superbrightleds RGB-MDC83 User manual

Begin the installation, by connecting an appropriate power supply
to the controller. With the controller in standby mode (o󰀨) use the
button to select each setting and buttons to adjust the
setting values to match the table below.
Once all setting adjustments have been made, and
with supply power o󰀨, connect strip as shown using
the provided adapter.
Wiring
Important: Read all instructions prior to installation.
Dream-Color Chasing RGB Controller and Remote
• Supports twelve unique IC strip styles and has pixel adjustment from
16 to 2,048 pixels to accommodate di󰀨erent strip lengths.
• Input power should be 5–24 VDC (matching connected strip). Input
power connection is a 5.5 mm / 2.1 mm DC barrel connector.
• Ensure all electrical connections are secure and follow the provided
wiring instructions.
• Strips require data signal to operate properly. Use caution if cutting
strip to custom length as interrupting the data signal will cause the
strip(s) to malfunction. Strips should be powered from a single power
supply connected to the controller, as additional power connections
after the controller will cause the strip(s) to malfunction.
• Jumper wires/interconnects should be no more than 8” between strip
sections to avoid issues with data loss.
Safety and Notes
Specications
FCC Statement
Controller Buttons
Setup and Installation
¹Range may be decreased by interference from electrical signals and
physical barriers
²This setting is for the full 5 m strip, part number NDC2-RGB150. Increase
or decrease the pixel count by 1 for each additional 0.1 meter of strip.
Model RGB-MDC83
Operating Temperature -4°–140° F (-20°–60° C )
Supply Voltage 5–24 VDC
Maximum Output Power 5 A
Maximum Remote Range¹ 175 ft (53.3 m)
Terminal Connection Wire Color for NDC2-RGB150
V- strip negative black
Data strip data green
CLK strip clock blue
V+ strip positive red
Setting Value
IC WS2811
LED Sequence RGB
Pixels² 50
ON/OFF button turns the controller on or o󰀨. The controller must
be o󰀨 (powered on in standby mode) to adjust IC type, pixels,
and LED sequence.
Play/pause button can pause and then resume dynamic modes.
Mode increase/decrease buttons cycle up or down to the
next mode. They also adjust IC type, pixel number, and LED
sequence in the settings. M+ and M- perform the same function
on the remote control.
Speed up/down buttons increase or decrease speed during
dynamic modes. S+ and S- perform the same function on the
remote control.
Value selection buttons cycle through di󰀨erent setting types
(IC type, pixel number, and LED sequence) in standby mode.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation. Any changes
or modications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
WIFI-CON
Important: Read all instructions prior to installation. RGB-MDC83
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V2 01/28/2020
User Manual
V- V+
(Included LC4M-PT
connector)
D C

Modes/Programs
Available Settings
Mode Program
1 Static Red
2 Static Blue
3 Static Green
4 Static Magenta
5Static Yellow
6 Static Cyan
7 Static White
8 Red Chasing / Right
9 Red Chasing / Left
10 Blue Chasing / Right
11 Blue Chasing / Left
12 Green Chasing / Right
13 Green Chasing / Left
14 Red Chasing / Middle to Ends
15 Blue Chasing / Ends to Middle
16 RGB Chasing to Solid / Backward
17 CMY Chasing to Solid / Forward
18 RGB chasing to Solid / Middle to Ends
19 CMY Chasing to Solid / Ends to Middle
20 Seven Color Chasing to Solid / Backward
21 Seven Color Chasing to Solid / Forward
22 Seven Color Chasing to Solid (Backward) and Chasing (Forward)
23 Seven Color Chasing to Solid (Forward) and Chasing (Backward)
24 RGB Color Scan / Forward
25 RGB Scan / Backward
26 CMY Scan / Forward
27 CMY Scan / Backward
28 Seven Color Scan / Forward
29 Seven Color Scan / Backward
30 RGB Scan / Backward Then Flash Once
31 RGB Scan / Forward Then Flash Once
32 Seven Color Scan / Backward Then Flash Once
33 Seven Color Scan / Forward Then Flash Once
34 RGB Flash
35 Seven Color Flash
36 RGB Jump
37 CMY Jump
38 Seven Color Jump
39 GBM Flow / Forward
40 GCM Flow / Backward
41 CMY Flow / Forward
42 CMY Flow / Backward
Mode Program
43 GYCM Flow / Forward
44 GB Alternating
45 GM Alternating
46 Seven Color Flow / Forward
47 Seven Color Flow / Backward
48 Green Comet / Backward
49 Red Comet / Forward
50 Red Comet / Backward
51 Blue Comet / Forward
52 Blue Comet / Backward
53 Green Comet / Forward
54 Magenta Comet / Forward
55 Cyan Comet / Forward
56 Yellow Comet / Backward
57 White Comet / Forward
58 White Comet / Backward
59 Seven Color Comet / Backward
60 Seven Color Comet / Forward
61 RC Gradual Change
62 YR Gradual Change Chasing / Backward
63 N/A
64 MB Gradual Change Chasing / Backward
65 N/A
66 BC Gradual Change Chasing / Backward
67 N/A
68 GY Gradual Change Chasing / Backward
69 N/A
70 CG Gradual Change Chasing/ Backward
71 N/A
72 WR Gradual Change Chasing/ Backward
73 N/A
74 RB Gradual Change
75 RG Gradual Change
76 MR Gradual Change Chasing/ Backward
77 N/A
78 RM Gradual Change
79 RY Gradual Change
80 BC Gradual Change
81 BM Gradual Change
82 GY Gradual Change
83 Scan Modes 1–82
Dream-Color Chasing RGB Controller and Remote WIFI-CON
Important: Read all instructions prior to installation. RGB-MDC83
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V2 01/28/2020
User Manual
This product is recommended for use with SBL strip part number NDC2-RGB150. If this is purchased
to work with any other strip, the following settings are available. IC can be set to LPD6803, WS2801,
P9813, and LPD8806 for data and clock operation, and TM1803, UCS1903, WS2811, TM1812, TM1809,
TLS3011, TLS3008, and TM1829 for data operation. LED sequence can be set to RGB, RBG, GRB,
GBR, BRG, or BGR. Pixel number can be set between 16 and 2,048.