Sunnydaze Decor GSI-298 User manual

SLATE INDOOR TABLETOP OR WALL-MOUNT WATER
FOUNTAIN WITH LED LIGHT
GSI-298
Read assembly instructions carefully and follow the care instructions. Save these instructions for future reference.
Select a smooth, level surface to place the fountain.

SPQ50048 Page 1 / 201/2020
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we
sell. Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof
of purchase, with the date of purchase as well as photos of the merchandise defect, must be provided.
Photos are used to determine the cause of defects and for future quality control. Register your warranty at
www.serenityhealth.com/warranty/
If you have any questions, comments or concerns, feel free to contact us by phone at 888-881-4668, by email:
[e-mail], or via our contact us page at www.SerenityHealth.com/contact-us/
Purchase Date: / / Order/Customer Reference Number:
Note: When rst used, there may be air trapped in the pump. It may take several minutes for the air to escape and water begins to ow.
CONNECT
CONNECT
A
B
C
D
E
F
G
H
Ensure all parts are
accounted for before
disposing of packaging.
TABLETOP ASSEMBLY
1. Clip the rubber end of Finger Light (B) to the underside
of Lid (A).
2. Keeping the light cord on the backside of Fountain
Body (C), attach Lid (A) to Fountain Body (C) using 2x
Bolt (D) and 2x Washers (E).
3. Run the light cord behind the preinstalled bracket on
the backside of the fountain body; this will prevent the
light cord from being damaged if the fountain is wall-
mounted.
4. Connect Finger Light (B) to Pump (E).
5. Connect Pump (E) to the water tube that is on the
backside of Fountain Body (C).
6. Making sure the light and pump power cord are run
out the groove in the back of Basin (G), gently place
the assembled components onto the basin and secure
using 2x Bolt (D) and 2x Washers (E).
7. Gently place the Decorative Stones (H) onto the bottom
of the fountain body.
8. Fill the fountain with enough water to keep the pump
fully submerged during operation; approximately 1/2
gallon.
9. Firmly connect the AC Adapter to the pump power
cable and plug it into a properly grounded GFCI outlet.
NOTE: The water tubing is built into the fountain body. Take care when handling the water tube;
detaching the water tube from the fountain will damage the fountain and void the product warranty.
  
ALid 1
BFinger Light 1
CFountain Body 1
DBolt 4
EWasher 4
FElectric Submersible Pump 1
GBasin 1
HDecorative Stones 1PK
  
IWall Screw 5
JWall Anchor 1
KWall-Mount Bracket 1
LCord Channel 1
MCord Cover 2

OPTIONAL CORD PROTECTORS
1. Tape the cord channel against the wall where the cord
will go down the wall.
2. Mark the top and bottom hole with a pencil. Remove the
tape and cord channel from the wall.
3. Drill starter holes (1/4 inch or 6mm) on the pencil marks.
4. Gently hammer two wall anchors into the starter holes.
5. Align the cord channel with the wall anchors and secure
it using two wall screws.
6. Put the cord into the Cord Channel. Cover the Channel
with one or both cords cover.
TROUBLESHOOTING
• Ensure that the pump is fully submerged and add water if necessary.
• Check the pump and tubing for obstructions.
• If water is not flowing within several moments of the fountain being plugged in, unplug the power supply for a few moments and plug it back
in; the pump may have air trapped inside it which can prevent water from circulating properly.
• Adjust the flow control on the body of the pump to achieve the desired flow rate.
• If water is not flowing evenly, it may be due to the porous nature of the slate material. Moisten the entire slate surface beneath the downspout
to even out water flow.
• If the light is not working, ensure the cable is fully connected and the seal is adequately tightened (do not over-tighten).
• Check to make sure the power outlet is working; if in doubt about electrical connections, consult a certified electrician.
USE & CARE
• FOR INDOOR USE ONLY.
• Keep fountain out of reach of children and pets.
• Keep power cord away from all heat sources. Do not place electrical cords in areas with high temperatures.
• Check the water level frequently to ensure the pump remains fully submerged; never allow the pump to run dry as it will burn out the motor.
• Only use water in this fountain; distilled water is recommended to prevent mineral buildup.
• Periodically change the water to reduce scale and buildup — clean components regularly for optimal performance and appearance.
DO NOT use harmful additives such as bleach, chlorine, etc.
DO NOT use abrasive materials to scrub the fountain.
• Always shut off the power supply before cleaning and maintaining the fountain and the pump.
• Take care when handling the pump; only pick it up by the body of the pump, never by the power cord.

IMPORTANT INFORMATION
SPQ50048 Page 2 / 201/2020
OPTIONAL WALL-MOUNT:
1. Tape the bottom of the wall-mount bracket on the wall
17.5 inches above where the bottom of the fountain will
rest on the wall. Check to make sure the bracket is level.
2. Mark the holes in the bracket with a pencil. Remove the
tape and bracket from the wall.
3. Drill starter holes (1/4 inch or 6mm) on the pencil marks.
4. Gently hammer three wall anchors into the starter holes.
5. Align the wall-mount bracket with the wall anchors and
secure it using three wall screws.
6. Ensuring the preinstalled bracket on the fountain is
centered over the wall-mount bracket, carefully lower
the fountain onto the wall-mount bracket. Check to make
sure the pump power cord is within the groove on the
backside of the fountain basin.
K
I
J
WARNING!
Manufacturer and seller expressly disclaim any and all liability from personal injury, property damage

inadequate maintenance, or neglect of this product.
J
M
IL
Before wall-mounting, ensure the wall can support the weight of the fountain while it is full of water.