Sunset Trading DLU-TPD-4242-B User manual

Thank you for purchasing this quality
product! It has been engineered for easy
assembly yet constructed for durability.
Please take the time to read and follow
the instructions while assembling.
701 E Industrial Pk Dr
Manchester, NH 03109
sunsettrading.com
Please Contact us if you are
Missing Parts or have any Questions
877-364-8464
[email protected]
• Keep all hardware and small parts
out of reach of children.
• Remove all staples and packing
straps before you start to assemble.
• Do not discard main cartons and
wrapping material until assembly is
complete.
• Check to be sure you have all parts
and hardware.
• Place all wooden parts on a clean
soft surface to avoid parts from
being scratched.
• Do not tighten all screws / bolts until
completely assembled.
• Check tightness 3x's/year, with use
screws can become loose.
• Do not attempt to repair or modify
parts that are broken or defective.
Please contact us immediately.
• Enjoy your new furniture!
Remove the plastic
cover from the
Pedestal and Footings.
03
12.8
03 03
03
02
02
a
b
c
d
SKU: DLU-TPD-4242-CB
ASSEMBLY INSTRUCTIONS
IMPORTANT NOTES:
1Turn the under side of the Table Top over
and place it on a clean and smooth surface
such as rug or carpet to avoid the Table Top from
being scratched .
2Fix the Footing to the Pedestal with
the Flat Washer,Spring Washer And Hex Nut
using the Spanner to tighten it.
3Repeat the same step for the other three Footing .
MADE IN MALAYSIA
4Fix the Pedestal with Flat Washer,Spring Washer & Hex Nut
using the Spanner to tighten it.
Hexagon Nut
5
16" x 7mm
Spanner
12.8mm
Flat Washer
5
16" x 22mm
12.8
List of Hardware For 1 Set
List of Parts For 1 Set
Table Top
Pedestal
Table Leg
With Leveler
Spring Washer
5
16"
a
b
c
d
01
02
03
1
1
4
1
12
12
12
02
03
Mouting Plate
a
b
c
d
01
03
12.8
01
01
01
SKU: DLU-TPD-4242-B
Remove the strip before start Assembly .

Swivel Barstool Assembly Models: B24, B30, B124-24
Thank you for your purchase and we appreciate your business. We hope you enjoy your new stools! The Sunset Trading Team
[e-mail] | Toll Free: 877-364-8464
•Check to be sure that you have all parts and hardware
•Place all wooden pieces on a clean and smooth surface
like a carpet to avoid parts being scratched
•Do not tighten all screws/ bolts until completely
assembled
•*Swivel plate top & bottom are pre-turned 90-degrees
prior to installation. To troubleshoot swivel turning
issues, please place swivel plate on your floor, use
packaging carton to protect the surface, step on swivel
TOP to twist using your body weight
•If missing parts or have questions, please email
[e-mail] or call Sunset Trading
877-364-8464, M-F 8am-4pm EST.
BEFORE YOU BEGIN
Step 1. Place swivel on base with ‘TOP FRONT’ markings on swivel
facing upward. Attach swivel to base using four (4) #10 Philips screws
and four (4) flat washers. Tighten with a #10 Philips screwdriver (Not
Provided). (Fig 1)
Step 2. Place seat upside down on table or bench (lay a towel down to
protect from scratches) or on the edge of mattress. Flip base upside down
and place on top of Seat Unit bottom. Line up the four (4) slots in the
swivel top with the four (4) nut inserts that are mounted in the seat. (Fig 2)
*IMPORTANT: Make note of marking on top of swivel that reads
‘TOP FRONT’. This side of the swivel must be mounted toward the
front of the barstool seat in order to provide proper angle for sitting.
Step 3. Put one (1) Lock Washer and one (1) Flat Washer on each Seat
Machine Bolt. Attach the swivel to the seat bottom through the access
hole in the bottom of the base Unit with all four (4) bolts. (Fig 3)
Step 4. Screw all 4 bolts in half way with Allen wrench provided. Turning
base unit as needed to access the nuts that are inserted on the barstool
seat. Tighten all bolts fully when done. Assembly is complete!
Parts
QTY
Top Seat Unit
(Pre-Assembled)
1
Base
(Pre-Assembled)
1
Swivel Plate
1
Seat Machine Bolts
4
Lock Washers
4
Flat Washers
8
#10 Philips Screws
4
4mm Allen Wrench
1
Bottom of base
Bottom of seat
(Fig 1)
(Fig 2)
(Fig 3)