Sunset Trading DLU-ADW-TLB-4276 User manual

Center Leaf
Table Top
5
4
Corner
Block
Apron
3
12.8
2
1
SKU: DLU-ADW-TLB-4276
Push the side Center Top at both end close to the
Table Leaf until it leaves no empty spaces.
Turn the assembled Table over carefully,pull the Table Top
to both two sides then lift up the Center Leaf from the
compartment and turn the Center Leaf to open to lie on apron.
Repeat the same step for the other three Legs .
Fix the turned Leg to the corner of the apron with
the Flat Washer , Spring Washer And Hex Nut
using the Spanner to tighten it.
Turn the under side of the Table Top over
and place it on a clean and smooth surface
such as rug or carpet to avoid the Table Top from
being scratched .
ASSEMBLY INSTRUCTIONS
Table Leg
Center Leaf
Table Top 1
1
4
List of Parts For 1 Set
Open the Table Hock under the
table before Center Leaf
is assembled and lock it.
d
Table Leg
Table Top
List of Hardware For 1 Set
IMPORTANT NOTES:
d
c
b
a
1
8
8
8
12.8
Flat Washer
Spring Washer
Spanner
Hexagon Nut
01
02
03
03
03
03
03
03
01
02
01
02
01
02
02
01
03
01
02
01
02
01
01
01
01
01
01
01
02
02
02
03
01
abc
d
a
b
c
701 E Industrial Pk Dr
Manchester, NH 03109
sunsettrading.com
Thank you for purchasing this quality
product! It has been engineered for easy
assembly yet constructed for durability.
Please take the time to read and follow
the instructions while assembling.
Please Contact us if you are
Missing Parts or have any Questions
877-364-8464
[email protected]
• Keep all hardware and small parts
out of reach of children.
• Remove all staples and packing
straps before you start to assemble.
• Do not discard main cartons and
wrapping material until assembly is
complete.
• Check to be sure you have all parts
and hardware.
• Place all wooden parts on a clean
soft surface to avoid parts from
being scratched.
• Do not tighten all screws / bolts until
completely assembled.
• Check tightness 3x's/year, with use
screws can become loose.
• Do not attempt to repair or modify
parts that are broken or defective.
Please contact us immediately.
• Enjoy your new furniture!
MADE IN MALAYSIA

MADE IN MALAYSIA
IMPORTANT NOTES:
ASSEMBLY INSTRUCTIONS
SKU: DLU-ADW-C12WD-RTA
02
f
b
ed
Step 1
Step 2
List of Parts For 1 Set
10
Flat Washer
1/4" x 18mm
01
List of Hardware For 1 Set
b
a
Chair Back
1
Front Leg 2
10
Spring Washer
1/4"
e
f1
Code Figure Part Qty.
Code Figure Hardware Qty.
Spanner
10mm
c
d
4
Hex. Bolt
M6 x 80mm
4
Hex. Bolt
M6 x 60mm
2
Hex. Bolt
M6 x 40mm
02
03
Seat Frame
1
c
a
e
e
d
d
f
f
01
01
02
02
03
03
Thank you for purchasing this quality product!
It has been engineered for easy assembly yet
constructed for durability.
Please take the time to read and follow
the instructions while assembling.
701 E Industrial Pk Dr
Manchester, NH 03109
sunsettrading.com
Please Contact us if you are
Missing Parts or have any Questions
877-364-8464
[email protected]
• Keep all hardware and small
parts out of reach of children.
• Remove all staples and
packing straps before you start
to assemble.
• Do not discard main cartons
and wrapping material until
assembly is complete.
• Check to be sure you have all
parts and hardware.
• Place all wooden parts on a
clean soft surface to avoid
parts from being scratched
• Do not tighten all screws / bolts
until completely assembled.
• Check tightness 3x's/year, with
use screws can become loose.
• Do not attempt to repair or
modify parts that are broken or
defective. Please contact us
immediately.
• Enjoy your new furniture!