Sunnydaze Decor DW-34112 User manual

1
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality
of the items we sell. Replacement parts or products will be sent at our discretion
within the 1-year warranty period. Proof of purchase, with the date of purchase as well
as photos of the merchandise defect, must be provided. Photos are used to determine
the cause of defects and for future quality control.
Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone
at 833-982-1977, by email: [e-mail], or via our
contact us page at https://tiny.cc/SunnydazeContact
Purchase Date: / / Order/Customer Reference Number:
Write down the purchase date and order information to help expedite customer service inquiries.
PREPARATION:
Before beginning assembly, read all warnings and safety precautions.
WARNINGS & CAUTIONS:
WARNINGS:
To reduce the risk of electric shock, only connect the pump to a Ground Fault
Circuit Interrupter (GFCI) outlet.
Do not exceed the voltage shown on the pump.
Always disconnect the pump from the power source before performing any
maintenance or work on the pump, light(s), or any fountain ttings.
Inspect the pump and power cord for damage before installation and
maintenance. If damage is found, the pump should be replaced.
CAUTIONS:
Use a proper power source as indicated on the pump label. Keep the cords
away from high temperatures and heat sources.
Do not lift the pump by its power cord.
Keep the fountain out of reach of children and pets.
Do not let the pump run dry. The pump must be completely submerged for
proper operation and cooling.
Do not pump heated liquids.
Operate with freshwater only. Avoid heavily chlorinated water and water with
high PH levels.
Do not use harsh chemicals such as bleach to clean the fountain or pump.
DW34112
5-STEP ROCK FALLS
INDOOR
TABLETOP FOUNTAIN
WITH LED LIGHTS
DW-34112
Read the assembly instructions carefully and follow the care instructions.
Save these instructions for future reference.
Select a smooth, level surface to place the fountain.
Assemble components of this fountain on a soft, clean surface
to avoid scratching or damaging the nish.
04/2022
Inspect packaging to ensure all
parts are accounted for before
disposing of packing materials.
NOTE: As a result of the manufacturing process, there may be loose
pieces of casting materials inside the fountain.

NOTE: When rst plugged in, there may be air in the pump.
It may take several moments for trapped air to escape, allowing water to ow.
2
NOTE: The water tubing is built into the fountain body. Take care when handling the water tube; detaching
the water tube from the fountain body may damage the fountain and will void the product warranty.
ASSEMBLY:
1. From the access panel in the back of the fountain, locate the pump power
cord, pull it out of the reservoir, and connect the AC adapter.
2. Check that the light cables are rmly connected to the splitters and the
pump.
3. Check that the pump is rmly connected to the water tubing that is built
into the fountain, and the pump is sitting at on the bottom of the reservoir.
4. Slide the pump access panel door onto the back of the fountain.
5. Fill the fountain with enough water to keep the pump fully submerged
during operation, approximately 2.5 cups.
6. Plug the AC adapter into a properly grounded GFCI outlet.
3
TROUBLESHOOTING
• Ensure the pump is fully submerged under water. Add water to the
reservoir as necessary.
• Check to make sure the power outlet is working; consult a certified electrician
if in doubt about electrical connections.
• Check the pump and tubing for obstructions.
• Check the flow control on the body of the pump, as it may need to be adjusted
to achieve the desired flow rate.
• If the lights are not working, ensure the cable is fully connected and the seals
are adequately tightened (do not over-tighten).
• If water is not flowing within several moments of the fountain being plugged in,
unplug the power supply for a few moments and plug it back in. The pump may
have air bubbles in the filter, which can prevent water from circulating properly
and cause excess pump noise.
• Pump noise can be caused by trapped air, low water level, or the pump being
too close to the walls of the fountain. While fully submerged, gently tap the
the pump with your finger to help release trapped air. Check if adding water or
move the pump within the reservoir reduces noise.
USE & CARE
• For indoor use only.
• Keep fountain out of reach of children and pets.
• Keep power cord away from all heat sources. Do not place electrical cords in
areas with high temperatures.
• Check the water level frequently to ensure the pump remains fully submerged;
never allow the pump to run dry as it will burn out the motor.
• Only use water in this fountain; distilled water is recommended to prevent
mineral buildup but is not required.
• Periodically change the water to keep the water, fountain and pump clean.
Remove scale and buildup regularly.
DO NOT use harmful additives such as bleach, chlorine, etc.
DO NOT use anything abrasive to scrub the fountain.
• Always unplug the power supply before cleaning and maintaining the fountain
and the recirculating pump.
• Take care when handling the pump; only pick it up by the body of the pump,
never the power cord.
IMPORTANT INFORMATION
Any modication to the product or failure to follow
recommended care will void the product warranty.