon of tenon adapter.
3/8"-16
THREADED
HOLES
TENON
ADAPTER
LARGE CLEARANCE
HOLES
TOP
!GREASE!
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
9 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
THIS IS CRITICAL TO PREVENT IRREVERSIBLE DAMAGE TO BOLT THREADS.
C
C
AUTION
AUTION

EVERGEN M SERIES USER MANUAL
ASSEMBLY
12 Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
3/8"-16 BOLT
!GREASE!
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
10 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
5. Assemble Baery Box
1Take o baery box door by removing the four (4) 1/4”-20 bolts.
2Orient the baery box so that the face with the six (6) holes lines up with the six (6) threaded holes of the
solar panel mount and tenon adapter.
3/8"-16 BOLT
!GREASE!
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
10 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT

EVERGEN M SERIES USER MANUAL
ASSEMBLY
13
Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
L
!GREASE!
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
11 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
3/8"-16 BOLT
!GREASE!
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
10 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
3Using one (1) of the supplied 3/8"-16 bolts with greased threads, secure the baery box into place on the
tenon adapter by threading bolt through the baery box into corresponding hole in the tenon adapter.
4Install ve (5) remaining 3/8"-16 bolts to complete aaching the baery box to the tenon adapter and
solar panel mount.
5
6
Torque all 3/8"-16 bolts to 17 -lbs (201 in-lbs) taking care not to strip the threads in the tenon adapter.
Then torque tenon adapter 5/8”-11 bolts to secure tenon adapter to solar panel mount and solar panel
assembly to 78 -lbs.

EVERGEN M SERIES USER MANUAL
ASSEMBLY
14 Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
L
!GREASE!
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
11 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
6. Connect Solar Panel and Fixture Cables to the EMS
1Route the two (2) unconnected solar panel cables into baery box with enough slack to easily connect to
the EMS.
2Route the end of the xture cable that has a two (2) posion connector and ring terminal into the baery
box with enough slack to easily connect to the EMS. For systems with two xtures, repeat for the second
xture cable while using the xture splier adapter.
3Take the ground wire from the EMS and place it onto the grounding lug followed by the ground wire from
the xture cable.
4Thread supplied 1/4"-20 nut onto ground lug grease and ghten to 5 -lbs (64 in-lbs).
GROUND
LUG
EMS
GROUND
WIRE
FIXTURE
2-POSITION
CONNECTOR
GROUND
WIRE
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
12 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
COPYRIGHT © 2012
ALL RIGHTS RESERVED. NO PART OF THIS
DOCUMENT MAY BE REPRODUCED STORED IN A
RETRIEVAL SYSTEM, OR TRANSMITTED IN ANY
FORM,
PROPRIETARY
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
!GREASE!
DO NOT CONNECT SOLAR PANELS
TO THE EMS AT THIS TIME.
C
C
AUTION
AUTION

EVERGEN M SERIES USER MANUAL
ASSEMBLY
15
Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
7Coil remainder of xture cable wire outside of the baery box and secure temporarily to solar panel mount
unl product has been installed onto the pole.
CABLE
TIE
GROMMET
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:24
-
EVERGEN MANUAL IMAGES
3 OF 3
82064-2
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/30/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
FIXTURE CABLE
EMS CABLE
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
A
EVERGEN MANUAL IMAGES
13 OF 13
82064
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
11/28/2016
05/27/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82053
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
5Connect xture cable connector to EMS connector observing the keying feature. There will be an audible
"click" upon successful connecon.
6Where the cables enter the baery box, install a cable e around all the cables on the inside of the box
and ghten.

EVERGEN M SERIES USER MANUAL
ASSEMBLY
16 Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
3
4
Place integrated arm into the tenon adapter taking care not to pinch the xture cable.
Tighten set screws on the tenon adapter to keep the integrated arm in place while liing.
FIXTURE CABLE
ROUTING
INTEGRATED
ARM
SET SCREWS
NOTES
1 TYPE YOUR NOTES IN HERE
2 FEEL FREE TO MOVE/RESIZE THIS TABLE
REV ECO # DESCRIPTION DATE DRAWN BY
MATERIAL SEE PART MATERIAL
FINISH N/A
FINISH
SPEC
N/A
COLOR N/A
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:24
-
EVERGEN MANUAL IMAGES
1 OF 4
82064-3
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
06/16/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
FIXTURE CABLE
ROUTING
INTEGRATED
ARM
SET SCREWS
NOTES
1 TYPE YOUR NOTES IN HERE
2 FEEL FREE TO MOVE/RESIZE THIS TABLE
REV ECO # DESCRIPTION DATE DRAWN BY
MATERIAL SEE PART MATERIAL
FINISH N/A
FINISH
SPEC
N/A
COLOR N/A
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:24
-
EVERGEN MANUAL IMAGES
1 OF 4
82064-3
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
06/16/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
7. Assemble Integrated Arm (OPTIONAL)
1
2
Route xture cable(s) through tenon adapter.
Insert xture cable(s) into the integrated arm as indicated by the arrows.

EVERGEN M SERIES USER MANUAL
ASSEMBLY
17
Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
5Rotate the assembly so that it rests on the boom edge(s) of the solar panel(s) and the edge of the tenon
adapter. Avoid scratching these surfaces by placing the assembly on cardboard.
NOTES
1 TYPE YOUR NOTES IN HERE
2 FEEL FREE TO MOVE/RESIZE THIS TABLE
REV ECO # DESCRIPTION DATE DRAWN BY
MATERIAL SEE PART MATERIAL
FINISH N/A
FINISH
SPEC
N/A
COLOR N/A
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
-
MANUAL IMAGES, EVERGEN
1 OF 5
82064-1
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/29/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:24
-
EVERGEN MANUAL IMAGES
2 OF 4
82064-3
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
06/16/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
EverGen with Tenon Adapter EverGen with Integrated Arm

EVERGEN M SERIES USER MANUAL
ASSEMBLY
18 Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
8. Assemble Baery Cables
1
2
While at ground level, install baery cable(s) to baery terminals following the color coordinated terminal
ends.
If installed, remove fuse from fuseholder.
CABLE CONNECTIONS VARY DEPENDING ON SYSTEM CONFIGURATION.
In highly corrosive environments, coat all fasteners and ring terminals with
generous amounts of dielectric grease.
N
N
OTE
OTE
N
N
OTE
OTE
3Place the negave (-) wire (BLACK) ring terminal onto the negave (-) terminal of the baery.
4
5
6
7
Apply grease and thread supplied bolts, washers, and lock washers into baery terminal then torque to
50 in-lbs.
Place the posive (+) wire (RED) ring terminal onto the posive (+) terminal of the baery.
Apply grease and thread supplied bolts, washers, and lock washers into baery terminal then torque to
50 in-lbs.
Install terminal covers.
+
-
BLACK
RED
FUSEHOLDER
MAIN BATTERY HARNESS
(2-BATTERY VERSION SHOWN)
!CAUTION!
RISK OF ELECTRICAL SHOCK
IF CONTACTS ARE SHORTED
!GREASE!
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
-
MANUAL IMAGES, EVERGEN
2 OF 5
82064-1
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
05/29/2017
05/29/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064-1
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
PROTECTIVE CAP
COVERING CONNECTOR
FOR SECOND BATTERY
RISK OF ELECTRIC SHOCK.
WWAARNIRNINNGG

EVERGEN M SERIES USER MANUAL
INSTALLATION
19
Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
Installaon
1. Aach Liing Straps
1
2
Install three (3) 4  long straps as guided below through each liing point.
Aach three (3) liing straps to crane hook and li product into place, OR li single solar panel systems by
hand in bucket truck and place on pole tenon.
FOLLOW ALL SAFETY GUIDELINES WHEN OPERATING A CRANE, INCLUDING BUT NOT
LIMITED TO NOT SUSPENDING OBJECTS OVER BYSTANDERS.
LOWER SOLAR PANEL MOUNT
BOTH SIDES
BATTERY BOX
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
-
MANUAL IMAGES, EVERGEN
3 OF 6
82064-1
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
COPYRIGHT © 2012
ALL RIGHTS RESERVED. NO PART OF THIS
DOCUMENT MAY BE REPRODUCED STORED IN A
RETRIEVAL SYSTEM, OR TRANSMITTED IN ANY
FORM
PROPRIETARY
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/29/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
-
MANUAL IMAGES, EVERGEN
4 OF 6
82064-1
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
9/08/15
05/29/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
82064
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
C
C
AUTION
AUTION
DO NOT DROP ANYTHING ONTO THE SOLAR PANELS.
Installaon kit available for order.
N
N
OTE
OTE
N
N
OTE
OTE

EVERGEN M SERIES USER MANUAL
INSTALLATION
20 Sol by Sunna Design | 990 Biscayne Boulevard, Oce 701, Miami, FL 33132, USA | 1.800.959.1329 | customerservice@solarlighng.com
2. Orient and Install System
1
2
3
Once product is placed onto pole, orient solar panel(s) towards the equator (south in Northern
Hemisphere).
Make sure that the area between the solar panel(s) and direct sunlight is unobstructed.
Tighten two (2) installed 3/8"-16 set screws in tenon adapter to pole tenon and torque to 17 -lbs
(201 in-lbs.). Do not exceed the specied torque to avoid stripping the threads in the tenon adapter.
THIS IS CRITICAL TO ENSURE PRODUCT PERFORMANCE AND TO MAINTAIN
BATTERY WARRANTY.
CC
USE AS DRILL
GUIDE FOR
1/4" HOLE
!GREASE!
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
TITLE
B
1:16
-
MANUAL IMAGES, EVERGEN
5 OF 5
82064-1
SHEET
SIZE REVISION
SCALE
DRAWING NO
CAD REFERENCE
250 Bay Street
Victoria, BC Canada V9A 3K5
Tel [250] 380-0052
Fax [250] 380-0062
CHANGES SHALL BE INCORPORATED
ELECTRONICALLY BY THE DESIGN AUTHORITY
PDM MAINTAINED DATA
PROPRIETARY
COPYRIGHT © 2012 ALL RIGHTS RESERVED. NO
PART OF THIS
DOCUMENT MAY BE REPRODUCED
STORED IN A
RETRIEVAL SYSTEM, OR
TRANSMITTED IN ANY
FORM
ORIGINALLY DESIGNED BY
ORIGINALLY DRAWN BY
CHECKED BY DATE
DATE
DATE
Ben Jolie
Ben Jolie
02/03/2017
05/29/2017
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
INTERPRET DIMENSIONS AND TOLERANCES
PER ASME Y14.100-2000
TOLERANCES APPLY AS SHOWN BELOW
DECIMALS SURF FINISH ANGLES
.X
.XX
.XXX
.XXXX
± .1
± .01
± .005
± .0005
63 1
INCHES
THIRD ANGLE PROJECTION
DOC # DATE
21/12/11 57012 B
DOC REVISION
80871
ALL COMPONENTS AND PROCESSES TO BE ROHS COMPLIANT, CERTIFICATE REQUIRED WITH INITIAL SHIPMENT
C
C
AUTION
AUTION