Superfeed SC41 User manual

OPERATIONAL MANUAL
FOR
CONTROLLER SC41
www.fujicon.com.sg 1

Contents
Page
1. Introduction 1
2. Precaution 2
3.Specifications 3
4.Features 4
5. Input/Output 5
6. Control Panel and function 6
7.Preparation 7
8.Operation 8
www.fujicon.com.sg 2

1. Introduction
Thank you for your purchase purchasing Superfeed products. For correct operation
of the controller, read the operational manual carefully before use, and ensure
execution of safe work through correct operation. You are requested to keep the
operation manual carefully after read.
This is direct solution to most of the vibratory driver needs for feeder system. It is a
4 in 1 controller. It has 4 functions which are simple and meeting the basic needs for
vibratory driver.
The functions are:-
1. AC115V/AC230V Input Voltage
2. 3 kHz or 6 kHz Frequency Selection
3. Adjustable Gain
4. Adjustable Output Voltage
www.fujicon.com.sg 3

2. Precautions
Note to Users
Part feeder is a heavy weight machine, so that movement, setting up and installation,
must be done by equipment in order to avoid injury.
Control system consists of different type of controllers and devices. Adjustment and
maintenance must be preceded in accordance to the manual of each controller.
Feeder manufacturer is not responsible for any machine trouble or human injury
caused by the parts feeder after being modified or additionally processed by a third
party other than the manufacturer after delivery.
Specifications and contents of this manual are subject to change without any
obligation part of the manufacturer.
DANGER: Electric shock!!
Turn OFF primary power source, before any wiring and maintenance.
DANGER: Electric shock!! Connect the grounding wire (green/yellow) before
setting up.
Caution: Never make short circuit between input and output wire.
Caution: Be sure to make wiring for AC115V/AC230V
Single phase (Brown and blue wire for power, green/yellow for
grounding)
www.fujicon.com.sg 4

3. Specifications
2-1. Model SC41 Controller Specification
Power Input Voltage 115Vac or 230Vac
Source Output Voltage 100Vac or 200Vac
Selection Switch 4 Selects Frequency (3kHz or 6kHz)
Status Indicator On – Power on
External VR3 Adjusts GAIN
Setting VR4 Adjusts Output Voltage Control
Housing Dimension (97.5 x 47 x 150)mm (L X B X H)
Case Material Metal
www.fujicon.com.sg 5

4. Features
4-1. Run and Stop Control.
It is control by the input power ON/OFF.
4-2. Variable Input Voltage
AC230V/115V.
4-3. Selectable Frequency (SW4)
Select either 3 kHz or 6 kHz using SW4. 3 kHz is half-wave frequency while
6 kHz is a full-wave frequency.
4-4. Adjustable GAIN (VR3)
Adjust GAIN potentiometer to control output voltage range to obtain
optimum performance.
4-5. Adjustable Output Control Voltage (VR4)
Adjust the output control voltage (0-10) clockwise to increase output voltage.
4-6. Indicator Light
Turns on when power supply is on.
www.fujicon.com.sg 6

5. Input/Output
5-1. Connection
FUSE Holder
(2.5A, 250V)(Insert
fuse here)
5-2. Terminal Connection
Connect terminal with:
•Live input (Brown) and
output
•Neutral input (Blue) and
output
•Ground input
(Green/Yellow)and
output
www.fujicon.com.sg 7

5-2. Picture Illustration
Live wire
(Brown)
Earth wire
(Green/Yellow)
Neutral wire
(Blue)
Fuse (2A,
250V)
To feeder
www.fujicon.com.sg 8

6. Control Panel and Function
6-1. Front Panel
Indicator light
(Indicate
power is on)
ON/OFF Switch
(Switching power
on and off)
GAIN (To control the
out
p
ut volta
g
e ran
g
e
)
Output Voltage Control
(VR4, to control output
voltage correspondently
from 0-10)
Mounting /
dismounting
screw
(x 2)
Mounting hole
www.fujicon.com.sg 9

7. Preparation
7-1. Turn OFF all the power.
7-2. Dismount the front panel by unscrewing the mounting/dismounting screw in
the anti-clockwise direction.
7-3. Connect cable of feeder to controller.
Connect to output cable of the controller to the feeder input cable. Be
particularly aware of live, neutral and earth connection respectively.
7-4. Connect power cable to controller.
Terminal AC power supply according to the selected AC voltage (230Vac or
115Vac) to get ready.
7-5. Connect fuse in the fuse holder.
Insert the fuse properly in the fuse holder in which both side of the fuse must
be in contact with the fuse holder.
7-6. Select SW4 for 3 kHz or 6 kHz frequency selection.
Choose 6 kHz for full-wave frequency or 3 kHz for half-wave frequency.
7-7. Check input and output cables for grounding with multimeter to ensure safety.
7-8. Check and tighten all incoming and outgoing cables termination.
7-9. Mount the front panel by screwing the mounting/dismounting screw in the
clock-wise direction.
www.fujicon.com.sg 10

8. Operation
8-1. ON/OFF Control
Switch ON to power the controller.
8-2. Adjust VR3 (GAIN) to Control Output Voltage Range.
Tune the gain potentiometer in the front panel to control the output voltage
range. Adjust VR4 to mid range example ‘5’ turn VR3 to obtain optimum
performance.
8-3. Adjust VR4 (Output Voltage Control) to Control Output Voltage.
The output voltage control in the front panel is use to control the output
voltage. By turning clockwise the voltage will increase correspondently from 0
to 10.
www.fujicon.com.sg 11