Sunnydaze Decor DW-679 User manual

WARRANTY:
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality
of the items we sell. Replacement parts or products will be sent at our discretion within
the 1-year warranty period. Proof of purchase, with the date of purchase as well as
photos of the merchandise defect, must be provided. Photos are used to determine the
cause of defects and for future quality control.
If you have any questions, comments or concerns, feel free to contact us by phone at
888-881-4668, by email: [email protected], or via our contact
us page at www.SerenityHealth.com/contact-us/
PREPARATION:
Before beginning assembly, read all warnings and safety precautions.
WARNINGS & CAUTIONS:
WARNINGS:
To reduce the risk of electric shock, only connect the pump to a Ground
Fault Circuit Interrupter (GFCI) outlet.
Do not exceed the voltage shown on the pump.
Always disconnect the pump from the power source before performing
any maintenance or work on the pump, light(s) or any fountain ttings.
Inspect the power cord for damage before installation and maintenance.
If damage to the pump is found, it should be replaced.
CAUTIONS:
Use a proper power source as indicated on the pump label. Keep the
cords away from high temperatures and heat sources.
Do not lift the pump by its power cord.
Keep the fountain out of reach of children.
Do not let the pump run dry. The pump must be completely submerged
for proper operation and cooling.
Do not pump heated liquids.
Operate with freshwater only. Avoid heavily chlorinated water and
water with high PH levels.
Do not use harsh chemicals such as bleach to clean the pump.
03/2019DW185059 1
DOUBLE HELIX
WATER FOUNTAIN
WITH LED LIGHT
DW-679
Read the assembly instructions carefully and follow the care instructions. Keep
these instructions for future reference.
Select a smooth, level surface to place the fountain.
Assemble components of this fountain on a soft, clean surface to avoid
scratching or damaging the nish.

Note: When rst used, there may be air in the pump.
It may take several minutes for the air to escape and water begins to ow.
TROUBLESHOOTING
• Ensure that the pump is fully submerged and add water to the basin if
necessary.
• Check to make sure the power outlet is working; if in doubt about electrical
connections, consult a certified electrician.
• Check the pump and tubing for obstructions.
• Check the flow control on the body of the pump as it may need to be adjusted
to achieve the desired flow rate.
• If the light is not working, ensure the cables are fully connected, and the seal
is adequately tightened (do not over-tighten).
• If water is not flowing within several moments of the fountain being plugged in,
unplug the power supply for a few moments and plug it back in; the pump may
have air bubbles in the filter which can prevent water from circulating properly.
IMPORTANT INFORMATION
USE & CARE
• Recommended for outdoor use only. Some splashing is normal; adjust the flow
rate on the pump if the water rate is too high.
• Check the water level frequently to ensure the pump remains fully submerged;
never allow the pump to run dry as it will burn out the motor.
• Only use water in this fountain; distilled water will help prevent mineral buildup
but is not required.
• Periodically change the water to keep the water, fountain and pump clean.
Remove scale and build-up regularly.
DO NOT use harmful additives such as bleach, chlorine, etc.
DO NOT use anything abrasive to scrub the fountain.
DO NOT use a pressure washer.
• Always shut off the power supply before cleaning and maintaining the fountain
and the recirculating pump.
• Take care when handling the pump; only pick it up by the body of the pump,
never the power cord.
• During freezing weather, drain the fountain, disconnect the pump and store
indoors; allowing ice to form will damage the fountain.
Any modication or failure to follow the recommended care
will void the product warranty.
32
Assemble components of this fountain on a soft, clean surface to avoid scratching or damaging the nish.
ASSEMBLY:
1. Connect the electric submersible pump to the tubing that is inside
the fountain.
2. Place the LED light in the basin of the fountain and run the pump
and LED light power cords through the opening in the back of the
fountain.
3. Attach the AC adapter to the LED light cable.
4. Fill the fountain with enough water to keep the pump fully
submerged during operation.
5. Place the splash screen into the fountain basin.
6. Plug the power cords into a properly grounded GFCI outlet.
2
1
3
4
6
5