superbrightleds LDRF-RGB6-TC2B User manual

RGB Controller with RF Touch Color Remote
Instruction Sheet
Part Number:
Important: Read all instructions prior to installation.
866-590-3533 [email protected]
To select a static color, press the icon until static color, then
touch the color wheel to select your color.
While in dynamic or static color mode,
Press once to activate white. Brightness is adjustable.
Parts Included
RF Remote
Static White Mode
Static Color Mode
LDRF-RGB6-TC2B
LDRF-RGB6-TC2W
1 - RGB Controller
1 - RF Touch Color Remote
RF remote controller has a signal range
up to 65ft (20m) and requires 3 x AAA
batteries (not included).
Button Functions
Turn all LEDs on and off , retaining
the last setting on power toggle.
COLOR WHEEL Directly select color on wheel from
static color mode or color selection
by touching the color wheel. Rotate
fi nger around to fi ne tune desired
color.
Instant White Mode
Switches between static colors and
static white
BRIGHTNESS +/- Dim LEDs in static white mode and
dynamic mode by pressing ( )
symbol. Brighten LEDs by pressing
( ) symbol.
SPEED +/- Increase ( ) and decrease ( )
speed on dynamic modes.
MODE +/- Cycle through 14 diff erent dynamic
modes.
Pre-test & Confi gure
May be used with RGB strips, bars, modules, or other RGB LED products.
Connect LEDs to power supply and controller (see “Method 1” ).
Turn on LEDs using the included remote controller to ensure proper operation of the
LEDs, power supply, controller, and remote.
Choose suitable dry location for the power supply and controller.
LDRF-RGB6-TC2(Black or White remotes) three channel RGB (Red,
Green, Blue) LED controller with color touchwheel for directly selecting a
wide range of colors.
Off ers 14 dynamic modes and static white with adjustable brightness,
static single color modes, and speed and mode retention (controller
resumes modes with the settings previously selected on power toggle).
General Description
Instructions
Dimming in dynamic mode must be done in the static white mode
fi rst.
Press to activate the white mode.
Press to increase brightness and to decrease
brightness.
Then press to switch back to dynamic mode. Only the modes
listed as adjustable on page 2 for brightness will respond to the
dimming function.
Dynamic Mode Dimming
DO NOT connect controller or LEDs directly to 120V AC
power. This controller requires a 12V or 24V DC power
supply.
DO NOT exceed max load of 18 Amps, overloading the
controller may cause overheating, shorting, and possibly
failure of controller.
Be sure the power supply is not plugged into an outlet before
connecting or disconnecting any of the systems components.
DO NOT expose the controller or remote to direct or indirect
moisture.
Always observe proper polarity when connecting power and
load.
Safety

866-590-3533 [email protected]
1 Three color jump Adjustable Adjustable
2 Seven color jump Not Adjustable Adjustable
3 Three color fade Not Adjustable Adjustable
4 Seven color fade Adjustable Adjustable
5Red strobe-fl ash Adjustable Adjustable
6Green strobe-fl ash Adjustable Adjustable
7Blue strobe-fl ash Adjustable Adjustable
8Yellow strobe-fl ash Adjustable Adjustable
Mode Function Brightness Speed Controls Mode Function Brightness Speed Controls
Note: “ ” and “ ” changes dynamic modes
Note: Adjustable brightness can only be changed in white mode
FCC Statement
Wiring: Method 1
Modes List
Specifi cations
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation. Any changes or modifi cations in construction
of this device which are not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
Type 3 Channel
Input Voltage 12~24 VDC
Output 6 Amps / Ch
Total Output 18 Amps
Max Wattage 216W (12V) / 432W (24V)
Operating Temp -4° ~ 140° F (-20° ~ 60°C)
Controller Size L3.2in x W2.5in x D.9in (81 x 64 x 24mm)
Controller Weight 55g (1.94oz)
Frequency 433MHz
FCC ID 2AFRVFC433RMT5
Batteries 3 x AAA (Not Provided)
9Cyan strobe-fl ash Adjustable Adjustable
10 Purple strobe-fl ash Adjustable Adjustable
11 White strobe-fl ash Adjustable Adjustable
12 Red-blue fade Not Adjustable Adjustable
13 Green-blue fade Not Adjustable Adjustable
14 Red-green fade Not Adjustable Adjustable
RGB LED Flexible Light Strip
RGB LED Flexible Light Strip
To Power Supply
(Match voltage to LED voltage)
+
-
+
R
B
G
+
R
B
G
+
R
B
G
+
R
B
G
+
R
B
G
+
R
B
G
+
R
B
G
+
R
B
G
Solder or use
solderless connectors
RGB Controller with RF Touch Color Remote
Instruction Sheet
Part Number:
Important: Read all instructions prior to installation. LDRF-RGB6-TC2B
LDRF-RGB6-TC2W