Sunset Trading DLU-TLB-3660 User manual

Hexagon Nut
5
16" x 7mm
Spanner
12.8mm
Flat Washer
5
16" x 22mm
12.8
List of Hardware For 1 Set
List of Parts For 1 Set
Table Top
Table Leg
With Nail Leg
Spring Washer
5
16"
a
b
c
d
01
02
1
4
1
8
8
8
01
Apron
12.8
02
abc
d
01
Remove the plastic
cover from the
Pedestal and Footings.
02
Open the Table Hock under the
table before Center Leaf
is assembled and lock it.
SKU: DLU-TLB-3660
ASSEMBLY INSTRUCTIONS
1Turn the under side of the Table Top over
and place it on a clean and smooth surface
such as rug or carpet to avoid the Table Top from
being scratched .
2Fix the turned Leg to the corner of the apron with
the Flat Washer ,Spring Washer And Hex Nut
using the Spanner to tighten it.
3Repeat the same step for the other three Legs .
4Turn the assembled Table over carefully,pull the Table Top
to both two sides then lift up the Center Leaf from the
compartment and turn the Center Leaf to open to lie on apron.
5Push the side Center Top at both end close to the
Table Leaf until it leaves no empty spaces.
01
IMPORTANT NOTES:
Thank you for purchasing this quality
product! It has been engineered for easy
assembly yet constructed for durability.
Please take the time to read and follow
the instructions while assembling.
701 E Industrial Pk Dr
Manchester, NH 03109
sunsettrading.com
Please Contact us if you are
Missing Parts or have any Questions
877-364-8464
[email protected]
• Keep all hardware and small parts
out of reach of children.
• Remove all staples and packing
straps before you start to assemble.
• Do not discard main cartons and
wrapping material until assembly is
complete.
• Check to be sure you have all parts
and hardware.
• Place all wooden parts on a clean
soft surface to avoid parts from
being scratched.
• Do not tighten all screws / bolts until
completely assembled.
• Check tightness 3x's/year, with use
screws can become loose.
• Do not attempt to repair or modify
parts that are broken or defective.
Please contact us immediately.
• Enjoy your new furniture!
MADE IN MALAYSIA

7Flat Washer
Seat Board
ASSEMBLY INSTRUCTIONS
01
List of Parts For 1 Set
List of Hardware For 1 Set
b
a
SKU: DLU - C07 WS
1
Back Frame
1
Right Front Leg
(RF)
1
7
Spring Washer
e
f1
Code Figure Part Qty.
Code Figure Hardware Qty.
Spanner
c
d
IMPORTANT NOTES:
Left Strecher
(LS)
1
Center Strecher
(CS)
1
a
e
d
f
c
e
d
Step 1
d
e
b
f
Step 2
Step 3
2
Hex. Bolt
80mm
2
Hex. Bolt
60mm
3
Hex. Bolt
40mm
g6
PHRS Screw
# 8 x 1 1/4''
Left Front Leg
(LF)
1
Right Strecher
(RS)
1
RF
RS
LS
CS
03
04
05
06
07
08
h4
PHRS Screw
# 8 x 1''
Seat Frame
02 1
03
03
02
02
02
H
01
02
LF
RF
gg
gg
g
g
Step 4
LF
RF
01
03
Thank you for purchasing this quality product!
It has been engineered for easy assembly yet
constructed for durability.
Please take the time to read and follow
the instructions while assembling.
701 E Industrial Pk Dr
Manchester, NH 03109
sunsettrading.com
Please Contact us if you are
Missing Parts or have any Questions
877-364-8464
[email protected]
• Keep all hardware and small
parts out of reach of children.
• Remove all staples and
packing straps before you start
to assemble.
• Do not discard main cartons
and wrapping material until
assembly is complete.
• Check to be sure you have all
parts and hardware.
• Place all wooden parts on a
clean soft surface to avoid
parts from being scratched
• Do not tighten all screws / bolts
until completely assembled.
• Check tightness 3x's/year, with
use screws can become loose.
• Do not attempt to repair or
modify parts that are broken or
defective. Please contact us
immediately.
• Enjoy your new furniture!
MADE IN MALAYSIA