Sunny Health & Fitness EVO-FIT SF-B2969 User manual

EVO-FIT UPRIGHT TRAINING BIKE
SF-B2969
USER MANUAL
IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions.
Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE
CONTACTED US: [email protected] or 1-877-90SUNNY (877-907-8669).

1
IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this equipment
correctly. It is important to read this entire manual before assembling and using the equipment. Safe
and effective use can only be achieved if the equipment is assembled, maintained and used properly.
It is your responsibility to ensure that all users of the equipment are informed of all warnings and
precautions.
1. Before starting any exercise program, you should consult your physician to determine if you have
any medical or physical conditions that could put your health and safety at risk, or prevent you
from using the equipment properly. Your physician’s advice is essential if you are taking
medication that affects your heart rate, blood pressure or cholesterol level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop
exercising if you experience any of the following symptoms: pain, tightness in your chest,
irregular heartbeat, shortness of breath, lightheadedness, dizziness or feelings of nausea. If you
do experience any of these conditions, you should consult your physician before continuing with
your exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet.
To ensure safety, the equipment should have at least 2 feet (60 CM) of free space all around it.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of
the equipment can only be maintained if it is regularly examined for damage and/or wear and
tear.
6. Always use the equipment as indicated. If you find any defective components while assembling
or checking the equipment, or if you hear any unusual noises coming from the equipment during
exercise, discontinue use of the equipment immediately and do not use until the problem has
been rectified.
7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may become
entangled in the equipment.
8. Do not place fingers or objects into the moving parts of the equipment.
9. The maximum weight capacity of this unit is 300 pounds (135 KG).
10.The equipment is not suitable for therapeutic use.
11.To avoid bodily injury and/or damage to the product or property, proper lifting and moving is
required.
12.Your product is intended for use in cool, dry conditions. You should avoid storage in extreme
cold, hot or damp areas as this may lead to corrosion and other related problems.
13.This equipment is designed for indoor and home use only, it is not intended for commercial use!

2
EXPLODED DIAGRAM

3
PARTS LIST
No.
Description
Spec.
Qty.
No.
Description
Spec.
Qty.
1
Console
1
48
Motor
1
2
Screw
M5*10L
8
49
Screw
M5*12L
2
3
Screw
ST3.5*20L
2
50
Flat Washer
Ф5.5*Ф12*2T
2
4
Handlebar Foam
STR φ23*5T*570L
2
51
Belt Cover L
1
5
Hand Pulse
2
52
Belt Cover R
1
6
End Cap
2
53
Screw
ST4.2*16L
6
7
Handlebar
φ25.4*1.6T*1260L
1
54
Decorative Ring
2
8
Hand Pulse Cable
550L
1
55
Crank Cover
2
9
Upright Tube Cover
1
56L/R
Pedal
2
10
Handlebar Post
1
57
Belt
1
11
Sensor Wire 1
950L
1
58
Pulley
φ289
1
12
Cover
1
59
Rubber Washer
1
13
Flat Washer
φ8*φ14*2T
1
60
Screw
ST3.9*35L
7
14
Spring Washer
φ8.5*φ13.5*2.5T
9
61
Screw
ST2.9*8L
12
15
T Shaped Knob
M8
1
62
Magnet Seat
1
16
Bottle Holder
1
63
Screw
M8*P1.25*55L
1
17
Screw
M5*16L
3
64
Flat Washer
φ8*φ19*2T
1
18
Flat Washer
φ8*φ19*2T
2
65
Nylon Nut
M8
2
19
Screw
M8*20L
4
66
Motor Supporter
1
20
Washer
φ8*φ19*2T
6
67
Spring
1
21
Main Frame
1
68
Screw
M5*10L
2
22
Sensor Wire 2
1300L
1
69
Idler Bar
1
23
Spring Knob
M16
1
70
Flat Washer
φ8*φ22*1T
1
24
Bushing
1
71
Spring
1
25
Seat Post
1
72
Screw
M6*10L
1
26
Knob
7/16’’
1
73
Flat Washer
Ф6.5*Ф13*2T
1
27
Seat Slide Cover L
1
74
Idler Wheel
1
28
Seat Slide Cover R
1
75
Wavy Washer
φ10.2*φ13*0.3T
1
29
Seat
1
76
Flywheel
Φ260*3.5KG
1
30
End Cap
2
77
Bearing
6300 2RS
1
31
Seat Slider
1
78
Sleeve
2
32
Bolt
7/16’’
1
79
Small Pulley
Ф30*J8
1
33
Front Stabilizer
1
80
Hex Nut
3/8’’
4
34
End Cap
2
81
Nut
3/8’’
2
35
Screw
ST2.9*8L
2
82
Bearing
6003
2
36
Screw
M8*25L
4
83
Flat Washer
φ30*φ34*0.8T
1
37
Rear Stabilizer
1
84
One-way
Bearing
1
38
Screw
ST4.2*19L
2
85
Wavy Washer
Ф17.5*Ф22*0.3T
1
39
End Cap
2
86
Bearing
6900
2
40
Sensor Supporter
1
87
Flywheel Axle
130L
1
41
Bearing Housing
2
88
Adaptor
1200L
1
42
Open Face Bearing
2
89
Sensor Wire 3
150L
1
43
Locking Nut –Right
15/16’’
1
90
DC Cable
1050L
1
44
Crank
190W*170L
1
91
Spanner
S=13,15,19
1
45
Locking Nut –Left
7/8’’
1
92
Allen Wrench
S=6
1
46
Washer
35*23*2T
1
93
Iron Core Wire
1
47
Hex Nut
7/8’’
1

4
HARDWARE PACKAGE
Ordering Replacement Parts (U.S. and Canadian Customers only)
Please provide the following information in order for us to accurately identify the part(s) needed:
✓The model number (found on cover of manual)
✓The product name (found on cover of manual)
✓The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the front
of the manual)
Please contact us at [email protected] or 1- 877 - 90SUNNY (877-907-8669).

5
ASSEMBLY INSTRUCTIONS
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [email protected] or 1-877-90SUNNY (877-
907-8669).
STEP 1:
Remove the preassembled 4 Screws (No.
36), 4 Spring Washers (No. 14) and 4
Washers (No. 20) from Front & Rear
Stabilizers (No. 33 & 37) using Allen
Wrench (No. 92).
Attach Front & Rear Stabilizers (No. 33
& 37) to Main Frame (No. 21) with 4
Screws (No. 36), 4 Spring Washers (No.
14) and 4 Washers (No. 20).Tighten and
secure with Allen Wrench (No. 92).
STEP 2:
Put the pedal straps into the 2 Pedals (No.
56L/R). Attach the 2 Pedals (No. 56L/R)
to the Crank (No. 44) by Spanner (No.
91).
NOTE: Make sure to attach the Left Pedal
(No. 56L), marked (L), to the Left Crank
(No. 44). It should be tightened counter-
clockwise. Make sure to attach the Right
Pedal (No. 56R), marked (R), to the Right
Crank (No. 44). It should be tightened
clockwise.
Attaching the Pedals (No. 56L/R) to the
wrong Crank (No. 44) or turning them the
wrong direction will damage the Crank
(No. 44).

6
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [email protected] or 1-877-90SUNNY (877-
907-8669).
STEP 3:
Attach the Seat (No. 29) to the Seat Slider
(No. 31) by Spanner (No. 91).
Insert the Seat Post (No. 25) to the Main
Frame (No. 21). Adjust to the desired
height. Insert and tighten the Spring Knob
(No. 23) to secure.
STEP 4:
NOTE: Do not cut any wires when
inserting the Handlebar Post (No. 10) into
the Main Frame (No. 21).
Insert the Handlebar Post (No. 10) into
the Upright Tube Cover (No. 9). Move
the Upright Tube Cover (No. 9) higher.
Connect the Sensor Wire 1 (No. 11) with
Sensor Wire 2 (No. 22). Put all wires into
the Main Frame (No. 21). Insert the
Handlebar Post (No. 10) into the Main
Frame (No. 21) with 4 Screws (No. 19), 4
Spring Washers (No. 14), 2 Flat Washer
(No. 18) and 2 Washer (No. 20) using
Allen Wrench (No. 92).
Move the Upright Tube Cover (No. 9)
lower so it snaps into the Main Frame (No.
21).

7
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [email protected] or 1-877-90SUNNY (877-
907-8669).
STEP 5:
NOTE: Do not to pinch or cut any wires when
attaching the Handlebar (No. 7) into the
Handlebar Post (No. 10).
The upper end of the Iron Core Wire (No. 93) is
attached to console plate (A). Tie the lower end
of the Iron Core Wire (No. 93) and the Hand
Pulse Cables (No. 8). Insert the Iron Core Wire
(No. 93) and Hand Pulse Cables (No. 8) into the
hole on the Handlebar Post (No. 10). Untie the
upper end of the Iron Core Wire (No. 93).Pull
out the Iron Core Wire (No. 93) and Hand Pulse
Cables (No. 8) from the hole on console plate
(A).
Attach the Handlebar (No. 7) to the Handlebar
Post (No. 10). Fix with the T Shaped Knob (No.
15), Spring Washer (No. 14), Flat Washer (No.
13) and Cover (No. 12). You can discard the
Iron Core Wire (No. 93) now.
STEP 6:
NOTE: Do not cut any wires when attaching the
Console (No. 1) to Main Frame (No. 21).
Remove the preassembled 4 Screws (No. 2) on
the back of console (No. 1) by Spanner (No. 91).
Connect the 2 Hand Pulse Cables (No. 8) and
1 Upper Cable (No. 11) with cables from
Console (No. 1) respectively. Put all wires into
the hole on console plate (A).
Attach the Console (No. 1) to console plate (A)
with 4 Screws (No. 2). Tighten and secure with
Spanner (No. 91).

8
We value your experience using Sunny Health and Fitness products. For assistance with parts or
troubleshooting, please contact us at [email protected] or 1-877-90SUNNY (877-
907-8669).
STEP 7:
Remove the preassembled 2 Screws
(No. 17) on the right side on the
Handlebar Post (No. 10), then attach the
Bottle Holder (No. 16) to Handlebar
Post (No. 10) with 2 Screws (No. 17).
Tighten and secure with Spanner (No.
91).
STEP 8:
Connect the Adaptor (No. 88) to the
Main Frame (No. 21).
Assembly is now complete!

9
ADJUSTMENT GUIDE
ADJUSTING THE LEVEL
If the bike is not level, turn the dials on the End
Caps (No. 39) to adjust. Turn counter-clockwise
to raise, and turn clockwise to lower.
ADJUSTING THE SEAT
The Seat (No. 29) of this bike is fully adjustable
as it moves Up, Down, Fore (forward), Aft
(backward).
To adjust the height of the Seat Post (No. 25),
loosen and pull the Spring Knob (No. 23)
outward, then raise or lower the Seat (No. 29) to
the desired height. Once adjusted, re-insert and
tighten the Spring Knob (No. 23) to secure the
Seat Post (No. 25) in place.
To adjust the Seat (No. 29) back and forth,
loosen the Knob (No. 26), then slide the Seat
Slider (No. 31) to the desired position. Once
positioned, tighten the Knob (No. 26) to secure
the Seat Slider (No. 31) in place.
MOVING THE BIKE
To move the bike, stand at the front of the bike
so that you’re directly in front of the Handlebar
(No. 7). Firmly grasp and hold each side of the
Handlebar (No. 7), place one foot on the Front
Stabilizer (No. 33) and tilt the bike towards you
until the transportation wheels on the Front
Stabilizer (No. 33) touch the ground. With the
wheels on the ground, you can transport the bike
to the desired location with ease.