Sunrise Medical Quickie Rhythm User manual

O w n e r ’ s M a n u a l
Quickie®Rhythm
BC, SC, MPC
Supplier: This manual must be given to the rider of
this wheelchair.
Rider: Before using this wheelchair read this entire manual
and save for future reference.
S E C T I O N
S E C T I O N E N G L I S H
RHYTHM
improving people’s lives

112670 Rev. A 2
RHYTHM
I. INT RODUCTION
USER WARN NG
WARN NG
Attention wheelchair users, do not operate this wheel-
chair without first reading the owner’s manual. f you
do not understand the instructions and warnings of this
owner’s manual please contact your dealer or qualified
technician before operating this Quickie wheelchair.
Failure to do so may result in damage and/or injury.
DEALER/TECHN C AN WARN NG
WARN NG
Attention dealers and qualified technicians, do not oper-
ate or service this wheelchair without first reading this
owners manual. f you do not understand the instruc-
tions and warnings of this owners manual please contact
the Quickie Technical Service Department before oper-
ating and/or servicing this Quickie wheelchair. Failure to
do so may result in damage and/or injury.
WARN NG
n addition, power wheelchairs may contain printed cir-
cuit boards. Careful attention should be given to the
Printed Circuit Board Handling Techniques insert sup-
plied with the chair.
Related Documents
Listed below are additional documents which are referenced in this
owners manual.
• RN T Owners Manual
• RN T OBP Owners Manual
• RN T Omni Owners Manual
SUNR SE L STENS
Thank you for choosing a Quickie wheelchair. We want to hear
your questions or comments about this manual, the safety and
reliability of your chair, and the service you receive from your
Sunrise supplier. Please feel free to write or call us at the address
and telephone number below:
Sunrise Medical
Customer Service De artment
7477 East Dry Creek Parkway
Longmont, Colorado 80503
[phone] or [phone]
FOR ANSWERS TO YOUR QUEST ONS
Your authorized supplier knows your wheelchair best, and can
answer most of your questions about chair safety, use and mainte-
nance. For future reference, fill in the following:
Supplier:_______________________________________________________________
Address: _______________________________________________________________
______________________________________________________________________
Telephone: _____________________________________________________________
Serial #: _______________________________________ Date/Purchased:_________

112670 Rev. A
3
RHYTHM
II . TABLE OF CONTENT S
I. INTRODUCTION ................................................... 2
II. TAB E OF CONTENTS.......................................... 3
III. YOUR CHAIR AND ITS PARTS ............................ 4
IV. NOTICE - READ BEFORE USE.............................. 5
V. EMI (E ECTROMAGNETIC INTERFERENCE)...... 5
A. What is MI................................................................ 5
B. What ffect Can MI Have........................................ 5
C.Sources of MI ........................................................... 6
D.Distance From the Source ......................................... 6
. Immunity Level........................................................... 6
F. Report All Suspected MI Incidents........................... 6
G. MI From Chair ......................................................... 6
VI. GENERA WARNINGS .......................................... 7
A. Notice to User and Attendants ................................. 7
B. Weight Limit............................................................... 7
C.Controller Settings ..................................................... 7
D. MI............................................................................. 7
. Safety Checklist.......................................................... 7
F. Changes & Adjustments............................................. 8
G.When Seated in a Parked Wheelchair........................ 8
H. nvironmental Conditions ......................................... 8
I. Terrain ........................................................................ 8
J. Street Use .................................................................. 8
K. Motor Vehicle Safety.................................................. 8
L. Center of Balance ...................................................... 9
M.Transfers..................................................................... 9
N.Reaching or Leaning................................................... 9
O.Dressing or Changing Clothes ................................... 9
P. Obstacles ................................................................... 9
Q.Driving in Reverse...................................................... 9
R. Ramps, Slopes & Sidehills........................................... 9
S. To Reduce the Risk of Falls, Tip-over
or Loss of Control ..................................................... 10
T. Ramps at Home & Work............................................ 10
U.Wheelchair Lifts ......................................................... 10
V. Curbs & Single Steps.................................................. 10
W.Stairs .......................................................................... 10
X. scalators ................................................................... 10
VII. WARNINGS: COMPONENTS & OPTIONS.......... 11
A. Armrests .................................................................... 11
B. Batteries..................................................................... 11
C.Cushion & Sling Seats................................................. 11
D.Fasteners.................................................................... 11
. Footrests .................................................................... 11
F. Motor Lock ................................................................ 11
G.On/Off Switch ............................................................ 11
H.Pneumatic Tires ......................................................... 11
I. Positioning Belts (Optional) ....................................... 12
J. Push Handles.............................................................. 12
K. Seating Systems .......................................................... 12
L. Upholstery Fabric ...................................................... 12
M.Power Seating ............................................................ 12
N.Assignable Controls ................................................... 12
O.CG Tilt Power Accessory .......................................... 13
P. Power Recline ............................................................ 13
Q.Power Legrest Accessory .......................................... 13
R. Transit Use ................................................................. 13
VIII. SET UP, ADJUSTMENT & USE.............................. 14
Notes ............................................................................. 14
Tools You Will Need ...................................................... 14
Check Out ..................................................................... 14
A. Battery Removal......................................................... 15
B. Folding Backrest......................................................... 15
C.Swing-Away Footrests ............................................... 16
D. levating Legrests (Optional)..................................... 16
. Center Mount Hanger Adjustment............................ 16
F. Joystick and nhanced Display................................... 17
G.Joystick Retractable Mount (Optional)....................... 17
H.Dual-Post Height-Adjustable Armrests (Optional),
Fixed Height Standard ............................................... 17
I. Single Post Height-Adjustable Armrests (Optional)... 18
J. Seat Depth ................................................................. 18
K. Transit Option ............................................................ 18
Seating System Setup................................................ 19
A. A.S.A.P. Seating Adjustment ....................................... 19
B. Seat Pan and Back Size Adjustments.......................... 19
C.Pre-Tilt (Packer Module Only)................................... 19
Seating System Adjustment ..................................... 19
A. Manual Recline Operation.......................................... 19
B. Power Recline Tilt/Lift Operation.............................. 19
IX. OPERATING GUIDE .............................................. 20
A. Performance Control Settings ................................... 20
B. On-Board, DTT, or RN T PC Programmer.............. 20
C.Thermal Roll-Back...................................................... 20
D.Fuses .......................................................................... 20
. VR2 Joystick Assembly ............................................... 21
F. L D Joystick............................................................... 22
G.Color LCD Screen ..................................................... 23
H.Motor Locks............................................................... 24
X. BATTERIES ............................................................. 25
A. Introduction ............................................................... 25
B. Battery Charger ......................................................... 25
C.Acid Burns.................................................................. 25
D.Connecting Batteries in Battery Compartment......... 25
. Charging Batteries...................................................... 26
F. Disposing of Batteries ................................................ 26
XI. MAINTENANCE..................................................... 26
A. Notes ......................................................................... 26
B. Cleaning ..................................................................... 26
C.Storage Tips ............................................................... 26
D.Battery Maintenance .................................................. 27
. Pneumatic Tires ......................................................... 27
F. To Repair or Replace a Tire ....................................... 27
G.Ordering Parts ........................................................... 27
H.Maintenance Chart..................................................... 27
XII. WIRING DIAGRAMS.............................................. 28
XIII. SUNRISE IMITED WARRANTY .......................... 30

112670 Rev. A 4
RHYTHM
II I. OU R CH AI R AN D IT S PARTS
1. Armrest
2. Joystick
3. Seat Pan
4. Front Hanger
5. Caster Tire
6. Foot Plate
7. Backrest
8. Push Handle
9. Free-wheel Release Lever
10. Seat Frame
11. Drive Wheels
12. Base Frame
13. Caster Fork
14. Transit Tie Down (not shown)
III. OUR CHAIR AND ITS PARTS
QUICKIE RH THM
1
23
4
6
5
9
10
11
12
13
7
8
Base Chair User Weight imits*
300 lbs to 400 lbs
*Weight capacity may vary due to options
chosen, refer to appropriate order form.
Drive Wheels
14" x 3"
Tire types: Standard - pneumatic
Option - solid insert
Tilt (Option)*
50° CG Tilt
300 lb capacity
Joystick
Standard - Joystick (right-hand
or left-hand mount, fixed)
Option - swing-away mount
Batteries
(2 deep cycle batteries required to
operate chair)
Option - Group 24 gel or 22NF gel
Battery Charger
Standard - 8 amp off-board
Backrest
Traditional Rehab - Fixed or Folding,
non-recline: 16" - 24"
Option - Fixed w/manual recline:
15", 17", 19"
Option - JAY SPO / ART SPO
Option - Power recline
Seat Frame Dimensions
Frame width:
Traditional Rehab - 12" - 22"
(1" increments)
Seat depth:
Traditional Rehab - 12"-22"
(1" increments)
Seat height:
Traditional Rehab - 17" - 20"
(1" increments)
Seat : Traditional Rehab - Solid seat
Option-cushion: 2" (50mm)
Seats, Upholstery and Style
Standard- A.S.A.P. Seat Frame
(BC, SC only):
Sizes: 16" - 20" wide, 16" - 20" deep
Caster Fork
Standard - Fixed
Footrest
Standard - Swing-away with composite
footplate.
Option - Swing-away tapered (75°) or
swing-away straight (65°), elevating
legrests, angle-adjustable footplate,
extended, toe loops, extension tubes,
solid one-piece, two piece locking
Casters
6" solid
Armrests
Standard - (Rehab) dual post with stan-
dard or full length pad, fixed height,
adjustable flip-back arms (Perfect Fit)
Option - (Rehab) dual post height-
adjustable, height-adjustable with
standard or full length pad, recline
height-adjustable (Perfect Fit)
Standard? 14" Flip back, height adjustable
14" arm pad (BC, SC)
Option- Locking, two-point arm
All features may not be available with some chair
setups or in conjunction with another chair feature.
Please consult your supplier for more information.
Your authorized supplier can also provide you with
more information on accessories.

112670 Rev. A
5
RHYTHM
IV. N OTI CE – RE AD B EFORE USE
A. CHOOSE THE R GHT CHA R & SAFETY
OPT ONS
Sunrise provides a choice of many power wheelchair styles, sizes and
adjustments to meet the needs of the user. However, final selection
of a wheelchair rests solely with you and your health care profession-
al. Choosing the best chair for you depends on such things as:
1. Your size, disability, strength, balance and coordination.
2. Your intended use, and your level of activity.
3. The types of hazards you must overcome in daily use (in
areas where you are likely to use your chair).
4. The need for options for your safety and comfort (such as
positioning belts or special seat systems).
B. ADJUST CHA R TO YOUR AB L TY
You need to work with your doctor, nurse or therapist, and your
supplier, to fit this chair and adjust the controller settings for your
level of function and ability.
C. REV EW TH S MANUAL OFTEN
Before using this chair you, and each person who may assist you,
should read this entire Manual and make sure to follow all instruc-
tions. Review the warnings often, until they are second nature to you.
D.WARN NGS
The word “WARNING” refers to a hazard or unsafe practice that
may cause severe injury or death to you or to other persons. The
“Warnings” are in four main sections, as follows:
1. V — EM
Here you will learn about electromagnetic interference and
how it can affect your chair.
2. V — GENERAL WARN NGS
Here you will find a safety checklist and a summary of risks
you need to be aware of before you ride this chair.
3. V — WARN NGS — COMPONENTS & OPT ONS
Here you will learn about your chair. Consult your supplier
and your health care professional to help you choose the
best set-up and options for your safety.
4. X — BATTER ES
Here you will learn about battery and charger safety, and
how to avoid injury.
Q-NOTE– Where they apply, you will also find “Warnin s” in other
sections of this Manual.
Throughout this owner’s manual and on the wheelchair you will
see the icons listed below to identify warnings and potential haz-
ards. It is important to read and understand all of them and under-
stand them.
WARNING! These warnings must be followed, failure to
do so may cause personal injury or may dam-
age the wheelchair.
PROHIBITED! Prohibited actions must never be performed.
Performing an action that is prohibited can
cause personal injury or may damage the
wheelchair.
Q-NOTE: Q-Notes are informative statements to help
further explain actions, warnings or product
detail.
ESD: lectrostatic Discharge has a potential to
damage printed circuit boards unless handled
correctly. When the SD symbol is shown
throughout the owner manual, use the Proper
Handling Techniques Insert supplied with the
chair to properly handle printed circuit board.
V. EMI (ELECTRO MA GN ET IC INTERFERENCE)
WARN NG
Heed all warnings to reduce the risk of unintended
brake release or chair movement:
1. Beware of the danger from hand-held transceivers.
Never turn on or use a hand-held transceiver while
power to your chair is on. Use extra care if you believe
that such a device may be in use near your chair.
2. Be aware of nearby radio or TV stations, and avoid
coming close to them.
3. If unintended movement occurs, turn your chair off as
soon as it is safe to do so.
A. WHAT S EM ?
WARN NG
1. MI means: electromagnetic ( M) interference (I). MI
comes from radio wave sources such as radio transmitters
and transceivers. (A “transceiver” is a device that both sends
and receives radio wave signals).
2. There are a number of sources of intense MI in your daily
environment. Some of these are obvious and easy to avoid.
Others are not, and you may not be able to avoid them.
3. Powered wheelchairs may be susceptible to electromagnetic
interference ( MI) emitted from sources such as radio sta-
tions, TV stations, amateur radio (HAM) transmitters, two
way radios, and cellular phones.
4. MI can also be produced by conducted sources or electro-
static discharge ( SD).
B. WHAT EFFECT CAN EM HAVE?
WARN NG
1. MI can cause your chair, without warning, to:
• Release its brakes
• Move by itself
• Move in unintended directions
If any of these occurs, it could result in severe injury to you
or others.
2. MI can damage the control system of your chair. This could
create a safety hazard, and lead to costly repairs.

112670 Rev. A 6
RHYTHM V.
4. The following specialty input devices have an unknown effect on
the immunity level because they have not been tested with the
Rhythm and Delphi control system:
WARN NG
ndividuals with physical limitations requiring the use of
a specialty control input device known not to be
immune to 20V/m, or not known, should exercise extra
care around known sources of EM .
WARN NG
There is no way to know the effect on EM if you add
accessories or modify this chair. Any change to your
chair may increase the risk of EM . Parts not specifically
tested or parts from other suppliers have unknown EM
properties.
F. REPORT ALL SUSPECTED EM
NC DENTS
WARN NG
You should promptly report any unintended movement or brake
release. Be sure to indicate whether there was a radio wave source
near your chair at the time. Contact:
Sunrise Medical, Customer Service Department at [phone].
G.EM FROM CHA R
WARN NG
The chair itself can disturb the performance of electromagnetic
fields such as emitted by alarm systems of shops.
C. SOURCES OF EM
WARN NG
The sources of MI fall into three broad types:
1. Hand-Held Transceivers:
The antenna is usually mounted directly on the unit. These include:
• Citizens band (CB) radios
• “Walkie-talkies”
• Security, fire and police radios
• Cellular phones
• Lap-top computers with phone or fax
• Other personal communication devices
Q-NOTE– These devices can transmit si nals while they are on,
even if not in use.
2. Medium-Range Mobile Transceivers:
These include two-way radios used in police cars, fire trucks,
ambulances and taxi cabs. The antenna is usually mounted on the
outside of the vehicle.
3. Long-Range Transceivers:
These include commercial radio and TV broadcast antenna towers
and amateur (HAM) radios. NOTE– The following are not likely to
cause MI problems: Lap-top computers (without phone or fax),
Cordless phones, TV sets or AM/FM radios, CD or tape players.
D.D STANCE FROM THE SOURCE
WARN NG
M energy rapidly becomes more intense as you get closer to the
source. For this reason, MI from hand-held devices is of special
concern. (See C.1 above) A person using one of these devices can
bring high levels of M energy very close to your chair without you
knowing it.
E. MMUN TY LEVEL
WARN NG
1. The level of M is measured in volts per meter (V/m). very
power wheelchair can resist MI up to a certain level. This is
called its “immunity level”.
2. The higher the immunity level, the less the risk of MI. It is
believed that a 20 V/m immunity level will protect the power
wheelchair user from the more common sources of radio
waves.
3. The configuration tested and found to be immune to at least
20 V/m is: Quickie Rhythm power wheelchair with a right-
hand mounted Delphi remote joystick system, 18" seat
width, 18" seat depth, dual post height adjustable armrests,
fixed tapered legrests with one piece solid footplate, and Gp
24 gel cell batteries.
• Breath Control
•Proportional Head
Control
• Tri-Switch Head Array
• Proportional Mini-
Joystick/Chin Control
• Heavy Duty Switched
Joystick
• Buddy Button
• Treadle Switch
• Micro Light
• Ribbon Switch
• Star Board
•Proximity Head Array
• Wafer Board
• Zero Touch Switch
• Penta Switch
• 4-Zero Touch Switch
• Plate Switch
• 5-Zero Touch Switch
• Soft Switch
• Disc Switch
• Grasp Switch
• Wobble Switch

112670 Rev. A
7
RHYTHM
VI . GE NE RA L WARNINGS
WARN NG
Heed all warnings in this section. f you fail to do so a
fall, tip-over or loss of control may occur and cause
severe injury to you or others.
A. NOT CE TO USER AND ATTENDANTS
WARN NG
User
1. Before using this chair, you should be trained in its safe use
by your health care professional.
2. very wheelchair is different. Take the time to learn the feel
of this chair before you begin riding.
3. Be aware that you must develop your own methods for the
safe use of this chair, that are best suited to your level of
function and ability.
4. Have someone help you practice bending, reaching and
transfers until you learn how to do them safely.
5. Never try a new maneuver on your own unless you are sure
it is safe.
6. Get to know the areas where you plan to use your chair.
Look for hazards and learn how to avoid them.
7. Always wear a positioning strap.
8. Do not use a wheelchair if the joystick does not spring back
to the neutral position.
9. Do not use your wheelchair if the joystick boot is ripped or
damaged.
10. Do not try to tip this wheelchair without an attendant pres-
ent.
User and Attendants
1. When transferring the user in or out of the wheelchair never
use the footplate as a platform.
2. Do not lift this wheelchair by any parts that are removable,
doing so may result in damage to the wheelchair or injury to
the user.
3. Never try to stop or slow this wheelchair with the wheel
locks (if applicable). Wheel locks are designed to prevent the
chair from moving when stopped. They are not brakes.
4. Always keep your hands and body parts clear of moving parts
to help prevent injuries.
Attendants
WARN NG
Make sure you heed all warnings and follow all instruc-
tions in each section of this manual. Be aware that
warnings that apply to the user also apply to you.
1. Do not stand or sit on any portion of this wheelchair.
2. You need to work with the user, and the user’s doctor, nurse
or therapist, to develop safe methods best suited to your
abilities and those of the user.
3. To manually push the chair you must release the motor locks.
• Do not engage or disengage motor locks unless power to
the chair is off. In addition, make sure both free wheel
levers are completely pushed in before turning the power
on to ensure the wheelchair can be driven in a straight
forward motion.
• Make sure you have full control over the chair when you
release the motor locks. When you do so the chair will
not have brakes.
• Make sure the chair is on level ground before you release
the motor locks.
NOTE– To release the wheel locks the wheel chair may need to be rocked
back and forth sli htly several times before the lock will release.
4. Propel this chair by the push handles only. They provide
secure points for you to hold the rear of the chair to prevent
a fall or tip-over.
• Check to make sure push handle grips will not rotate or
slip off.
B. WE GHT L M T
WARN NG
1. The user plus items carried should never exceed the total
weight capacity identified on your chair.
2. Never use this chair for weight training if the total weight
(user plus additional weights) exceeds weight capacity.
3. xceeding the weight limit is likely to damage the seat,
frame, or fasteners, and may cause severe injury to you or
others from chair failure.
4. xceeding the weight limit will void the warranty.
C. CONTROLLER SETT NGS
WARN NG
Be aware that you may need to adjust the controller settings of
your chair.
1. Check and adjust the settings every six to twelve months.
2. Consult your supplier to adjust the control settings immedi-
ately if you notice any change in your ability to:
• Control the joystick
• Hold your torso erect
• Avoid running into objects.
D.EM
WARN NG
Read Section V to learn about MI. To reduce the risk of unintend-
ed brake release or chair movement:
1. Never turn on or use a hand-held transceiver while power to
your chair is on. Use extra care if you believe that such a
device may be in use near your chair.
2. Be aware of nearby radio or TV stations, and avoid coming
close to them.
3. If unintended movement or brake release occurs, turn your
chair off as soon as it is safe.
E. SAFETY CHECK-L ST
WARN NG
Before each use of this chair:
1. Make sure the chair operates smoothly. Check for noise,
vibration, or a change in ease of use. (They may indicate low
tire pressure, loose fasteners, or damage to your chair).
• If you detect a problem, make sure to repair or adjust
the chair. Your supplier can help you find and correct the
problem.
2. Make sure batteries are charged. Green lights on charge indi-
cator will light up when charge is full. Yellow lights indicate
battery charge level is getting low. Red lights indicate batter-
ies are in immediate need of charging.

112670 Rev. A 8
RHYTHM VI.
3. When not in use, keep your chair in a clean, dry place.
WARN NG
Extra caution should be used when employing the disc
switch or the proximity head array as control devices.
These two devices are susceptible to malfunction when
wet.
. TERRA N
WARN NG
1. This chair will perform at optimum on firm, even surfaces
such as concrete, asphalt and indoor flooring.
2. Although equipped with suspension, the performance can be
substantially reduced on uneven surfaces and rough terrain.
3. Do not operate the chair on sand, loose gravel or soil. Doing
so may damage wheels, bearings, axles, motors or loosen fas-
teners.
J. STREET USE
WARN NG
In most states, power chairs are not legal for use on public roads.
Be alert to the danger of motor vehicles on roads or in parking lots.
1. Do not operate this wheelchair on any roadways that do not
allow non-motor vehicle traffic.
2. When visibility is limited by either darkness or weather condi-
tions, do not operate the chair on any roadways.
3. It may be hard for drivers to see you. Make eye contact with
drivers before you proceed. When in doubt, yield until you
are sure it is safe.
K. MOTOR VEH CLE SAFETY
Iidentify whether your chair has been manufactured with the
Transit Option installed.
f your chair is not equipped with the Transit Option:
WARN NG
f your chair is not equipped with Transit Option, this
wheelchair does not meet federal standards for motor
vehicle seating.
1. N V R let anyone sit in this chair while in a moving vehicle.
2. ALWAYS secure the rider with proper motor vehicle
restraints. In an accident or sudden stop the rider may be
thrown from the chair. Wheelchair seat belts will not prevent
this, and further injury may result from the belts or straps.
3. N V R transport this chair in the front seat of a vehicle. It
may shift and interfere with the driver.
4. ALWAYS secure this chair so that it cannot roll or shift.
5. Do not use any chair that has been involved in a motor vehi-
cle accident.
f your chair is equipped with the Transit Option:
See section VII-S: “Transit Use” and section VIII-L: “Transit Option”.
F. CHANGES & ADJUSTMENTS
PROH B TED!
Never use non-Quickie parts to replace Quickie provided parts or
make changes to your chair unless authorized by Sunrise. (Doing so
will void the warranty and may create a safety hazard.)
WARN NG
Accessories designed by manufacturers other than
Sunrise, not available through Sunrise order process have
not been tested or approved for use by Sunrise.
1. If you modify or adjust this chair it may increase the risk of a
fall or tip-over.
2. Modifications unauthorized by Sunrise constitutes remanufac-
turing of the wheelchair. This voids the warranty. The user
then assumes all future liability for the wheelchair.
G.WHEN SEATED N A PARKED
WHEELCHA R
WARN NG
1. Always turn off all power to your chair when you are parked,
even for a moment. This will prevent:
• Accidental movement from contact with the joystick by
you or others.
• Unintended brake release or movement from MI
sources. (See Section V)
2. Make sure that persons who help you (for example, store
clerks) are aware of the joystick and do not touch it. If they
do, your chair may move suddenly when you do not expect it.
H.ENV RONMENTAL COND T ONS
WARN NG
Your chair is not designed for use in a heavy rain storm, or in
snowy or icy conditions.
1. Contact with water or excessive moisture can cause an elec-
trical malfunction. The frame, motors and other chair parts
are not water-tight and may rust or corrode from the inside.
To avoid a chair failure:
• Minimize exposure of your chair to rain or very
wet conditions.
• Never take your chair into a shower, tub, pool or sauna.
• Do not use your chair in fresh or salt water (such as at
the edge of a stream, lake, or ocean).
• Make sure battery cover is secure.
• Replace joystick boot if it becomes torn or cracked.
• Make sure all electrical connections are secure.
• Dry the chair as soon as you can if it gets wet, or if you
use water to clean it.
2. Proceed slowly and use extra care if you must operate your
chair on a wet or slick surface.
• When in doubt, have someone help you.
• Do so only if you are sure it is safe.
• Stop if one or both main wheels lose traction. If this
occurs, you may lose control of your chair or fall.
• Never operate your chair on a slope or ramp if there is
snow, ice, water or oil film present.

112670 Rev. A
9
RHYTHM VI.
L. CENTER OF BALANCE
WARN NG
The point where this chair will tip forward, back, or to the side
depends on its center of balance and stability.
The Center Of Balance s Affected By:
1. The seat height and seat angle.
2. A change in your body position, posture or weight distribu-
tion.
3. Using this chair on a ramp or slope.
4. The use of a back pack or other options, and the amount of
added weight.
5. Drive wheel positioning.
To Reduce The Risk Of A Fall Or Tip-Over:
Whenever a condition exists that may change the center of
balance, reduce speed, proceed cautiously, and when in
doubt, always have someone help you.
M. TRANSFERS
WARN NG
It is dangerous to transfer on your own. It requires good balance
and agility. Be aware that there is a point during every transfer
when the wheelchair seat is not below you. To prevent a fall:
1. Always turn off power before you transfer to or from your
chair. If you fail to do so you may touch the joystick and
cause your chair to move when you do not expect it.
2. Make sure motor locks are engaged. This keeps the chair
from moving when you transfer.
3. Work with your health care professional to learn safe methods.
• Learn how to position your body and how to support
yourself during a transfer.
• Have someone help you until you are sure you can do a
safe transfer on your own.
4. Move your chair as close as you can to the seat you are
transferring to. If possible, use a transfer board.
5. Rotate the front casters until they are as far forward as possible.
6. Be careful of the footrests. If you can, remove or swing them
out of the way.
• Never stand on footrests when you transfer. Doing so
may damage them or cause your chair to tip.
• Make sure your feet do not “hang up” or get caught in
the space between the footrests.
7. Make sure armrests do not interfere.
8. Transfer as far back onto the seat surface as you can. This will
reduce the risk that you will miss the seat or fall.
N.REACH NG OR LEAN NG
WARN NG
Reaching or leaning affects the center of balance of your chair. If
done improperly, a fall or tip-over is likely. When in doubt, ask for
help or use a device to extend your reach.
To Reduce the Risk of injury and/or Damage to the Chair:
1. Never reach or lean if you must shift your weight sideways or
rise up off the seat.
2. Never reach or lean if you must move forward in your seat
to do so. Always keep your buttocks in contact with the
backrest.
3. Never reach with both hands (you may not be able to catch
yourself to prevent a fall if you lose your balance).
4. Never try to pick up an object from the floor by reaching down
between your knees.
5. Never put pressure on the footrests while reaching.
6. Never reach or lean over the top of the seat back. This may
damage the backrest and cause you to fall.
F YOU MUST REACH OR LEAN DO SO AT
YOUR OWN R SK.
Remember to:
1. Move your chair as close as you can to the object you wish
to reach.
2. Rotate the front casters until they are as far forward as possi-
ble. This makes the chair more stable.
Q-NOTE– To do this: Move your chair past the object you want to
reach, then back up alon side it. Backin up will rotate the
casters forward.
3. Turn off all power to your chair. If you fail to do so, you may
touch the joystick and cause your chair to move when you
do not expect it.
O.DRESS NG OR CHANG NG CLOTHES
WARN NG
Be aware that your weight will shift if you dress or change clothes
while seated in this chair. To make the chair more stable, rotate the
front casters until they are forward.
P. OBSTACLES
WARN NG
Obstacles you may have to overcome in daily use include door
thresholds, lifts, ramps and hazards such as potholes and broken
pavement. These can damage your chair and may cause a fall, tip-
over or loss of control.
1. Be aware that thresholds are very dangerous. ( ven a small
change in height may stop a caster wheel and cause your
chair to tip). You may need to:
• Remove or cover threshold strips between rooms.
• Install a ramp at entry or exit doors.
2. Keep your eyes moving when you ride; scan the area well
ahead of your chair.
3. Make sure the floor areas where you use this chair are level
and free of obstacles.
Q.DR V NG N REVERSE
WARN NG
Use extra care when you drive your chair in reverse. You may lose
control or fall if one of the rear wheels hits an object.
1. Operate your chair slowly and at an even speed.
2. Stop often and check to make sure your path is clear of
obstacles.
R. RAMPS, SLOPES & S DEH LLS
WARN NG
The center of balance of your chair changes when you are on a
slope.
Q-NOTE– “Slope” includes a ramp or sidehill. Your chair is
less stable when it is at an angle. Never use this
chair on a slope unless your are sure it is safe.
When in doubt, have someone help you.

112670 Rev. A 10
RHYTHM VI.
U.WHEELCHA R L FTS
WARN NG
Wheelchair lifts are used in vans, buses, and buildings to help you
move from one level to another.
1. Always turn off all power to your chair when you are on a
lift. If you fail to do so, you may touch the joystick by acci-
dent and cause your chair to drive off the platform. (Be
aware that a “roll-stop” at the end of the platform may not
prevent this).
2. Make sure there is not a lip or drop-off at the top or bottom
of the platform. These may cause a fall or tip-over. When in
doubt, have someone help you.
3. Always position the user securely in the chair to help prevent
falls while on a lift.
4. Avoid moving forward if a wheel is “hung up” on the lip of
the ramp. Backup, reposition the caster for a more direct
approach. And slowly try again.
V. CURBS & S NGLE STEPS
WARN NG
1. It is recommended to climb and/or descend a curb, single
step, or other obstacle that a ramp or curb cutout is always
used.
2. If you must climb or descend a curb, single step, or other
obstacle that is greater than 2.5", it is recommended to have
a person assist you in doing so.
3. In no case should you try to climb a curb, single step, or
other obstacle greater than 4" high.
4. If you must climb or descend a curb or step alone do so at
your own risk using extreme care and follow the following
procedure:
• Proceed slowly, at a steady speed
• Go as straight up or down as you can over the obstacle.
Never turn when trying to climb or descend and obstacle,
doing so may result in a fall or tip-over.
5. Failure to follow the above procedures may cause:
• A Fall or Tip Over
• Damage to the frame, wheels, axles or other parts, or
loose fasteners.
W. STA RS
PROH B TED!
Never use this chair to go up or down stairs, even with
an attendant. Doing so is likely to cause a fall or tip-over.
X.ESCALATORS
PROH B TED!
Never take this chair on an escalator, even with an
attendant. Doing so is likely to cause a fall or tip-over.
Beware Of:
1. Steep slopes. Do Not use this chair on a slope steeper than
10%. (A 10% slope means: One foot in elevation for every
ten feet of slope length).
2. Wet or slippery surfaces (such as when ice, snow, water or oil
film is present). A loss of traction may cause a fall or tip-over.
3. A change in grade on a slope (or a lip, bump or depression).
These may cause a fall or tip-over.
4. A drop-off at the bottom of a slope. (A drop-off of as small
as 3/4 inch (19 mm) can stop a front caster and cause the
chair to tip forward).
S. TO REDUCE THE R SK OF A FALL, T P-
OVER OR LOSS OF CONTROL:
WARN NG
1. Never use your chair on a slope unless you are sure you can
do so without losing traction.
2. Always go as straight up and as straight down as you can.
• Do not “cut the corner” on a slope or ramp.
• Do not turn or change direction on a slope.
3. Always stay in the center of the ramp. Make sure ramp is
wide enough that you are not at risk that a wheel may roll off
the side.
4. Keep your chair moving at a slow, steady speed. Keep con-
trol over the chair at all times.
• On a descent, do not let your chair accelerate beyond its
normal speed.
• If the chair picks up speed, center the joystick to slow
down or stop.
Q-NOTE– The solid state controller of your chair has a
logic system that will help control your speed
when driving on a slope or uphill.
• If you stop, re-start slowly.
T. RAMPS AT HOME & WORK
WARN NG
Before driving on a ramp, survey the condition of the
ramp. On slippery ramps traction may be reduced caus-
ing your wheelchair to slide.
WARN NG
Make sure ramps meet all Building Codes for your area.
1. For your safety, have a licensed contractor build or remodel
ramp to meet all standards.
2. Q-NOTE– The proper design will vary, depending on
such things as: the length and height of the ramp; the need for
an intermediate platform; landing size; doors, and the direction
of swing, and; whether the ramp includes a turn or angle.
At A Minimum:
1. Open sides of ramp must have side rails to prevent your
chair from going over the edge.
2. Slope must not be steeper than one inch in height for every
one foot of slope length (approximately 10º).
3. Ramp surface must be even, and have a non-skid surface.
4. You may need to add a section at the top or bottom to avoid
a lip or drop-off.
5. Ramp must be sturdy. Add bracing if needed, so ramp does
not “bow” when you ride on it.

112670 Rev. A
11
RHYTHM
VI I. WA RN IN GS: COMPONENTS AND OPTIONS
WARN NG
Note: f you use parts or make changes not authorized
by Sunrise it may create a safety hazard and will void
the Warranty.
A. ARMRESTS
WARN NG
Armrests will not bear the weight of this chair.
PROH B TED!
Never lift this chair by its armrests. They may come
loose or break.
B. BATTER ES
WARN NG
Always wear rubber gloves and safety glasses when you
handle batteries.
PROH B TED!
Never smoke or hold an open flame near batteries.
They are a known explosion hazard.
WARN NG
1. Only deep cycle sealed case construction batteries should
be used in this device.
2. To prevent an acid spill, always keep batteries upright (wet
cell batteries).
3. Read all of section X. Batteries before attempting to change,
or charge batteries.
C. CUSH ONS & SL NG SEATS
WARN NG
1. Standard foam cushions and other body supports are not
designed for the relief of pressure.
2. If you suffer from pressure sores, or if you are at risk that
they will occur, you may need a special seat system or a
device to control your posture.
• Consult your doctor, nurse or therapist to find out if you
need such a device for your well-being.
D.FASTENERS
WARN NG
Many of the screws, bolts and nuts on this chair are special high-
strength fasteners. Use of improper fasteners may cause your chair
to fail.
1. Only use fasteners provided by Sunrise.
2. If fasteners become loose, tighten them immediately.
3. Over- or under-tightened fasteners may fail or cause damage
to chair parts.
•See Section VIII, “Set-Up, Adjustment & Use”, for
proper torque settings.
E. FOOTRESTS
WARN NG
1. At the lowest point, footrests should be at least 2 1/2 inch-
es (65 mm) off the ground. If set too LOW, they may “hang
up” on obstacles you can expect to find in normal use. This
may cause the chair to stop suddenly and tip forward.
2. To avoid a trip or fall when you transfer:
• Make sure your feet do not “hang up” or get caught in
the space between the footrests.
•Avoid putting weight on the footrests, as the chair may
tip forward.
• Remove or swing the footrests out of the way, if possible.
3. The footrest should always be in the down position when
operating the chair.
PROH B TED!
Never lift this chair by the footrests. Footrests detach
and will not bear the weight of this chair. Lift this chair
only by non-detachable parts of the main frame.
F. MOTOR LOCKS
WARN NG
1. Do not engage or disengage motor locks unless power to the
chair is off. In addition, make sure both free wheel levers are
completely pushed in before turning the power on to ensure
the wheelchair can be driven in a straight forward motion.
2. Be aware that the chair will not have brakes when motor
locks are in the free-wheel position.
3. Make sure that the person pushing the chair has full control
when motor locks are disengaged.
4. Make sure that the chair is on level ground when motor
locks are disengaged.
NOTE– To release the wheel locks the wheel chair may need to be rocked
back and forth sli htly several times before the lock will release.
G.ON/OFF SW TCH
WARN NG
1. Never use the ON/OFF switch to stop the chair except in
an emergency. This will result in an abrupt stop, and may
cause you to fall.
2. To slow your chair to a stop, return the joystick to neutral.
H.PNEUMAT C T RES
WARN NG
Proper inflation extends the life of your tires and makes your chair
easier to use.
1. Do not use this chair if any of the tires are under- or over-
inflated. Check weekly for proper inflation level, as listed on
the tire sidewall.
2. Low pressure in a tire may cause the chair to veer to one
side and result in a loss of control.
3. An over-inflated tire may burst.
4. Never use a gas station air pump to inflate a tire. Such
pumps provide air at high volume, and could cause the tire
to burst. To prevent tire damage:
• Use a hand pump (or low volume air pump) to inflate tires.
• Use a tire gauge to check pressure.
5. Driving over sharp objects may cause damage to pneumatic
tires and tubes.

112670 Rev. A 12
RHYTHM VII.
M. POWER SEAT NG
WARN NG
1. Operation
• While driving this wheelchair in the reclined, elevated, or
tilted position use caution.
• Do Not attempt to operate any power seating option
while positioned on an incline.
• Do Not attempt to operate any power seating option
while this wheelchair is in motion.
• Do not attempt to operate the lift or tilt power seating
options around children.
• Through programming it is possible to reverse the direction
of all powered seating functions, ensure you know which
direction your seat is going to move before operating.
2. Reduced Speed Driving (Creep)
This power chair is designed to automatically reduce the
maximum driving speed to a creep mode when certain
power seating limits are reached.
3. Pinch points
Pinch points may occur when operating the powered seating
options on this chair. nsure all hands and body parts are
clear of all power seating components that may result in
pinch points before operating them.
4. Tilting Power Base with Push Handles
Do not attempt to tilt power wheelchairs by pulling down on
the push handles. Power wheelchairs have heavy bases. As
such, attempting to tilt a power wheelchair to traverse obsta-
cles can damage components in the seating system and/or
modular actuators.
5. Remain Clear During Power Accessory Operation
Please stay clear of any powered actuator while the compo-
nent is in motion. Sunrise power mechanisms move over
large ranges of travel. Users should be aware of their sur-
roundings while components are in motion.
6. Maximum User Weight
Do not exceed the weight capacity for your specific
chair/seating system configuration. Doing so could result in
premature failure or injury.
7. Latch Mode
While operating any power seating function in latched mode
use caution. In latch mode, powered seating will not stop until
a reverse command is performed or the end of travel is met.
N. ASS GNABLE CONTROLS
WARN NG
It is possible to assign a function to an input control (buttons, jacks)
of your wheelchair . If controls have been assigned to perform a
dual or alternate function ensure you know what each control
operates. A list of the assigned functions should have been supplied
with the wheelchair if this feature is programmed. Please contact
your dealer or the Quickie Technical Service Department if you do
not receive this information. Failure to do so may result in damage
and/or injury.
. POS T ON NG BELTS (OPT ONAL)
WARN NG
Use a positioning belt only to help support your posture. Improper
use of such belts may cause severe injury or death.
1. Make sure you are not at risk to slide down in the wheelchair
seat. If this occurs, you may suffer chest compression or suf-
focate due to pressure from the belt.
2. A pelvic wedge or a similar device can help keep you from
sliding down in the seat. Consult your health care profes-
sional to find out if you need such a device.
3. The belt must be snug, but must not be so tight that it inter-
feres with breathing. You should be able to slide your open
hand, flat, between the belt and your stomach.
4. Make sure you can easily remove the belt in an emergency.
PROH B TED!
Never use a positioning belt:
• In place of a motor vehicle seat belt. In an accident or
sudden stop you may be thrown from the chair. A posi-
tioning belt will not prevent this, and further injury may
result from the belt.
• As a restraint. A restraint requires a doctor’s order.
• On a user who is comatose or agitated.
J. PUSH HANDLES
WARN NG
1. Push handles provide secure points for an attendant to propel
and control the chair. This helps to prevent a fall or tip-over.
2. Check to make sure push handle grips will not rotate or slip off.
K. SEAT NG SYSTEMS
WARN NG
1. Use of a seating system not approved by Sunrise may alter
the center of
balance of this chair. This may cause a fall or tip-over.
2. Never change the seating system of your chair unless you
consult your supplier first.
3. Never raise your seating system to a height of more than 22"
(measuring from the front of the seat pan to the floor).
L. UPHOLSTERY FABR C
WARN NG
1. Replace worn or torn fabric of seat sling and seat back as
soon as you can. If you fail to do so, the seat may fail and
cause you to fall. Worn fabrics may increase the potential for
a fire hazard.
2. Sling fabric will deteriorate with age and use. Look for fray-
ing, thin spots, or stretching of fabric at rivet holes. Replace
fabric as required.
3. Be aware that washing may reduce flame retardation of the
fabric.

112670 Rev. A
13
RHYTHM VII.
O.CG T LT POWER ACCESSORY
WARN NG
The powered CG Tilt accessory for this chair has a maxi-
mum user weight capacity of up to 400 lbs. Never exceed
this capacity while operating the powered actuator.
P. POWER RECL NE
WARN NG
Pinch Point
Avoid putting hands or fingers near the power recline mechanism
while in operation.
Weight Capacity
The maximum user weight capacity for the power recline is up to
300 lbs. xceeding this weight capacity could lead to injury and/or
permanent damage to the equipment.
Q.POWER LEGREST ACCESSORY
The power legrest accessory for the Rhythm has a maximum user
weight capacity of up to 300 lbs or 400 lbs depending on your chair
configuration. Never exceed this capacity while operating the pow-
ered actuator.
R. TRANS T USE
Refer also to sections VI-K: “Motor Vehicle Safety” and VIII-L:
“Transit Option” for additional transit option and motor vehicle
warnings.
WARN NG
1. If possible and feasible, the rider should transfer to the
original quipment Manufacturer vehicle seat and use the
vehicle restraint.
2. If the wheelchair is used for transport, it must be used in a
forward-facing seating poition.
3. The rider must not weigh more than 300 lbs.
4. Use only with Wheelchair Tie-down and Ocupant Restraint
Systems (WTORS) that have been installed in accordance
with the manufacturer’s instructions and SA J2249.
5. Attach WTORS to securement points in accordance with
the manufacturer’s instructions and SA J2249.
6. Attach occupant restraints in accordance with the
manufacturer’s instructions and SA J2249.
7. nsure hip guides are mounted to lock in place.

112670 Rev. A 14
RHYTHM
VI II . SE T-U P, AD JU STMENT AND USE
TOOLS YOU W LL NEED
1. Basic Tool Kit:
To set-up, adjust and maintain your chair you may need the
following tools:
• Combined Phillips and flat screw driver
• Standard metric wrenches from 8mm - 14mm
•Metric Allen wrenches from 2mm - 5mm
• Imperial wrenches from 1/4" to 9/16"
• Imperial Allen wrenches from 5/64" to 1/4"
You can obtain a multi-purpose tool kit from Sunrise, or buy the
tools you need from a hardware store.
2. Torque Wrench:
If you plan to adjust and maintain this chair yourself, Quickie
recommends that you use a torque wrench.
Q-NOTE– The wrench must measure inch-pounds (N.m). You can buy
a torque wrench and proper sockets from a hardware store.
CHECK-OUT
Be sure this chair performs to your chosen operational settings. If it
does not, turn the chair off immediately and have the dealer repro-
gram.
Q-NOTE– Repeat this procedure until the chair performs to your spec-
ifications
WARN NG
When properly set-up, this chair will operate smoothly.
Check to see that all components work properly. f you
detect a problem, be sure to correct it before use.
NOTES
1. Work Surface For Set-Up:
Use a flat surface, such as a table, to assemble, adjust and check your
chair. This makes the steps easier and helps ensure a correct set-up.
2. Fasteners:
• Many of the screws and bolts on this chair are special high-
strength fasteners and may have special coatings.
• Many nuts are of the Nylock type. They have a plastic insert
to help prevent loosening.
• Only use screws, bolts and nuts provided by Sunrise.
WARN NG
1. Use of improper fasteners may cause the chair to fail.
2. Over- or under-tightened fasteners may fail or cause
damage to chair parts.
3. If bolts or screws become loose, tighten them as soon
as you can. oose bolts or screws can cause damage to
other chair parts causing them to fail.
3. Washers & Spacers:
• Note the position of washers and spacers before disassembly.
• To avoid damage to the frame, replace all washers and spac-
ers when you reassemble parts.
4. Torque Settings:
• A torque setting is the optimal tightening for a particular fas-
tener. Use a torque wrench that measures inch-pounds to
secure screws, nuts and bolts on this chair.

112670 Rev. A
15
RHYTHM VIII.
A. BATTERY REMOVAL
To remove the batteries for transporting or servicing:
Remove Batteries
a. Remove both safety pins (A) from latch assembly.
b. Lift levers on both sides and tilt seat back to allow access to the battery compartment.
c. Remove the shroud cover by lifting up on the handle (B) as pictured.
d. Disconnect both battery harnesses as pictured.
e. Lift the battery from the compartment via the battery carrying straps.
WARN NG
Batteries may weigh up to 55 lbs. (25 kg). Care must be taken to avoid injury
when lifting.
B. FOLD NG BACKREST
Quickie Rhythm wheelchairs are shipped with backrest in folded position. (optional)
1. Upright Positioning
a. Lift backrest to upright position so that latch handles (C) lock into place.
b. Backrest is ready for use.
2. Folding Backrest
a. Lift and turn backrest latch handles (C) inward
or outward.
b. Fold backrest forward.
WARN NG
Backrest latches must be locked into place before operating wheelchair.
A
B
C

112670 Rev. A 16
RHYTHM VIII.
C. SW NG-AWAY FOOTRESTS
1. nstallation
a. Place swing-away pivot pin (B) into the locating hole (C) on top of the hanger mount
with the footrest facing outward from frame.
b. Rotate the footrest inward until latch plate locks (D) into place on locking bolt.
2. Removal
a. To remove footrest, press quick-release lever ( ).
b. Rotate footrest outward and lift.
3. Height Adjustment
a. Remove both bolts (F) in the hanger frame tube.
b. Reposition footrest height.
c. Re-tighten all bolts (F).
D ELEVAT NG LEGREST (OPT ONAL)
1. nstallation
To install or remove levating Legrest ( LR) see instructions for Swing-away Footrest installa-
tion.
2. Adjustment
a. To raise legrest, lift to desired position. Legrest will automatically lock in place.
b. To lower legrest, while seated in chair, first lift slightly then press release lever (G)
down and lower legrest to desired position.
E. CENTER MOUNT HANGER ADJUSTMENT
(ASAP Seating only)
1. Removal
a. Remove the seat pan by removing the four attachment bolts (H).
b. Remove the four bolts (I) and slide the footrest out.
2. Height Adjustment
a. Remove the six securing bolts (J).
b. Move footplate to desired height.
c. Re-install bolts (J) through desired holes.
3. Calf Pad Adjustment
a. Remove the two securing bolts (K).
b. Move calf pads to desired height.
c. Re-install bolts (K) through desired holes.
G
F
B
C
D
E
H
J
K

VIII.
F. JOYST CK
Controls:
• L D Joystick and color display joystick
Omni nput/Display
The Omni is a universal specialty controls interface that accepts signals from many different
types of SIDs and translates them into commands compatible with the PG Drives Technology
RN T control system.
Mating Connectors
To connect the communication cables:
Holding the connector housing, firmly push the connector into its mate until you can
no longer see the yellow plastic. The connectors are secured using a friction system.
To disconnect the communication cables:
Holding the connector housing firmly, pull the connectors apart.
NOTE– Do not hold or pull on the cable. Always rip the connector when connectin and disconnectin .
When the control system is first switched on after a connection, or system component
change, the timer will be displayed while the system checks itself. Then the re-start icon will
be displayed. Switch the control system off and on again to operate,
G. JOYST CK RETRACTABLE MOUNT (Optional) (Fig. 10)
The joystick or nhanced Display is mounted with a mechanism which allows the control to
be locked in a forward or retracted position using magnets.
Adjustment
a. To retract the joystick, push outward on the inside of joystick.
b. Push the joystick away from front of armrest until it locks into retracted position.
c. To return to forward position, push the joystick forward until it locks into place.
H.DUAL-POST HE GHT-ADJUSTABLE ARMRESTS (OPT ON),
F XED HE GHT STANDARD
The dual-post flip-back armrest can be used as either a flip-back armrest or a removable
armrest.
1. nstalling Armrest
a. Insert front and rear posts into armrest receivers.
b. ngage levers (A and B) to secure armrest.
2. Set-up for Flip-back Operation
a. Disengage lever (A) so front post is able to come free.
b. Armrest now has the ability to be flipped back without removal.
3. Set-up for Removal
a. Disengage levers (A and B) so front and rear posts are able to come free.
b. Armrest can now be easily removed for transferring.
4. Height-Adjustment (option)
a. Release the upper securing lever (C).
b. Set at desired height
c. Return securing lever to locked position.
d. Move armrest up or down to allow armrest to snap into place
A
B
C
112670 Rev. A
17
RHYTHM
10
power
module
LCD screen
Profile +/-
Navigation
Mode
On/Off
L D Joystick Color Joystick
joystick
communication
cable
Omni Display

112670 Rev. A 18
RHYTHM VIII.
. S NGLE POST HE GHT-ADJUSTABLE ARMRESTS
(OPT ONAL)
1. nstallation
a. Slide the outer armpost into the receiver mounted to the wheel chair frame.
b. The armrest will automatically lock into place.
2. Height Adjustment
a. Rotate release lever to stop.
b. Slide armrest pad up or down to desired height.
c. Return lever to locked position.
d. Push arm pad until upper armpost locks firmly into place.
3. Removing Armrest
a. Rotate release lever and remove the armrest.
4. Replacing Armrest
a. Slide armrest back into receiver.
b. Return release lever to locked
position against armpost.
5. Adjusting Armrest Receiver Fit
To tighten or loosen the fit of the outer armpost in the receiver:
a. Loosen the four bolts on the sides of the receiver.
b. With the armrest in the receiver, squeeze the receiver to achieve the desired fit.
c. Tighten the four bolts.
6. Adjusting nner Armpost Fit
a. Two set screws are installed in the outer armpost.
b. Turn the set screws in or out until the desired fit is achieved.
J. SEAT DEPTH 14" - 16", 20" - 22" only
The seat depth can be adjusted in one inch increments on standard rehab seating.
1. Seat Frame Depth Adjustment
a. To adjust, remove the two bolts (A & B) from each side of the backrest pivot plate.
b. Reposition the backrest to the desired position.
c. Replace and retighten bolts on each side of the backrest pivot plate.
2. Back Angle Adjustment on Seat Frame
a. Remove the front securing bolt (A) on the side of the backrest hinge plate.
b. Loosen the lower rear bolt (B)
c. Set at desired angle. There are five holes (in 4º increments) to choose from.
d. Reinstall the front bolt and tighten both bolts securely.
K. TRANS T OPT ON
WARN NG
1. Use only Wheelchair Tie-down and Occupant Restraint Systems (WTORS) which meet
the requirements of SA J2249 Recommended Practice– Wheelchair Tie-down and
Occupant Restraint Systems For Use in Motor Vehicles. Do not use WTORS designed
to rely on the wheelchair structure to transfer occupant restraint loads to the vehicle.
2. The wheelchair has been dynamically tested in a forward-facing mode for a 30 mph
frontal impact test. The wheelchair must be forward-facing during transport.
3. In order to reduce the potential of unjury to vehicle occupants, wheelchair-mounted
accessories, such as trays and respiratory equipment, should be removed and secured
separately.
4. Postural supports and positioning devices should not be relied on for occupant
restraint.
5. Do not alter or substitute wheelchair frame parts, components or seating.
6. Sudden stops or impacts can structurally damage your chair. Chairs involved in such
incidents should be replaced.
9
2
6
7
1
4
3
5
8
Height-Adjustable Armrest Key
1. Inner Arm Post
2. Receiver
3. Release Lever, Locked Position
4. Armrest Pad
5. Transfer Bar
6. Side Panel
7. Tension Adjustment Set Screw
8. Outer Arm Post
9. Receiver Adjustment Bolts
AB

VIII.
SEATING S STEM SET-UP
A. ASAP SEAT NG ADJUSTMENT
Please refer to the ASAP Seating Adjustment Guide for details on how to adjust the seat
depth, seat width, armrest height and backrest angle.
Pretilt
• For 0° pretilt use holes 3 & 6 (Fig. 4) on bracket interface with hole B (Fig. 1)
on curved bracket.
• For 5° pretilt use holes 3 & 6 (Fig. 4) on interface with holes B & C (Fig. 2)
on curved bracket.
• For 9° pretilt use holes 3 & 6 (Fig. 4) on interface with holes A & C (Fig. 3)
on curved bracket.
B. SEAT PAN AND BACK S ZE ADJUSTMENTS
Your Perfect Fit seating system can be adjusted to a wide range of widths and depths to
accommodate specific user needs. Seating dimensions should only be altered by a trained
professional and may require new seat cushions. Please refer to the Perfect Fit Growth
Guide for more detailed instructions on how to customize the size of your seat.
C. PRE-T LT (PACKER MODULE ONLY)
The Packer Module can be mounted with the use of an additional mounting bracket to pro-
vide four different pre-tilt settings (0°, 3°, 6°, 9°). Figure 4 demonstrates these angles and
how they can be achieved using the mounting bracket and two sets of screws. To achieve 0°,
the Packer Module should be bolted directly to the seat frame interface.
SEATING S STEM ADJUSTMENT
A. MANUAL RECL NE OPERAT ON
The Perfect Fit seating system has two manual recline options. The first is using a 16mm
socket wrench and the second can be done by turning a knob on the side of the chair (Figure
5). To recline the chair, rotate this knob clockwise and turn the knob counter-clockwise to
return the back to a more upright position.
B. POWER RECL NE T LT/L FT OPERAT ON
The power recline, tilt, and lift features on your chair can all be operated using the joystick on
your chair. Follow the instructions below to operate:
1. Make sure your controller is on.
2. From the Drive Mode, press the Mode button to enter Power Seating Mode.
3. Move the joystick left or right selecting the power option (recline, tilt, legrests) you
wish to control.
4. Move the joystick forward or backward to adjust the selected power option to the
desired position.
5. Press the Mode button to return to normal operation or continue moving the joystick
left or right to adjust the next power option. Multiple Mode button presses will be
necessary if other modules, such as Bluetooth or Output, are active.
4
B
C
D
E
36
5
112670 Rev. A
19
RHYTHM
For 0° pretilt use Hole B
For 3° pretilt use Hole C
For 6° pretilt use Hole D
For 9° pretilt use Hole
1
A
B
C
2
A
B
C
3
A
B
C

112670 Rev. A 20
RHYTHM
IX . OP ER ATING GUID E
A. PERFORMANCE CONTROL SETT NGS
Q-NOTE– Seek advice re ardin checkin and adjustin settin s.
1. It is vital to match control settings to your level of function and ability.
2. Consult your health care professional and your supplier to select the best control set-
tings for you.
3. Check and adjust the settings every six to twelve months.
WARN NG
Adjust the control settings immediately if you notice any change in your ability
to:
• Control the joystick.
• Avoid running into objects.
B. ON BOARD PROGRAMMER OR DTT (D AGNOST C TEST
TOOL) OR RNET PC PROGRAMMER (Optional)
WARN NG
Program settings beyond the ability of the user can result in serious injury.
Consult your health care advisor before you alter settings.
The On-board Programmer or RN T PC Programmer lets you adjust the control settings of
the Pulse. Listed below are a few of the many settings that can be adjust via the On-board
Programmer or RN T PC Programmer. (See RN T OBP Owners Manual for full program-
mable parameters.)
• acceleration rate
• deceleration rate
• turn acceleration
• turn deceleration
• forward speed (max & min)
• reverse speed (max & min)
• turn speed (max & min)
• steer correct
Programming the Chair:
a. Access via OBP (On-board Programmer), DTT (Diagnostic Test Tool), or the PC
Programmer. ach of these require inline connection to the communication cable.
b. Program as needed.
c. Remove Dongle or recycle power.
NOTE– Review the RNET OBP Owner’s Manual for more details on how to pro ram your chair.
C. THERMAL ROLL-BACK
Your chair has a thermal roll back circuit. This protects the controller from damage due to
overheating. In extreme conditions (such as repetitive hill climbing) the circuit will decrease
the power to your motors. This allows the chair to operate at a reduced speed. When the
controller cools, the chair will return to normal speed.
D.FUSES
Your Quickie Rhythm has two inline fuses.
• In the unlikely event of a short circuit or other fault, all power to your chair will be
shut off.
• Qualified service personnel are required to repair the fault and replace the battery har-
nesses.