SUPER NOVA VK-2995 User manual

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Top View
20’
10’
VK-2995 Inline Lightbox
REV 01/2023

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View

© 2023
Order #XXXXX General Information
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED

© 2023
Order #XXXXX CEI110 Frame Assembly
Straight Connection
All knobs must be tightened securely to ensure a proper connection.
All knobs must be tightened securely to ensure a proper connection.
Adjust connectors if necessary to
prevent gaps in connection.
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Straight Connector
Straight Connector
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
COMPLETED ASSEMBLY
3) Tighten all knobs to secure connection.
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
When assembling frame, first attach all straight
connectors, then attach corner connectors.
1) Place extrusions end-to-end.
2) Loosen all knobs, then slide straight
connectors across the seam of extrusions.
Disassembly
1) Loosen all knobs.
2) Slide connectors off of one extrusion.
3) Tighten knobs to prevent loss during
packing & shipping.
CEI110 Profile
Slide both connectors across seam of extrusions.
Tighten all knobs.
Corner Connection
3) Tighten all knobs to secure connection.
Disassembly
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
Keep straight connectors in groove of
extrusion. Do not remove connectors
during disassembly.

© 2023
Order #XXXXX SEG Installation
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from

© 2023
Crate 1 of 1
Order #XXXXX Crate Packing
Locked layer contains
placeholder marks.
CRATE PACKING

© 2023
Step 1 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
Item
1,1A
2,2A
3,3A
4
5,5A
6,6A
7
Qty.
1,1
1,1
1,1
1
1,1
1,1
2
Description
57” CEI110 Horizontal Extrusion
57” CEI110 Horizontal Extrusion
95” CEI110 Vertical Extrusion
91.353” Z45 Vertical Extrusion
42” CEI110 Horizontal Extrusion
95” CEI110 Vertical Extrusion
Base Plate
Steps:
Steps 1 to 3 can be assembled flat on floor. See CEI110 Frame Assembly sheet.
1) Attach horizontals [1 to 2] and [1A to 2A].
2) Attach horizontal assemblies between verticals [3] and [3A].
3) Attach horizontals [5] and [5A] between verticals [6] and [6A].
4) Attach vertical [4] between horizontals [1] and [1A]. See Z45 Attachment detail.
5) Attach base plates to [1/3] and [5/6A]. See Base Plate Attachment detail.
6) Connect lights and transformers then connect to power. See Light details.
1
7
25
5A
1A
3
6
3A
4
6A
2A
*
**
*
CEI-110
Z45
Z45 Attachment
Attach Z45 vertical to back
groove of CEI-110 horizontal.
*
F
r
o
n
t
of
F
r
a
m
e
7
*
Base
Plate
Bolt
Bolt
Bolt
Vertical
Extrusion
Horizontal
Extrusion
Base Plate Attachment
Place key hole over bolt on vertical
extrusion then slide down. Secure
with bolt, washer, and wing nut.
Washer
Wing Nut
Key Hole
Power Break
Power Break
Power Break Power Break
++
--
Lights Male
Light to Light Attachment
Maximum of 7 lights per chain,
11 lights per Transformer
Light to Transformer Attachment
+
-
Power
Female
Transformer
144W / 6 Amp / 24V
Left and Right Lightbox Assembly

© 2023
Step 2 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
Item
8,8A
9,9A
10
11
12,12A
13
14
15,15A
Qty.
1,1
1,1
1
2
1,1
1
2
1,1
Description
70” CEI110 Horizontal Extrusion
95” CEI110 Vertical Extrusion
91.353” Z45 Vertical Extrusion
26” Z45 Horizontal Extrusion
95” S44 Vertical Extrusion
25.547 Door Threshold
26” Z45 Horizontal Extrusion
95” S44 Vertical Extrusion
Steps:
1) Attach horizontals [8] and [8A] between verticals [9] and [9A].
See CEI110 Frame Assembly sheet.
2) Attach vertical [10] between horizontals [8] and [8A]. See
Z45 Attachment detail.
3) Connect lights and transformers then connect to power.
See Light details.
8
8A
99A
Keep closet side and closet door
assembled during packing.
10
*
*
Door
Threshold
Tighten
setscrew
to secure.
Slide connector
into groove
of extrusion.
Door Threshold
Attachment
*
11
ASSEMBLED
CLOSET SIDE
(Exterior View)
CLOSET FRONT
(Exterior View)
ASSEMBLED
CLOSET DOOR
(Exterior View)
13
11
12 15 DoorInfill 12A 15A
14
14
CEI-110
Z45
Z45 Attachment
Attach Z45 vertical to back
groove of CEI-110 horizontal.
*
F
r
o
n
t
of
F
r
a
m
e
* *
Power Break
Power Break
++
--
Lights Male
Light to Light Attachment
Maximum of 7 lights per chain,
11 lights per Transformer
Light to Transformer Attachment
+
-
Power
Female
Transformer
144W / 6 Amp / 24V
Closet Assembly

© 2023
Step 3 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
Item
16
Qty.
2
Description
70” Z45 Horizontal Extrusion
Steps:
1) Attach closet side to vertical [9] and closet door to vertical [9A],
using bolts, making sure the Velcro is facing to back.
2) Attach horizontals [16] between [12] and [15A], making sure the
Velcro is facing to back.
3) Attach left lightbox to vertical [12] and right lightbox to vertical [15A],
using bolts.
See SEG Installation sheet for steps [4] thru [5].
4) Install SEG graphic to front of closet and each lightbox.
5) Install fabric blocker to back of each lighbox.
6) Connect fabric blocker to Velcro on back of assembled closet.
16
Assembled
Closet Side Assembled
Closet Door
16
12 12
99A
15A 15A
CLOSET ASSEMBLY ASSEMBLED CLOSET
LEFT LIGHTBOX
RIGHT LIGHTBOX
Closet Attachments

© 2023
Step 4 of 6
Order #XXXXX
Locked layer contains
placeholder marks.
Completed Assembly
Steps:
1) Assemble lower horizontals [7,8,9,10] between
verticals [1,2,3,4,5].
2) Slide Infills between verticals as shown.
3) Attach upper horizontals [7A,8A,9A,10A], securing infills.
4) Connect lower horizontals [16,17,18,19] between verticals
[4,12,13,14,15].
5) Slide Infills between verticals.
6) Secure Infills with upper horizontals [16A,17A,18A,19A].
7) Connect doors to vertical [3] and [13]. See Door Connection detail.
Item
1
2
3
4
5
7,7A
8,8A
9,9A
10,10A
Qty.
1
1
1
1
1
1,1
1,1
1,1
1,1
Description
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
8.341” Z45 Horizontal Extrusion
8.341” Z45 Horizontal Extrusion
21.825” Z45 Horizontal Extrusion
8.341” Z45 Horizontal Extrusion
12
13
14
15
16,16A
17,17A
18,18A
19,19A
1
1
1
1
1,1
1,1
1,1
1,1
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
39.5” S44 Vertical Extrusion
4” Z45 Horizontal Extrusion
16.067” Z45 Horizontal Extrusion
4” Z45 Horizontal Extrusion
8.341” Z45 Horizontal Extrusion
16A
16
12
13
14
15
19A
18A
17A
17
18 19
4
*
*
*
*
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Connection
*
Pin
17A 8A
9A
10A
2
3
4
5
9
8
7
10
Infill
Infill
Infill
Infill
Infill
Door Door
MOD-1702 Counter Assembly