Pacific energy NEO 1.6 INSERT User manual

241013-20 NEO16 5055.700
INSTALLATION
AND OPERATING
INSTRUCTIONS
SAFETY NOTICE
If this stove is not properly installed, a
house re may result. For your safety,
follow the installation instructions. Contact
local building or fire officials about
restrictions and installation inspection
requirements in your area.
TESTED and LISTED to CAN/ULC S627
AND UL 1482
Meets the Environmental Protection
Agency's July 1990 Particulate Emission
Standards
IMPORTANT:
THESE INSTRUCTIONS ARE TO
REMAIN WITH THE HOMEOWNER
MODEL - NEO 1.6
SERIES - A
SERIAL #

2 NEO16 241013-20
PLEASE SAVE THESE INSTRUCTIONS
NOTE: WE STRONGLY RECOMMEND THAT SMOKE DETECTORS BE INSTALLED.
If smoke detectors have been previously installed, you may notice that they are operating more frequently. This may be due
to curing of stove paint or fumes caused by accidentally leaving the re door open. Do not disconnect the detectors. If neces-
sary, relocate them to reduce their sensitivity.
SAFETY NOTICE: If this stove is not properly installed, a house re may result. For your safety, follow the installa-
tion instructions. Contact local building or re officials about restrictions and installation inspection requirements
in you area.
Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in
property damage, bodily injury, or even death.
Contents
Safety.................................................................................................................................... 3
Creosote Formation and Need for Removal .......................................................................................... 3
Chimney Fires........................................................................................................................................ 3
In Case of a Chimney Fire ..................................................................................................................... 3
Avoiding a Chimney Fire........................................................................................................................ 3
Operation.............................................................................................................................. 4
Wood Selection...................................................................................................................................... 4
How to Test Your Wood .......................................................................................................................... 4
Lighting for the First Time ...................................................................................................................... 4
Lighting a Fire........................................................................................................................................ 4
Normal Operation .................................................................................................................................. 4
Restarting After Extended or Overnight Burns....................................................................................... 5
Over Firing............................................................................................................................................. 5
More Wood, More Heat.......................................................................................................................... 5
Proper Draft ........................................................................................................................................... 5
Ash Removal ......................................................................................................................................... 5
Disposal of Ashes .................................................................................................................................. 5
Maintenance......................................................................................................................... 6
Baffle Removal....................................................................................................................................... 6
Maintenance Checks ........................................................................................................... 7
Assembly.............................................................................................................................. 8
Crate Removal....................................................................................................................................... 8
Side Panel Installation ........................................................................................................................... 8
NEO 1.6 Dimensions............................................................................................................ 8
Floor Protector................................................................................................................... 10
Combustion Air.................................................................................................................. 10
Residential Installation ..................................................................................................... 11
Clearances ...........................................................................................................................................11
Chimney and Connector.......................................................................................................................11
Double-Wall Connector.........................................................................................................................11
Single-Wall Connector ..........................................................................................................................11
Procedure .............................................................................................................................................11
Mobile Home Installation .................................................................................................. 12
Clearances .......................................................................................................................................... 12
Procedure:............................................................................................................................................ 13
Optional Blower ................................................................................................................. 14
Blower Operation................................................................................................................................. 14
Optional Outside Air Adaptor ............................................................................................................... 14
Troubleshooting................................................................................................................. 15
Replacement Parts - NEO 1.6.............................................................................................................. 16
Understanding & Operating Your Pacic Energy Stove........................................................................ 17
Label.................................................................................................................................................... 19

241013-20 NEO16 3
Creosote Formation and Need for
Removal
When wood is burned slowly, it produces tar and other or-
ganic vapours, which combine with expelled moisture to form
creosote. The creosote vapours condense in the relatively
cool chimney ue of a slow burning re. As a result, creosote
residue accumulates on the ue lining. When ignited, this
creosote makes an extremely hot re. The chimney connector
and chimney should be inspected periodically (at least once
every two months) during the heating season to determine if
a creosote buildup has occurred.If creosote has accumulated
(3 mm. or more), it should be removed to reduce the risk of
a chimney re.
1. Highest smoke densities occur when a large amount of
wood is added to a bed of hot coals and the air inlet is
closed. The heated wood generates smoke, but without
ample air, the smoke cannot burn. Smoke-free, clean
burning requires small fuel loads, two or three logs at
a time or 1/4 to 1/2 of fuel load and leaving the air inlet
relatively wide open, especially during the rst 10 to 30
minutes after each loading, when most of the smoke
generating reactions are occurring. After 30 minutes or
so, the air inlet can be turned down substantially without
excessive smoke generation. Wood coals create very
little creosote-producing smoke.
2. The cooler the surface over which the wood smoke is pass-
ing, the more creosote will be condensed. Wet or green
wood contributes signicantly to creosote formation as the
excess moisture that is boiled off cools the re, making
it difficult for the tars and gases to ignite, thus creating
dense smoke and poor combustion. This moisture-laden
smoke cools the chimney, compounding the problem by
offering the smoke the ideal place to condense.
In summary, a certain amount of creosote is inevitable
and must be lived with.Regular inspection and cleaning is
the solution. The use of dry, seasoned wood and ample
combustion air will help to minimize the buildup.
Chimney Fires
The result of excessive creosote buildup is a chimney re.
Chimney res are dangerous. Chimney inside temperatures
can exceed 2000° F. This causes much higher than normal
temperatures in the chimney and on its exterior surfaces.
Thus ignition of nearby or touching combustible material
is more likely during a chimney re. Proper clearances are
critical during such a re.
Chimney res are easy to detect; they usually involve one or
more of the following:
-Flames and sparks shooting out of the top of the chimney
-A roaring sound
-Vibration of the chimney
In Case of a Chimney Fire
1. Prepare to evacuate to ensure everyone's safety. Have
a well understood plan of action for evacuation. Have a
place outside where everyone is to meet.
2. Close air inlet on stove.
3. Call local re department. Have a re extinguisher handy.
Contact your local municipal or provincial re authority for
further information on how to handle a chimney re. It is
most important that you have a clearly understood plan
on how to handle a chimney re.
4. After the chimney re is out, the chimney must be cleaned
and checked for stress and cracks before starting another
re. Also check combustibles around the chimney and
the roof.
- The services of a competent or certied installer, (certied
by the Wood Energy Technical Training program (WETT) - in
Canada,Hearth Education Foundation (HEARTH) - in U.S.A.,)
are strongly recommended.
Avoiding a Chimney Fire
There are two ways to avoid chimney res:
1. Do not let creosote build up to a point where a big chimney
re is possible.
2. Do not have res in the heater that may ignite chimney
res. These are hot res, such as when burning household
trash, cardboard, Christmas tree limbs, or even ordinary
fuel wood; (e.g.. with a full load on a hot bed of coals and
with the air inlet excessively open.)
Safety

4 NEO16 241013-20
CAUTION: Never use gasoline, gasoline type lantern fuel,
kerosene, charcoal lighter uid or similar liquids to start or
"freshen up" a re in this heater. Keep all such liquids well
away from the heater while it is in use.
CAUTION: Hot while in operation. Keep children, cloth-
ing and furniture away. Contact may cause skin burns.
Your PACIFIC ENERGY heater is designed for many years of
trouble free operation. Over ring the appliance will shorten
the life of the product.Failure to recitify an over ring condition
can be hazardous and may void the manufacturer's warranty.
Wood Selection
This heater is designed to burn natural wood only. Higher ef-
ciency and lower emissions generally result when burning
air-dried seasoned hardwoods, as compared to softwoods
or to green or freshly cut hardwoods.
Wood should be properly air dried (seasoned) for six months
or more. Wet or undried wood will cause the re to smoulder
and produce large amounts of creosote. Wet wood also pro-
duces very little heat and tends to go out often.
DO NOT BURN :
-Salt water wood * -Treated wood
-Wet or green wood -Coal/charcoal
-Garbage/Plastic * -Solvents
* These materials contain chlorides which will rapidly
destroy metal surfaces and void warranty.
Do not burn anything but wood. Other fuels, eg. charcoal,
can produce large amounts of carbon monoxide, a tasteless,
odourless gas that can kill. Under no circumstances should
you attempt to barbecue in this heater.
How to Test Your Wood
Add a large piece of wood to the stove when it has a good
large bed of coals. It is dry if it is burning on more than one
side within one minute. It is damp if it turns black and lights
within three minutes. If it sizzles, hisses and blackens without
igniting in ve minutes it is soaked and should not be burnt.
Lighting for the First Time
Curing of the Paint Finish
To achieve the best nish, the paint on your stove must be
baked on. When burning your stove for the rst 2-3 times it
is very important that the room be well ventilated. Open all
windows and doors. Smoke and fumes caused by the curing
process may cause discomfort to some individuals.
Lighting a Fire
WARNING: Never use chemicals or any other volatile
liquid to start a re.
1. Adjust air control to “High” position(all the way to the left)
and open door.
2. Place crumpled newspaper in the centre of the heater
and criss-cross with several pieces of dry kindling. Add
a few small pieces of dry wood on top.
3. Ignite the paper and close the door.
4. After the re has established itself, open the door and add
a few small logs. Close door.
5. Begin normal operation after a good coal base exists and
wood has charred.
Normal Operation
1. Set air control to a desired setting. If smoke pours down
across the glass (waterfall effect) this indicates you have
shut the control down too soon or you are using too low a
setting. The wide range control makes nding the desired
setting for your application easy. As every home's heat-
ing needs vary (ie. insulation, windows, climate, etc.) the
proper setting can only be found by trial and error and
should be noted for future burns.
2. To refuel, adjust air control to “High” position(all the way
to the left), and give the re time to brighten. Open the
door slowly, this will prevent backpuffing or ame roll-out.
3. Use wood of different shape, diameter and length ( recom-
mended 16"). Load your wood and try to place the logs
so that the air can ow between them. Always use dry
wood.
4. Do not load fuel to a height or in such a manner that would
be hazardous when opening the door.
5. For extended or overnight burns, unsplit logs are preferred.
Remember to char the wood completely on "High" set-
ting before adjusting air control to the "Low" setting for
overnight burn.
WARNING: Always keep loading door closed when burn-
ing. This heater is not designed for open door burning.
WARNING: No alteration or modication of the combus-
tion air control assembly is permitted. Any tampering
will void warranty and could be very hazardous.
WARNING: Do not use grates or andirons to elevate the
fuel. Burn directly on the re bricks. Replace broken or
missing bricks. Failure to do so may create a hazardous
condition.
Operation

241013-20 NEO16 5
Ash Removal
Caution: Ashes are to be removed only when the heater is cold.
Whenever ashes get 3 to 4 inches deep in your rebox, and
when re has burned down and cooled, remove excess
ashes. Leave an ash bed approximately 1" (25 mm) deep
on the rebox bottom to help maintain a hot charcoal bed for
future res.
Optional Ash Cleanout system: The ash dump handle is
located under the ash lip on the left hand side behind the
lower grill. To operate ash dump, remove the lower grill, pull
handle out 1/2" and turn clockwise. This will unlock the ash
dump and allow it to open. Hold handle open while pulling
ashes into the opening. Avoid large embers as these still
contain heat value. Release handle and push in to lock.
Ensure ash dump door is properly engaged. Fill the cavity
with the remaining ash level with the rebox oor. Lift and pull
out ashpan and discard ashes into metal container. Replace
ashpan and ensure it is seated properly.
Do not burn with ash dump door open. Doing so will
create a hazardous condition. Always leave about 1" of
ash when cleaning.
Disposal of Ashes
Ashes should be placed in a metal container with a tight t-
ting lid. The closed container of ashes should be placed on
a non-combustible oor or on the ground, well away from all
combustible materials, pending nal disposal. If the ashes
are disposed of by burial in soil or otherwise locally dispersed,
they should be retained in closed container until all cinders
have thoroughly cooled. Other waste should not be placed
in this container.
Storing Wood Beneath Unit
It is possible to store wood between the stove pedestals, un-
derneath the unit. The wood must not extend further forward
than ush with the pedestals. Do not store paper or other
stove lighting devices within the pedestal area. Although this
is possible it is not recommended. NOTE: Refer to local re
codes, CAN-B365 and NFPA 211 in the U.S..
WARNING: IFYOU CHOOSETO STOREWOOD BENEATH
YOUR UNIT,EXERCISE EXTREME CAUTIONWHEN LOAD-
ING THE WOODSTOVE. EMBERS CAN FALL AND MAY
IGNITE WOOD BENEATH STOVE.
Restarting After Extended or Overnight
Burns
1. Open door and rake hot embers towards the front of the
heater. Add a couple of dry, split logs on top of embers,
close door.
2. Adjust air control to high and in just a few minutes, logs
should begin burning.
3. After wood has charred, reset air control to desired setting.
4. To achieve maximum ring rate, set control to “High”
position(all the way to the left). Do not use this setting
other than for starting or preheating fresh fuel loads.
DO NOT OVERFIRE THIS HEATER: Attempts to achieve
heat output rates that exceed heater design specica-
tions can result in permanent damage to the heater and
chimney.
Over Firing
Over ring can be caused by operating the unit with the door
open, damage to door gaskets allowing excess air to enter
the rebox, the use of kiln dried lumber, mill ends or paper
waste and prolonged or continual use on a high burn setting.
More Wood, More Heat
Seasoned wood has approximately 7500 BTU's per pound.
If you put 10 pounds of wood in your stove for an eight hour
burn the wood will be producing 9375 BTU's per hour. (7500
BTU x 10 lbs./8hrs.=9375 BTU's per hr.) If you put 20 lbs of
wood in your stove for eight hour burn you will get 18,750
BTU's per hr. (7500 BTU x 20lbs./8hr.=18,750 BTU's per hr.).
This is only an example and is based on 100% efficiency. In
reality, your stove should perform above the 80% range.
Experience will give you the right settings for proper com-
bustion and efficient burning. Remember the correct air inlet
setting is affected by variables such as type of wood, outside
temperature, chimney size and weather conditions. With
practice, you will become procient in operating your heater
and will obtain the performance for which it was designed.
Proper Draft
1. Draft is the force which moves air from the appliance up
through the chimney.The amount of draft in your chimney
depends on the length of the chimney, local geography,
nearby obstructions and other factors.
2. Too much draft may cause excessive temperatures in the
appliance. An uncontrollable burn or a glowing red stove
part or chimney indicates excessive draft.
3. Inadequate draft may cause backpuffing into the room
and plugging of the chimney. Smoke leaking into the room
through appliance and chimney connector joints indicates
inadequate draft.

6 NEO16 241013-20
1. Burn wood only, dry and well seasoned. The denser or
heavier the wood when dry, the greater its heat value. This
is why hardwoods are generally preferred. Green or wet
wood will cause a rapid buildup of creosote. If you feel
it is necessary to burn wet or unseasoned wood, do so
only with the air inlet set open enough to maintain a good
strong re and fairly high chimney temperatures. Do not
attempt to burn overnight using green wood or wet wood.
Wet wood can cause up to 25% drop in heater output, as
well as contributing signicantly to creosote buildup.
WARNING: Never use chemicals or any other volatile
liquid to start a re. Do not burn garbage, or am-
mable uids such as gasoline, naptha, or engine oil.
We strongly recommend that smoke detectors be
installed.
2. Remove ashes frequently. Embers can roll out the door
and create a re hazard. Maintain a 1" minimum ash
base.
3. If glass becomes darkened through slow burning or poor
wood, it can readily be cleaned with replace glass cleaner
when stove is cold.Never scrape with an object that might
scratch the glass. The type and amount of deposit on the
glass is a good indication of the ue pipe and chimney
buildup. A light brown dusty deposit that is easily wiped off
usually indicates good combustion and dry, well-seasoned
wood and therefore relatively clean pipes and chimney.
On the other hand, a black greasy deposit that is difficult
to remove is a result of wet and green wood and too slow
a burning rate. This heavy deposit is building up at least
as quickly in the chimney.
WARNING: ONLY USE MATERIALS AND COMPO-
NENTS SUPPLIED BY MANUFACTURER WHEN
DOING MAINTENANCE OR REPLACEMENTS.
4. DOOR GASKETS -The gasket used on this unit (5/8" me-
dium density berglass rope) requires only light pressure
to seal. This will prolong seal life. It is important that the
door seal be maintained in good condition. Periodically
inspect seals and replace if necessary. Follow instruc-
tions included in the WODC.DG58 kit obtainable from
your nearest Pacic Energy Dealer.
5. DOOR GLASS - Do not slam loading door or otherwise
impact glass. When closing door, make sure that no logs
protrude to impact the glass. If the glass gets cracked or
broken, it must be replaced before using the stove.
Replacement glass can be obtained from your dealer.
Use 16-1/2" x 10-1/2" x 5 mm. Ceramic glass only. Do
not substitute with any other type.
To remove broken glass, remove the door gasket and then
undo the eight screws securing the gasket guides and glass
retainers. Remove all particles of glass . Be careful as they
are very sharp. Install new glass complete with gasket. Re-
place glass retainers and gasket guides then install new door
gasket as per instructions provided with the door gasket kit.
CAUTION:
- do not overtighten, tighten screws very carefully
- do not clean glass when hot
- do not use abrasive cleaners on glass
6. The area where boost combustion air enters the rebox
must be kept clear of excessive ash buildup which will
block air ow. This area is at the front of the rebox.
7. Do not store wood within heater installation clearances, or
within the space required for fuel loading and ash removal.
Keep the area around the heater clean and free of loose
combustibles, furniture, newspapers, etc.
8. Establish a routine for the fuel, woodburning and ring
technique. Check daily for creosote buildup until experi-
ence shows how often you need to clean to be safe.
9. Be aware that the hotter the re, the less creosote is
deposited. Weekly cleaning may be necessary in mild
weather, even though monthly cleaning is usually enough
in the coldest months when burning rates are higher.
10. Instruct all members of your family on the safe operation
of the heater. Ensure they have enough knowledge of the
entire system if they are expected to operate it. Stress the
section on chimney res and the importance of following
the steps outlined "In Case of Chimney Fire".
Baffle Removal
Chimney connector pipe should be disconnected from stove
to clean and inspect. Only if this is not possible should you
remove baffle assembly.CAUTION:Ceramic blanket insulation
is located on top of baffle. Do not use a vacuum in this area.
DO NOT OPERATE WITH BAFFLE ASSEMBLY OR
INSULATION REMOVED.
Remove retaining pin at the back top of the rebox, just under
the baffle. Lift baffle up and pull forward to disconnect from
the supply tube. Tilt baffle sideways to drop down and remove
from rebox. Re-install baffle assembly in reverse order.
Maintenance

241013-20 NEO16 7
Maintenance Checks
Check the following parts for damage such as cracks, excessive corrosion, burned out sections and
excessive warping: (See website for descriptions and more detail)
Some warping of the baffle is normal(up to 1/4” or .65cm). Replace if the baffle has permanent warp-
ing greater than this or has signs of cracking or breakage.
Weekly:
- Firebrick - for cracking.
- Door Gasket - sagging, placement, damage.
Monthly:
- Brick rail tabs and brick rails.
- Air riser tube in the back of the rebox.
- Back side of airwash chamber - located in the upper front of rebox.
- Baffle locking pin.
- Boost tube cover - located in center of manifold, bottom front of rebox.
When Cleaning the
Chimney System:
- Top baffle board/blanket.
- Baffle.
- Brick Rails.
- Manifold - located in bottom front of rebox.
Blower:
- The blower should be cleaned out a minimum every six months by using a vacumn on the grill open-
ings in the back and bottom of the blower casing to remove any dust and debris.
- Please contact your dealer if you experience any of the damage listed above. Continuing to operate
your stove with broken parts may accelerate damage to other parts and may void your warranty

8 NEO16 241013-20
36 15/16"
36"
27 1/8"
20 1/8"
17 7/16"
6"
NEO 1.6 Dimensions
Crate Removal
1) Carefully remove wood top and supports.
2) Remove plastic cover.
3) Using a 7/16" wrench, remove lag bolts that secure stove
body to bottom pallet.
Side Panel Installation
1) Remove the upper grill by removing the two screws secur-
ing it to the rebox. Fig. #1
2) Carefully remove the panels from the box.
FIG. #1
SCREWS
Assembly
NOTE: DIMENSION
DOES NOT INCLUDE
LEVELLING LEGS
LAG BOLTS

241013-20 NEO16 9
3) Engage the tabs in the panel into the slots in the panel
mounting bracket. Fig. #2
4) Attach the panel to the rear shield.Secure with two screws.
Fig. #3
FIG. #2
FIG. #3
SCREWS

10 NEO16 241013-20
8" [203mm]
16" [406mm]
8" [203mm]
Canada Only
Floor Protector
The stove may be installed on a combustible oor provided
noncombustible ember protection is used.
This protection must extend as follows:
In Canada: 18" (457 mm) on the ring side and 8" (203 mm)
to the other sides. See Figure #4, below.
Combustion Air
Intake or combustion air can be supplied to the stove in one
of two ways. Consult your local building code or CAN/CSA-
B365, Installation Code for Solid-Fuel-BurningAppliances and
Equipment before proceeding. The unit must have adequate
air for combustion provided in the room the unit is installed in.
1. Outside air supply - (Necessary for mobile home instal-
lation, optional for residential installation.) Outside air
may be drawn from either underneath the stove or from
behind.
To draw outside air through the oor, leave the 4" knockout
or cover plate in place in the rear of the ash box enclosure.
Cut or drill a 4" diameter hole directly below the bottom
hole of the ash box enclosure. Connect enclosure to the
oor with a short 4" diameter pipe. If you wish to connect
the outside air to the rear hole on the ash box, then remove
the 4" knockout or cover plate at the rear of the ash box.
This hole must get its air from a ventilated crawl space
or be extended with duct to the outdoors (see Figure #8,
Page 13). The use of outside combustion air for residential
installation requires the unit to be secured to the structure
to prevent dislodging of the air duct.
To draw outside air from behind the stove, an outside air
adaptor may be required (see Optional Blower section).
Cut or drill a 4" hole through a wall behind the unit. Use
an appropriate household 4" inlet.
Note: This unit is not designed to be operated with the ring
door open. In addition to the obvious hazard of sparks
landing on combustibles, an open re door will cause
the heater to draw air from the living space and possibly
cause suffocation.
2. Room air supply - Remove the cover plate or knockout
from the rear of the ash box enclosure. The stove will
now draw its air from the room through this opening and
into the rebox intake.
Note: The living space around the heater must be well
ventilated with good air circulation. Anything that may
cause a negative pressure can cause gases or fumes
to be pulled into the living area. During extremely cold
weather, and especially when burning at very slow rates,
the upper parts of the exposed chimney may ice up,
partially blocking the ue gases. If blockage occurs, ue
gases may enter living space.
Note: An outside air pipe shield is provided to place in front of
the 4"pipe used to bring outaide air into the unit. Instructions
for instalaltion are provided with the shield.(Part #NE16.7872)
U.S.A. Only
Non-combustible
oor protector
FIG. #4
FIG. #5
In USA: 16" (406 mm) to the front and 8" (203 mm) to the
sides of the fuel loading door opening. See Figure #5, below.
This protection is also required under the chimney connector
and 2" (51 mm) beyond each side when using horizontal pipe.
8" [203mm]
18" [457mm]
8" [203mm]
8" [203mm]
Minimum Width - 43 1/8'
Minimum Overall Depth - 45 5/8"
Non-combustible
oor protector
Minimum Width - 33 3/8"
Minimum Overall Depth - 32 3/4"

241013-20 NEO16 11
Warning:Under no circumstances is this heater to be installed
in a makeshift or "temporary" manner. It may be red only
after the following conditions have been met.
* DO NOT ATTEMPT TO CONNECT THIS HEATER TO
ANY AIR DISTRIBUTION DUCT.
* Outside combustion air or fresh air into the room may be
required in your area, consult local building codes (see
Combustion Air section).
- The services of a competent or certied installer, (certied
by the Wood Energy Technical Training program (WETT) - in
Canada,Hearth Education Foundation (HEARTH) - in U.S.A.,)
are strongly recommended.
BOTH CHIMNEY SYSTEM AND CONNECTOR MUST BE
LISTED TO:
IN CANADA - ULC S-641 LISTED CONNEC-
IN CANADA - ULC S-641 LISTED CONNEC-
TOR AND ULC-S-629 LISTED CHIMNEY,
TOR AND ULC-S-629 LISTED CHIMNEY,
IN USA- UL-103
IN USA- UL-103
HT LISTED CONNECTOR AND CHIMNEY
HT LISTED CONNECTOR AND CHIMNEY
Clearances
1. This heater may be installed using a single-wall connector
(smoke pipe) or listed double-wall connector (see Mobile
Home installation).
2. Clearances to combustible surfaces and materials using
single-wall connector are shown in Figure #7, page 12.
Clearances may be reduced with various heat insulating
materials. Consult local re codes and authorities for ap-
proval.
3. Alternately, for close clearances, use a listed double-wall
connector. See Fig #6, page 12.
It is possible to store wood between the stove supports, un-
derneath the unit. The wood must not extend further forward
than ush with the supports. Do not store paper or othe stove
lighting devices within the pedestal area.Although this is pos-
sible it is not recommended. NOTE: Refer to local re codes,
CAN-B365 and NFPA 211 in the U.S..
WARNING: IFYOU CHOOSETO STOREWOOD BENEATH
YOUR UNIT,EXERCISE EXTREME CAUTIONWHEN LOAD-
ING THE WOODSTOVE. EMBERS CAN FALL AND MAY
IGNITE WOOD BENEATH STOVE.
Chimney and Connector
Connect to a listed chimney or a chimney suitable for use
with solid fuel that is lined and in good condition and meets
local building codes. The chimney ue size should be the
same as the stove outlet for optimal performance. Reduc-
ing or increasing the ue size may adversely affect stove
performance. Chimney ue exit is to be 3 feet (1 m.) above
roof and two feet (0.6 m.) above highest projection within 10
feet (3 m.). The installation must meet all local codes. Do not
connect this unit to a chimney ue serving another appliance.
Minimum system height is 15 feet (4.6 m.) (measured from
base of appliance).
Double-Wall Connector
- Use a listed double-wall connector.
- Install all components to the chimney connector manu-
facturer's installation requirements.
Single-Wall Connector
Smoke pipe must be:
* as short and straight as possible, use six inch
diameter, 24 gauge black pipe that is clean and in new
condition.
* secured at every joint and collar with 3 sheet metal screws.
* installed with the crimped or male ends pointing down.
This will carry any liquid creosote or condensation back
into the stove.
* The chimney connector shall not pass through an attic, roof
space, closet or similar concealed space, oor, or ceiling.
Where passage through a wall, or partition of combustible
material is desired, the installation shall conform to CAN/
CSA-B365, Installation Code for Solid-Fuel-BurningAppli-
ances and Equipment or in the U.S., NFPA 211: Standard
for Chimneys, Fireplaces, Vents, and Solid Fuel-Burning
Appliances.
Procedure
1. If a listed chimney and double-wall connector is to be
connected to the stove, install all components to the chim-
ney manufacturer's installation requirements. (Outside
combustion air may be required, consult local building
codes. See Combustion Air section on page 10.)
2. If it is desirable to use smoke pipe in conjunction with the
insulated chimney, see step 4.
3. If a roof or ceiling support is used in the installation, you
will nd the chimney manufacturer's complete instructions
packed with the roof support.
4. To start installing smoke pipe (chimney connector), slip
crimped edge of the pipe inside the stove collar. Use
holes provided in collar to secure pipe with three screws.
5. Install the remaining lengths of pipe one on top of the
other to the nished height of the chimney connector and
secure to each other.
Residential Installation

12 NEO16 241013-20
5"
21 1/2"
11" 8" 3"
15"
3"
Mobile Home
Minimum
Clearance to
Combustibles
Warning: Under no circumstances is this heater to be installed
in a makeshift or "temporary" manner. It may be red only
after the following conditions have been met.
- DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE
SERVING ANOTHER APPLIANCE.
- DO NOT INSTALL IN A SLEEPING ROOM.
- BOTH CHIMNEY SYSTEM AND CONNECTOR MUST BE
LISTED TO:
IN CANADA - ULC S-641 LISTED CONNEC-
IN CANADA - ULC S-641 LISTED CONNEC-
TOR AND ULC-S-629 LISTED CHIMNEY,
TOR AND ULC-S-629 LISTED CHIMNEY,
IN USA - UL-103 HT LISTED CONNECTOR
IN USA - UL-103 HT LISTED CONNECTOR
AND CHIMNEY
AND CHIMNEY
- Outside air supply must be used for Mobile Home installa-
tions see Figure #8, Page 13.
- Remove the chimney down to the roof ashing to allow for
transportation of the mobile home.
FIG. #6
Double Wall Connector - Residential
Single Wall Connector - Residential
Alcove: Min. Height 7'
Max. Depth 3'
Double Wall Connector - Mobile Home
Clearances
This heater must be installed with a listed double-wall con-
nector and compatible chimney system.
Clearances to combustible surfaces and materials are shown
in Figure #7 below.
Clearances may be reduced with various heat insulating ma-
terials. Consult local re codes and authorities for approval.
NOTE: Longer chimney lengths and different pitch ashings
may be used. All other parts listed must be installed (see
Figure #8, Page 13). Install all components to the connector
or chimney manufacturer's installation requirements.Consult
your chimney supplier for installation advice.
18" 12"
12"
25 1/2"
20"
8"
8"
11"
8"
21 1/2"
8"
11" 5" 5" 8" 15"
21 1/2"
3"
3"
Residential
Minimum
Clearance to
Combustibles
FIG. #7
Mobile Home Installation

241013-20 NEO16 13
FIG. #8
Chimney
Roof ashing
Storm collar
* 4" diameter air inlet with rodent screen
* If the crawl space is well ventilated
it is not necessary to extend air inlet to
outside
Spark arrestor
rain cap
Radiation shield
Chimney Connector
Chimney Support
47.5" (1207 mm)
Minimum
Minimum 7' (2.1m.)
Ceiling Height
Attachment to oor for
mobile homes
Non-combustible
oor protector
48"
(1219 mm)
3' (914 mm)
Minimum
Hooded vent or
90 elbow turned down
The chimney may incorporate
an offset. To do this safely, all
sections of listed connector,
offset elbows and chimney
section must be screwed
together by at least three
sheet metal screws per joint.
The chimney must be suitably
supported by the chimney
manufacturer's listed offset
support.
Procedure:
CAUTION: THE STRUCTURAL INTEGRITY OF THE MO-
BILE HOME FLOOR, WALL AND CEILING/ROOF MUST
BE MAINTAINED.
- The services of a competent or certied installer, (certied
by the Wood Energy Technical Training program (WETT) - in
Canada,Hearth Education Foundation (HEARTH) - in U.S.A.,)
are strongly recommended.
Note: See "Combustion Air" section on page 10.
1. Position stove and oor protection with hole for combus-
tion air in accordance with the clearances as stated on
the label and in Figure #7.
2. Mark the position for the hole in the ceiling and roof by
using a string and plumb-bob.
3. Check that the intended location will not interfere with oor
joists, ceiling joists or rafters before proceeding further.
4. Cut a hole in the ceiling and roof to suit the chimney
system and frame in the sides. The chimney support is
mounted to the framing.
5. If the chimney connector exits the mobile home less then
7 feet above the ground then a guard must be installed
to cover the connector up to a height of 7 feet.
6. The guard must not have opening larger than 3/8" and
must maintain a space of 4" minimum around the chimney
connector.
7. Assemble chimney sections so the nished length is rest-
ing on the support and protruding through the roof.Avoid
having joints between ceiling and roof. Install radiation
shield.Assemble ashing and storm collar and be sure to
maintain the vapour barrier at this point. (Seal securely.)
Attach rain cap and check ashing for leaks.
8. Install connector as per manufacturer's instructions.
9. Attach stove to ooring using two 1/4" x 2" or longer lag
screws.
Alternate up and
out installation
12"(305mm)
Minimum rst
section of pipe.
12"(305mm)
Minimum Wall Thimble
Unit may be harder to start.
Please provide as much verti-
cal length for the rst section
of pipe as possible.
*
*

14 NEO16 241013-20
The optional blower kit (WODC.BLOW) is equipped with a
three prong power cord and may be installed at any time.
Follow installation instructions supplied with the kit. Route
power supply cord away from heater.
Electrical rating: 115 volts A.C., 60Hz, .5 amps.
Fan output rating: 125 CFM
Blower Operation
Proper blower speed matched with air control setting will en-
sure peak performance from your stove. Operate as follows:
- Air control set to "L" (low), operate blower speed control
on "Low".
- Air control set between "L" and "H" (low and high), oper-
ate blower speed control at desired setting.
Automatic: To operate the blower automatically, set the
rocker switch on the side of the fan housing to "Auto" and set
the speed control to desired setting. This will allow the fan to
turn on as the stove heats up to operating temperature. It will
also shut the blower off after the re has gone out and the
unit cooled to below a useful heat output range.
Manual: To manually operate the blower, set the rocker switch
to "Man" and set the speed control to desired setting.This will
bypass the sensing device and allow full control of the blower.
Switching from "Auto" to "Man" or selecting speed may be
done anytime.
Optional Outside Air Adaptor
The adaptor is only required if the blower kit is to be installed
and outside combustion air to be ducted to rear of pedestal.
Installation:
Remove blower kit if already installed. Place adaptor with
the 4" round hole facing up and opposite end covering the
room air knockout hole on the back of the pedestal. Mark
attachment holes on pedestal base and drill with 1/8" bit. At-
tach with #8 x 1/2" screws and reinstall fan. Combustion air
duct from outside can now be attached to the 4" round collar.
Optional Blower

241013-20 NEO16 15
Troubleshooting
Problem Cause Cure
Glass is Dirty 1. Wood is wet - Use dry wood
2.Turning down air control - Do not turn down until
or damper too soon a) there is a good bed of coals
b) the wood is charred
3.Draft too low - Improper chimney height and / or diameter
- Chimney plugged or restricted, check ue
- Provide outside air for combustion
4. Door gasket leakage - Replace gasket
- Check latch
Excessive Creosote Buildup - See 1,2,3, above.
Low Heat Output 1. Wood is wet - Use dry wood
2.Fire too small - Build a larger re
3.Draft too low - Chimney plugged or restricted, inspect and clean
Stove Won't Burn 1. Combustion air supply blocked - Check outside air supply for obstruction
- Check that room air cover is removed
2.Draft too low - Chimney plugged or restricted, inspect and clean
- Chimney oversized or otherwise unsuitable,
consult Dealer

16 NEO16 241013-20
Replacement Parts - NEO 1.6
(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)
ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO.
2............Embossed Panel Set.................... NE16.78375XX
3............Door Catch .......................................... NE16.7825
4............Ash Lip .......................................... NE16.5037701
5............Glass Retainers (4 pc.)..................... NE16.78185
6............Gasket Guides (4 pc.) ........................ NE16.7818
7............Replacement Glass (c/w Tape) .... NE16.5034700
8............Door Gasket Kit............................... WODC.DG58
9............Door Casting, Black....................... NE16.5037700
10..........Door Handle Assembly........................ NE16.7817
11..........Side Shield Bracket........................... NE16.78376
12.......... Firebrick Set ........................................NE16.BRIC
13.......... Brick Rail, Left/Right..................... NE16.RAILSET
14.......... Replacement Baffle Kit....................NE16.BAFKIT
15.......... Baffle Pin .........................................SSER.125001
16.......... Ash System ..................................... NE16.LGADA
17.......... Left Support, Black.............................NE16.78115
17b........ Right Support, Black ......................... NE16.78125
18.......... Ash Dump Assembly ........................... NE16.7857
19.......... Ash Drawer........................................ NE16.78352
20..........Air Shutter Assembly ........................... NE16.7826
21..........Secondary Air Control Assembly...........
NE16.7833
22..........Trivet.............................................. NE16.5037704
23..........Levelling Feet (4pcs.) .................... NE16.5049765
24..........Lower Grill Assy............................. NE16.5037703 All parts may be ordered from your nearest Pacic Energy dealer.
Contact Pacic Energy for the location of the dealer nearest you.
25..........Upper Grill..................................... NE16.5037702
*26........Outside Air Pipe Shield ....................... NE16.7872
Color Codes, XX:
Black ......BK Black Pearl.........BP
Ivory.......IY Coffee Brown.....CB
Blue........BE Copper...............CU
Red ........RD Titanium.............TI
2
2
3
4
5
6
7
8
9
10
11
11
12
13
14
16
17
18
19
20
21
22
23
24
25
17b
*NOT SHOWN

241013-20 NEO16 17
ish. This clean charcoal burning stage will last for
a considerable length of time and refuelling should
be avoided until the charcoal base has become
quite small.
OPERATING TIPS
1.Always use dry, seasoned rewood, up to 18" long.
Load wood, a mixture of large and small pieces,
on top of a good ash base (1" minimum).
2. Operate on a medium to
high setting, for up to 1 hour
from cold start. After the ini-
tial warm up period, refuel
and leave the air control
on a medium setting for
5 to 10 minutes more and
then set the air control to
the desired position.
3. If a slow burn is desired,
set the air control to low.
Active secondary burning
should be present above
the wood load. If it is not
present or goes out shortly
after, proper operating
temperature has not been
reached and the stove
needs additional warm
up time.
Understanding & Operating Your Pacic Energy Stove
The Pacic Energy line of woodstoves is a culmina-
tion of years of research and development. Designed
to be efficient, clean-burning and user-friendly, this
heater will give you years of warm service. However,
a knowledgeable operator is still the most important
factor for maximum performance and part of this is
understanding the basic functions of this design.
Traditional wood stoves had a basic combustion
system which allowed a considerable amount of
heat energy to escape up the
chimney as unburned gases
and particulates (smoke).
Pacic Energy has designed
a system that solves the
problem by burning the
smoke and releasing the
additional heat to the room.
This system has two critical
design features:
1. Above re secondary air
injection:
The hollow "air baffle" injects
super-heated secondary air
just above the load.With the
stove at the proper operating
temperature, this will create
a secondary ame that will
be evident for approximately
1/3 of the total burn time.
2. High mass and thermal insulation:
The high mass (weight) acts as a heat storage and
the thermal insulation keeps the combustion zone
hot. Active aming takes place during the rst part
of the burn. During this stage, heat is stored in the
mass of the unit and is later released slowly and
evenly. As wood chars, active aming will dimin-
1
2
3
5
6
4
1 -Boost Air 4 -Secondary Combustion Zone
2 -Main Combustion Air 5 -Radiant Heat
3 -Air Wash System 6 -Convected Heat

ITEM/ ARTICLE DIMENSIONS PART NUMBER/ NUMÉRO DE
PIÈCE
A 1 1/2” X 4 1/2” X 1 1/4” (39 mm x 115 mm x 32 mm) 248.0
B 3” X 4 1/2” X 1 1/4” (77 mm x 115 mm x 32 mm) 247.0
D 9” X 4 1/2” X 1 1/4” (230 mm x 115 mm x 32 mm) 5096.99
NEO 1.6
Firebrick Installation Instructions
This package contains 13 full-size firebricks, as well as 2 various cut-size bricks.
With the heater in the upright position, install firebricks as follows:
- Place 4 full-size firebricks at the back of the heater first.
- Next, install the side firebricks, 3 full-size each side as shown below.
- Lastly, install 3 full-size firebricks and bricks A & B as shown in the bottom of the firebox.
A
B
D

Label
A.
12 IN. / 305 MM 12 IN. / 305 MM
B.
<12 IN. / 305 MM <12 IN./305 MM
C.
8 IN. / 203 MM 8 IN. / 203 MM
D.
25.5 IN. / 597 MM 25.5 IN. / 597 MM
E.
<14.8 IN. / 325 MM <14.8 IN./325 MM
F.
16.8 IN. / 427 MM 16.8 IN. / 427 MM
A.
8 IN. / 203 MM 8 IN. / 203 MM
B.
5 IN. / 127 MM 5 IN. / 127 MM
C.
3 IN. / 76 MM 3 IN. / 76 MM
D.
18.4 IN. / 467 MM 18.4 IN. / 467 MM
E.
<7.8 IN. / 198 MM <7.8 IN. / 198 MM
F.
11.8 IN. / 300 MM 11.8 IN. / 300 MM
A. 8
IN. / 203 MM 8 IN. / 203 MM
B.
5 IN. / 127 MM 5 IN. / 127 MM
C.
N/A 3 IN. / 76 MM
D. 18.4
IN. / 467 MM 18.4 IN. / 467 MM
E.
7.8 IN. / 198 MM 7.8 IN. / 198 MM
F.
N/A 11.8 IN. / 300 MM
CERTIFIED FOR CANADA AND U.S.A. - SERIES / SÉRIE: AMODEL / MODÈLE: NEO 1.6 LISTED ROOM HEATER, SOLID FUEL TYPE. ALSO FOR USE IN MOBILE HOMES TESTED TO/ ÉPROUVÉ SELON: CAN/ULC S627-00 AND IN THE USA CONFORMS TO UL 1482-2011
• INSTALL AND USE IN ACCORDANCE WITH THE MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS. • CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS, INSTALLATION PERMIT AND INSPECTION IN YOUR AREA. • DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHERAPPLIANCE. • USE 6 INCH / 150MM DIAMETER MINIMUM 24 MSG BLACK OR LISTED CONNECTOR. • CAN BE CONNECTED TO A LINED MASONRY CHIMNEY SUITABLE FOR USE WITH SOLID FUELS. • DO NOT OBSTRUCT THE SPACE BENEATH THE HEATER. • SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED
WHEN PASSING A CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING.
• DO NOT PASS A CHIMNEY CONNECTOR THROUGH A COMBUSTIBLE WALL OR CEILING. • MINIMUM CLEARANCE BETWEEN SINGLE WALL CHIMNEY CONNECTOR AND COMBUSTIBLE MATERI-
ALS-18INCHES/455MM. CLEARANCE MAY BE REDUCED BY THE USE OF LISTED PIPE SHIELDS, WALL PROTECTORS OR OTHER MEANS APPROVED BY LOCAL BUILDING OR FIRE OFFICIALS.
• COMPONENTS REQUIRED FOR MOBILE HOME AND ALCOVE INSTALLATION: OUTSIDE AIR KIT. BOTH CHIMNEY SYSTEM AND CONNECTOR MUST BE LISTED TO:
IN CANADA - ULC S-641 LISTED CONNECTOR AND ULC-S-629 LISTED CHIMNEY
IN CANADA - ULC S-641 LISTED CONNECTOR AND ULC-S-629 LISTED CHIMNEY
IN USA - UL-103 HT LISTED CONNECTOR AND CHIMNEY
IN USA - UL-103 HT LISTED CONNECTOR AND CHIMNEY • USE COMPONENTS SPECIFIED IN PACIFIC ENERGY INSTALLATION INSTRUCTIONS. • OPTIONAL COMPONENTS - BLOWER(WODC.BLOW), FAN ELECTRICAL RATING: 115V, 60HZ, .5 AMP. DO NOT ROUTE POWER CORD BENEATH HEATER. • CAUTION: RISK OF EXCESSIVE TEMPERATURES - KEEP ASH DUMP CLOSED DURING FIRING OF THE
HEATER.
• OPERATE ONLY WITH FEED DOOR CLOSED. OPEN TO FEED FIRE ONLY. • KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIALS WELL AWAY FROM HEATER. • REPLACE GLASS ONLY WITH CERAMIC GLASS. HORIZONTAL CONNECTOR NOT PERMITTED IN MOBILE HOMES <
AS TESTED - PIPE SHIELD MAY BE REQUIRED BY LOCAL AUTHORITIES.
* COMBUSTIBLE ALCOVE SIZE : DEPTH - 3 FT. / .91 M MAX., HEIGHT 7 FT. / 2.1 M MIN., WIDTH 43 IN. / 1.09 M
MIN.
COMBUSTIBLE FLOOR MUST BE PROTECTED BY A CONTINUOUS NON-COMBUSTIBLE MATERIAL EX-
TENDED TO THE FRONT, SIDES AND BACK AS INDICATED.
• STOVE DESIGNED TO BURN CORDWOOD ONLY. BURNING OTHER MATERIALS MAY CAUSE DAMAGE TO
STOVE OR HOME.
MINIMUM CLEARANCES TO
COMBUSTIBLE MATERIALS/
DÉGAGEMENTS MINIMALES AUX
MATÉRIAUX COMBUSTIBLES
DO NOT REMOVE THIS LABEL
RACCORD
VERTICAL CONNECTOR
RACCORD
HORIZONTAL CONNECTOR
RESIDENTIAL CLOSE CLEARANCE INSTALLATION
USING DOUBLE WALL CONNECTOR/
INSTALLATION
RÉSIDENTIELLE AVEC DÉGAGEMENT MINIMAL, UTILISANT
UN RACCORD DE MUR DOUBLE
* ALCOVE INSTALLATION
USING DOUBLE WALL
CONNECTOR/
* INSTALLATION
EN ALCÔVE UTILISANT UN
RACCORD DE MUR DOUBLE
RESIDENTIAL INSTALLATION
USING SINGLE WALL CONNECTOR/
INSTALLATION RÉSIDENTIELLE UTILISANT UN
RACCORD DE MUR SIMPLE
IN CANADA G. 18 INCHES / 455 MM AU CANADA
H. 8 INCHES / 200 MM
I. 8 INCHES / 200 MM IN U.S.A. G. 16 INCHES / 405 MM
AUX ÉTATS-UNIS
H. 3.2 INCHES / 81 MM
I. 0 INCHES / 0 MM
MOBILE
HOME INSTALLATION
USING DOUBLE WALL
CONNECTOR/
INSTALLATION
EN MAISON MOBILE UTILISANT
UN RACCORD DE MUR DOUBLE
ETL#4001507
• INSTALLEZ ET UTILISEZ SELON LES INSTRUCTIONS D’INSTALLATION ET D’OPÉRATION FOURNI AVEC L’APPAREIL.. • CONTACTEZ LES OFFICIELS DE LA CONSTRUCTION OU DE SERVICE D’INCENDIE POUR DES INFORMATIONS QUANT AUX
RESTRICTIONS. PERMIS D’INSTALLATION ET INSPECTIONS DANS VOTRE RÉGION.
• NE RELIEZ PAS CET APPAREIL À UN CONDUIT DE CHEMINÉE DESSERVANT DÉJÀ UN AUTRE APPAREIL (ÉTATS-UNIS SEULE-
MENT).
• UTILISEZ UN RACCORDEMENT NOIR OU CLASSÉ DE 24 MSG ET AVEC UN DIAMÈTRE D’AU MOINS 6 POUCES / 150 mm. • PEUT ÊTRE CONNECTÉ À UNE CHEMINÉE DE MAÇONNERIE ALIGNÉE PRÊTE À L’EMPLOI AVEC DES COMBUSTIBLES SOLIDES. • CONSULTEZ LE CODE LOCAL DE CONSTRUCTION ET LES INSTRUCTIONS DU FABRICANT QUANTAUX PRÉCAUTIONS À
PRENDRE LORSQUE VOUS FAITES PASSER UNE CHEMINÉE À TRAVERS D’UN MUR OU D’UN PLAFOND COMPOSÉS DE MATÉ- RIAUX COMBUSTIBLES.
• NE FAITES PAS PASSER UN RACCORDEMENT DE CHEMINÉE À TRAVERS D’UN MUR OU D’UN PLAFOND COMPOSÉS DE MATÉ-
RIAUX
• DÉGAGEMENT MINIMAL ENTRE UN RACCORDEMENT DE CHEMINÉE À UN MUR SIMPLE ET TOUT MATÉRIEL COMBUSTIBLE - 18
POUCES / 455 mm. CE DÉGAGEMENT PEUT ÊTRE RÉDUIT EN UTILISANT DES PROTECTEURS DE TUYAUX CLASSÉS, PROTEC- TEURS DE MUR OU AUTRES MOYENS APPROUVÉS PAR LES OFFICIELS DE LA CONSTRUCTION OU DU SERVICE D’INCENDIE DE VOTRE RÉGION.
CONNECTEUR HORIZONTAL NON PERMIS DANS MAISONS MOBILES • L’APPARIEL DOIT COMPORTER UN ENSEMBLE POUR PIEDSTABLE OU SUR PATTES. • PIÈCES REQUISES POUR INSTALLATION EN MAISON MOBILE OU EN ALCÔVE: NÉCESSAIRE D’APPROVI-
SIONNEMENT D’AIR EXTÉRIEUR ET L’UN DES RACCORDS SUIVANTS: EN COMBINAISON AVEC L’UN DES SYSTÈMES DE CHEMINÉE COMPATIBLES SUIVANTS:
AU CANADA - LE ULC S-641 CONNECTEUR ENUMERES ET ULC-S-629 ONT ENUMERE CHEMINEE • PIÈCES EN OPTION - NÉCESSAIRES DE SOUFFLERIE, INDICES ÉLECTRIQUES DE SOUFFLERIE: 115V, 60HZ, 1.0 AMP. LE FIL
ÉLECTRIQUE NE DOIT PAS ÊTRE PLACÉ SOUS LE POÈTE.
LE FIL ÉLECTRIQUE NE DOIT PAS ÊTRE PLACÉ SOUS LE POÊLE • ATTENTION: RISQUE DE TEMPÉRATURES EXCESSIVES - GARDES LE TIROIR DE CENDRES FERMÉ PENDANT L’ALLUMAGE DU
POÈTE.
• OPÉREZ SEULEMENT LORSQUE LA PORTE D’ALIMENTATION EST FERMÉE. • OUVREZ SEULEMENT POUR ALIMENTER LE FEU. • GARDEZ LES MEUBLES ET AUTRES MATÉRIAUX COMBUSTIBLES BIEN ÉLOIGNÉS DU POÊLE. • REMPLACES LA VITRE AVEC UNIQUEMENT DE LA VITRE CÉRAMIQUE. CONNECTEUR HORIZONTAL NON PERMIS DANS MAISONS MOBILES <
TEL QUO ÉPROUVÉ UN PROTECTEUR DE TUYAU PEUT ÊTRE REQUIS PAR LES AUTORITÉS LOCALES
* DIMENSION D’ALCOVE COMBUSTIBLE: PROFONDEUR - 3 PIEDS / .91M, HAUTEUR 7 PIEDS/2.1M, LARGEUR 4 PIEDS/1.2M MINI-
MUM.
LE PLANCHER COMBUSTIBLE DOIT ÊTRE PROTÉGÉ PAR UN MATÉRIEL NON-COMBUSTIBLE TOUT D’UNE PIÈCE QUI DOIT
S’ÉTENDRE DE PAR LE DEVANT, LES COTÉS ET L’ARRIÈRE TEL QU’INDIQUÉ.
· LE FOURNEAU CONÇU POUR BRÛLER CORDWOOD SEULEMENT. LA COMBUSTION D’AUTRES MATÉRI-
ELS PEUT.
A. SIDEWALL TO UNIT/
MUR DE CÔTE / APPAREIL
B. BACKWALL TO UNIT/ M
UR DE FOND / APPAREIL
C. CORNER TO UNIT/ COIN / APPAREIL D. SIDEWALL TO CONNECTOR/ MUR DE CÔTE / RACCORD E. BACKWALL TO CONNECTOR/ MUR DE FOND / RACCORD F. CORNER TO CONNECTOR/ COIN / RACCORD
BACK I
HEATER
G
SIDE
H
FRONT
SIDE
H
COTE
COTE
DEVANT
POELE
DOS
RACCORD
VERTICAL CONNECTOR
RACCORD
HORIZONTAL CONNECTOR
MADE IN CANADA/
FABRIQUÉ AU CANADA
J F M A M J J A S O N D
2013 2014 2015 2016 2017 2018
DATE OF MANUFACTURE/
DATE DE MANUFACTURE
NE16-1
U.S. ENVIRONMENTAL PROTECTION AGENCY CERTIFIED TO COMPLY WITH JULY, 1990, PARTICULATE EMISSION STANDARDS//
CERTIFIÉ PAR L’AGENCE DE PROTECTION DE
L’ENVIRONNEMENT DES ÉTATS-UNIS (EPA) EN ACCORD AVEC LES STANDARDS D’ÉMISSION DE PARTICULES DE JUILLET 1990
5050.700060513
MANUFACTURED BY/
FABRIQUÉ PAR:
PACIFIC ENERGY FIREPLACE PRODUCTS LTD.
2975 ALLENBY RD., DUNCAN, BC V9L 6V8
HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS. SEE NAMEPLATE AND INSTRUCTIONS.//
CHAUD LORSQU’EN OPÉRATION. NE PAS TOUCHER, TENEZ LES
ENFANTS ET LES VÊTEMENTS BIEN À L’ÉCART. LE CONTACT PEUT CAUSER DES BRÛLURES À LA PEAU. CONSULTEZ LA PLAQUE CE CONSTRUCTEUR ET LES INSTRUCTIONS.
CAUTION
ADJACENT WALL
BACK WALL
D
A
SIDE WALL
BE
ADJACENT WALL
F
C
MUR COTE
MUR ARRIERE
MUR ADJACENT
MUR ADJACENT
402

PACIFIC ENERGY FIREPLACE PRODUCTS LTD.
2975 Allenby Rd., Duncan, B.C. V9L 6V8
Phone: [phone]
Web site: http://www.pacicenergy.net
Printed in Canada