Sunnydaze Decor 73643-FC User manual

ASSEMBLY
1. Place the bottom tier onto the pedestal, twist to lock in place.
2. Place the electric submersible pump in the center of the bottom tier
and run the power cord through the built-in pipe and out the bottom
of the pedestal, ensuring the power cord is beneath the groove on
the bottom of the pedestal.
3. Place the column on the bottom tier, twist to lock in place.
4. Place the middle tier on the column, twist to lock in place.
5. Run the water tube that is built into the topper through the top tier,
twist to lock the topper onto the top tier.
6. Run the water tube through the middle tier, twist to lock the top
assembly to the middle tier.
7. Connect the water tube to the electric submersible pump and install
the pump access cover.
8. Fill the bottom tier with enough water to fully submerge the pump.
NOTE: Additional water will need to be added once the pump
circulates water into the upper tiers.
9. Plug the power cord into a properly grounded GFCI outlet.
Note: When rst used, there may be air in the pump. It may take several minutes for the air to escape and water begins to ow.
Additional water may need to be added once the pump circulates water into the upper tiers.
Page 1 / 273643-43"
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell.
Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with
the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, by email:
[e-mail], or via our contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
10/2020
NOTE: The water tube is built into the
fountain topper. Gently and carefully
uncoil the water tube from inside the
topper. Take care when handling the
water tube; detaching the water tube
from the fountain will damage the
fountain and void the product warranty.
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
 
Fountain Topper 1
Top Tier 1
Middle Tier 1
Column 1
Bottom Tier 1
Pedestal 1
Electric Submersible Pump 1
Pump Access Cover 1
3-TIER FLOWER BLOSSOM WATER FOUNTAIN
73643-FC
Read the assembly instructions carefully and follow the care instructions. Keep these instructions for future reference.



Page 2 / 2

IMPORTANT INFORMATION
• For outdoor use only.
• Some splashing is normal; adjust the flow rate on the pump if the water rate is too high.
• Check the water level frequently to ensure the pump remains fully submerged; never allow the pump to
run dry as it will burn out the motor.
• Only use water in this fountain. Distilled water will help prevent mineral buildup but is not required, avoid
heavily chlorinated water as it may damage the fountain or pump.
• Periodically change the water to keep the fountain and pump clean. Remove scale and buildup regularly.
DO NOT use harmful additives such as bleach, chlorine, etc.
DO NOT use anything abrasive to scrub the fountain.
DO NOT use a pressure washer or abrasive materials to wash the fountain.
• Always shut off the power supply before cleaning and maintaining the fountain and recirculating pump.
• Take care when handling the pump; only pick it up by the body of the pump, never by the power cord.
• During freezing weather, drain the fountain, disconnect the pump and store indoors; allowing ice to form
may damage the fountain in such ways as, but not limited to, the fountain cracking, and/or permanent
pump damage.
TROUBLESHOOTING
• Ensure that the pump is fully submerged and add water if necessary.
• If water is not flowing within several moments of the fountain being plugged in, the pump may have trapped
air which can prevent water from circulating properly. Simply unplug the power supply for a few moments
and plug it back in. Also check the pump and tubing for obstructions.
• If water is not flowing or water is splashing, check the flow control on the body of the pump; it may need to
be adjusted to achieve the desired flow rate.
• If water is not flowing evenly, ensure the fountain is on a smooth, level surface. Add thin, plastic shims (not
included) between tiers to level out water flow.
• Soft surfaces may cause the fountain to become unbalanced. A large stepping stone or paving stone (not
included) is recommended to help ensure the fountain remains evenly balanced.
• Make sure the adapter cable is fully connected to the pump power cable.
• Make sure the power outlet is working; if in doubt about electrical connections, consult a certified electrician.
WARNING!
Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage


10/202073643-43"
If you are still experiencing issues, please contact our customer service team through one of the methods mentioned at
the top of page 1. Please have the item number and order information available to help expedite response time.