Sunnydaze Decor Ethereal Essence User manual

1
WARRANTY:
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the
quality of the items we sell. Replacement parts or products will be sent at our
discretion within the 1-year warranty period. Proof of purchase, with the date
of purchase as well as photos of the merchandise defect, must be provided.
Photos are used to determine the cause of defects and for future quality control.
Register your warranty at https://tiny.cc/SunnydazeWarranty
If you have any questions, comments or concerns, feel free to contact us by phone
at 888-881-4668, by email: [e-mail], or via our
contact us page at https://tiny.cc/SunnydazeContact
PREPARATION:
Before beginning assembly, read all warnings and safety precautions.
WARNINGS & CAUTIONS:
WARNINGS:
To reduce the risk of electric shock, only connect the pump to a Ground Fault
Circuit Interrupter (GFCI) outlet.
Do not exceed the voltage shown on the pump.
Always disconnect the pump from the power source before performing any
maintenance or work on the pump, light(s) or any fountain ttings.
Inspect the power cord for damage before installation and maintenance. If
damage to the pump is found, it should be replaced.
Purchase Date: / / Order/Customer Reference Number:
Write down the purchase date and order information to help expedite customer service inquiries.
CAUTIONS:
Use a proper power source as indicated on the pump label. Keep the cords
away from high temperatures and heat sources.
Do not lift the pump by its power cord.
Keep the fountain out of reach of children.
Do not let the pump run dry. The pump must be completely submerged for
proper operation and cooling.
Do not pump heated liquids.
Operate with freshwater only. Avoid heavily chlorinated water and water with
high PH levels.
Do not use harsh chemicals such as bleach to clean the fountain or pump.
04/2020DW197106
ETHEREAL ESSENCE
INDOOR TABLETOP
WATER FOUNTAIN
WITH LED LIGHT
DW-081
Read the assembly instructions carefully and follow the care instructions.
Save these instructions for future reference.
Select a smooth, level surface to place the fountain.
Assemble components of this fountain on a soft, clean surface
to avoid scratching or damaging the nish.

3
TROUBLESHOOTING
• Ensure the pump is fully submerged under water. Add water to the
basin as necessary.
• Check to make sure the power outlet is working; if in doubt about
electrical connections, consult a certified electrician.
• Check the pump and tubing for obstructions.
• Check the flow control on the body of the pump as it may need to be
adjusted to achieve the desired flow rate.
• If the light is not working, ensure the cables are fully connected and the
seal is adequately tightened (do not over-tighten).
• If water is not flowing within several moments of the fountain being
plugged in, unplug the power supply for a few moments and plug it
back in. The pump may have air bubbles in the filter, which can prevent
water from circulating properly.
USE & CARE
• For indoor use only.
• Keep fountain out of reach of children and pets.
• Keep power cord away from all heat sources. Do not place electrical
cords in areas with high temperatures.
• Check the water level frequently to ensure the pump remains fully
submerged; never allow the pump to run dry as it will burn out the motor.
• Only use water in this fountain; distilled water is recommended to
prevent mineral buildup.
• Periodically change the water to keep the water, fountain and pump
clean. Remove scale and buildup regularly.
DO NOT use harmful additives such as bleach, chlorine, etc.
DO NOT use anything abrasive to scrub the fountain.
• Always shut off the power supply before cleaning and maintaining the
fountain and the recirculating pump.
• Take care when handling the pump; only pick it up by the body of the
pump, never the power cord.
Any modication to the product or failure to follow recommended care
will void the product warranty.
IMPORTANT INFORMATION
2
NOTE: The water tubing is built into the fountain. Take care when handling the water tube; detaching the
water tube from the fountain will damage the fountain and void the product warranty.
ASSEMBLY:
1. Connect the shorter cable on the pump to the LED light cord that is inside
the fountain. If the cords are already connected, check connection and
tighten the plastic collar. Connect the pump to the water tube and place
the pump inside the fountain.
2. Run pump power cable out the back of the fountain. Align the cable
with the groove in the access panel cover, as shown.
3. Twist the access panel cover to secure it to the back of the fountain.
4. Fill the fountain with enough water to keep the pump fully submerged
during operation.
5. Connect the AC adapter to the power cord and plug it into a properly
grounded GFCI outlet.
2
1
4
5
Note: When rst used, there may be air in the pump.
It may take several minutes for trapped air to escape, allowing water to ow.
3