Whalen Kellum WMFP48EC-26GR User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2020-07-10 Rev. 0001-A
Kellum Media Fireplace Console
Stock # WMFP48EC-26GR
# WMFP48EC-26BR
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Kellum Media Fireplace Console
MODEL # WMFP48EC-26BR / WMFP48EC-26GR
How to adjust the European adjustable hinges on doors
Shipping may cause doors to go out of alignment. If you find that the doors need to be adjusted slightly,
turn the appropriate screw, as illustrated.
1. TO ADJUST DOOR FORWARD OR BACKWARD.
2. TO ADJUST DOOR TO RIGHT OR TO LEFT.
3. TO ADJUST DOOR UP OR DOWN.
MAXIMUM LOAD 50 lb. (22.7 kg)
1
2
M A X I M U M R E C O M M E N D E D W E I G H T L O A D
S
FITS UP TO MOST 58” DIAGONAL FLAT
PANEL TVs
MAXIMUM LOAD 70 lb. (31.8 kg)
PLACE TV BEHIND THE STOPPER
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS.
NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR EQUIPMENT. TO
AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTER OF THE UNIT; THE BASE OF THE
TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE UNIT WITHOUT
OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS
INCLUDING OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS
COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY. FOR USE WITH
TELEVISIONS WEIGHING 70 LBS (31.8 KG) OR LESS. USE WITH HEAVIER TELEVISIONS MAY RESULT IN
INSTABILITY CAUSING TIP OVER RESULTING IN DEATH OR SERIOUS INJURY

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the fireplace.
XX
FINAL
1 2 43

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Upper Side Panel (Qty. 2) C- Upper Front Panel (Qty. 2)
D- Upper Partition Panel (Qty. 1) E- Center Shelf (Qty. 1) F- Left Lower Side Panel (Qty. 1)
G- Right Lower Side Panel H- Left Lower Partition Panel I- Right Lower Partition Panel
(Qty. 1) (Qty. 1) (Qty. 1)
J- Lower Back Panel (Qty. 2) K- Center Crossbar (Qty. 1) L- Middle Stile (Qty. 2)
M- Bottom Panel (Qty. 1) N- Bottom Back Stretcher (Qty. 1) O- Bottom Front Stretcher (Qty. 1)
P- Bottom Front Molding Q- Upper Back Panel R- Door S- Adjustable Shelf
(Qty. 1) (Qty. 1) (Qty. 2) (Qty. 2)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
T- Stop Rail (Qty. 1) Fireplace Insert (Qty. 1) Remote Control with Battery (Qty. 1)
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel
(Qty. 51+2 extra) (Qty. 51+2 extra) (Qty. 64+2 extra)
(4) Straight Metal Bracket (5) M4 x 38 mm Screw (6) M3 x 15 mm Flat Head Screw
(Qty. 2) (Qty. 12+1 extra) (Qty. 12+1 extra)
(7) M3.5 x 15 mm Washer Head Screw (8) Shelf Support (9) Cam Lock Cover
(Qty. 16+1 extra) (Qty. 8+1 extra) (Qty. 24+1 extra)
(10) Knob (Qty. 2) (11) 25 mm Knob Bolt (Qty. 2) (12) Rubber Bumper (Qty. 4+1 extra)
(13) Triangle Metal Plate (Qty. 2) (14) Floor Leveler (Qty. 2) Glue (Qty. 2)
Touch-up Pen (Qty. 1) Tipping Restraint Hardware Kit (Qty. 2)
(Included in plastic bag)
Tools required: Phillips screwdriver and rubber mallet (not provided).

6
Assembly Instructions
NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled, go back
and fully tighten all bolts. This will make it easier during assembly of unit.
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A), Bottom Panel
(M), Lower Side Panels (F and G) and Upper Front Panels (C) using a Phillips screwdriver.
A
M
F
G
C
C
② x 26

7
Assembly Instructions
3. Securely screw seventeen Cam Bolts (2) into the designated small holes on the Center Shelf (E) on both
sides.
E
E
2
② x 17

8
Assembly Instructions
4. Securely screw the Cam Bolts (2) into the designated small holes on the Lower Partition Panels (H and I)
at both sides.
H
H
I
I
2
② x 8

9
Assembly Instructions
5. Attach the Middle Crossbar (K) to the Center Shelf (E) with two Wood Dowels (3) and three Cam
Locks (1) (Refer to page 3 on Cam Lock system operation supplement).
NOTE: Make sure that you use a small amount of glue with both ends of all dowels.
E
K
3
1
① x 3
③ x 2

10
Assembly Instructions
6. Attach one Front Panel (C) to one Upper Side Panel (B) with one Wood Dowel (3) and two Cam Locks
(1).
7. Repeat the previous step to combine the other Front Panel (C) with the other Upper Side Panel (B)
together.
B
C
3
1
① x 4
③ x 2

11
Assembly Instructions
8. Attach one Middle Stile (L) to the Left Lower Partition Panel (H) with two Wood Dowels (3) and two
Cam Locks (1).
9. Fasten one Lower Back Panel (J) to the Left Lower Partition Panel (H) with three Wood Dowels (3) and
two Cam Locks (1).
10. Repeat the same procedure to attach the other Middle Stile (L) and Back Panel (J) to the Right Lower
Partition (I).
H
J
L
I
L
J
1
3
① x 8
③ x 10

12
Assembly Instructions
11. Attach the Bottom Front Stretcher (O) to the Bottom Front Molding (P) with four Wood Dowels (3) and
eight 38 mm Screws (5).
O
P
5
5
5
5
3
3
3
3
③ x 4
⑤ x 8

13
Assembly Instructions
12. Attach the Bottom Stretchers (N and O) to the Bottom Panel (M) with four Wood Dowel (3) and six
Cam Locks (1).
1
3
M
N
OP
① x 6
③ x 4

14
Assembly Instructions
13. Attach the Left Lower Partition Panel assembly to the Bottom Panel (M) with four Wood Dowels (3)
and two 38 mm Screws (5).
14. Repeat the same procedure to attach the Right Lower Partition Panel assembly at the opposite end.
5
55
5
M
J
H
I
J
③ x 8
⑤ x 4

15
Assembly Instructions
15. Attach the Left Lower Side Panel (F) to the Panels (J, M and N) with six Wood Dowels (3) and three
Cam Locks (1).
16. Repeat the same procedure to attach the Right Lower Side Panel (G) at the opposite end.
1
13
3
H
J
M
N
I
G
J
F
① x 6
③ x 12

16
Assembly Instructions
17. Attach the Center Shelf assembly to the Panels (F, G, H and I) with twelve Wood Dowels (3) and eight
Cam Locks (1).
F
H
I
J
G
J
E
1
3
③ x 12
① x 8

17
Assembly Instructions
18. Attach the Upper Side Panel assemblies to the Center Shelf (E) with four Wood Dowels (3) and four
Cam Locks (1).
19. Fasten the Upper Partition Panel (D) to the Center Shelf (E) with one Wood Dowel (3) and two Cam
Locks (1).
E
B
D
B
1
3
③ x 5
① x 6

18
Assembly Instructions
20. Attach the Top Panel (A) to the Panels (B and D) with five Wood Dowels (3) and six Cam Locks (1).
1
3
B
D
B
A
③ x 5
① x 6

19
Assembly Instructions
21. Using the pilot holes as a guide, fasten two Triangle Metal Plates (13) at the bottom joints between the
Bottom Front Molding (P) and Lower Side Panels (F and G) using four 15 mm Screws (6) per plate.
x 2
6
6
13
F
G
P
M
⑥ x 8

20
Assembly Instructions
22. Tightly screw two Floor Levelers (14) into the Triangle Metal Plates (13) and set to the correct height.
14
14
F
G
P
M
x 2