Superlift RDO-5 Mounting instructions

RDO-5 Roller Door Opener
“Your Automatic Choice”
Installation Instructions and User Guide

CONTENTS
Important Safety Recommendations……………………………...…………………………...1
Installation Instructions........................…………………………………………………..…2 - 3
Settings and Adjustments…………………………………….…………………………..….4 - 6
Technical specifications……………………………………………………………………..…...7
Trouble Shooting Guide………………………………………………………………………7 - 9
No claims whatsoever will be recognized under the terms of this product’s warranty which pertain to
damage, injury, cost or expense, suffered by persons or to property, which either directly or indirectly
arise out of any of the following actions.
a. Failure to install the Opener in accordance with the installation instructions herein contained.
b. The Garage Door striking a moving object.
c. The Opener being used on other than a maximum 4 car residential application.
d. Installing the Opener on an improperly balanced and/or poorly functioning and/or miss aligned Garage
Door.
e. Manually releasing the Garage Door in any position other than when fully closed.
f. Failure to connect the Opener to a properly earthed power supply.
WARRANTY EXCLUSIONS

1
This automatic opener has been designed to provide years of trouble-free use. The opener will
perform efficiently only if it is installed and operated correctly.
FAILURE TO COMPLY WITH THE FOLLOWING SAFETY RECOMMENDATIONS MAY
RESULT IN SERIOUS PERSONAL INJURY, DEATH AND/OR PROPERTY DAMAGE
The installation and adjustment of the Automatic Garage Door Opener (Opener) must be carried out by a technically
qualified or licensed person. It is not recommended that the Opener be installed by a home handyman. Attempting to
install the Opener without suitable technical qualification may result in severe personal injury, death and/or property
damage.
Never install the Opener on a poorly adjusted or worn garage door
The Opener must be installed on a well functioning, properly balanced and aligned garage door. An improperly
balanced or malfunctioning garage door could cause serious injury. Have a qualified person check and if
required, make repairs to the door before installing the Opener. As a rule, a garage door is deemed to be well
balanced and aligned if it; A. requires an equivalent amount of applied force to manually open or close and, B.
requires no more than 150N (15kg) of applied force to either manually open or close and, C. does not rise or fall
more than 100mm when stopped at any position between fully open or fully closed positions and, D. Does not
rub on or make contact with any supporting or surrounding structures.
Repairs to garage doors must only be carried out by technically qualified persons. Attempting to repair the
garage door without suitable technical qualification may result in severe personal injury, death and/or property
damage.
Remove or render inoperative all existing locks and ropes prior to installation of the Opener.
Adjust the disengage cord so that it hangs approximately 1.8 meters from the ground. The instruction tag must
remain attached to the disengage cord.
Do not connect the Opener to the power source until this manual instructs you to do so.
The Opener must be connected to a properly earthed general purpose 220 - 240V power outlet.
Locate the control box; A. within site of the garage door and, B. at a minimum height of 1.5 meters above the
ground so that it remains out of the reach of small children and, C. away from all moving parts of the door.
Affix the entrapment warning label in a prominent location next to the garage door
After installing and adjusting the Opener the door must stop and reverse direction when it comes into contact with
a 40 mm high solid object placed under it on the floor.
The correct function of the safety reversing system should be checked on a monthly basis. Make sure that the
door reverses easily when it makes contact with an obstruction.
Never use the Opener unless the door is in full view and free from objects such as cars, children and/or adults.
Never allow children to use the Opener.
Never use the Opener when children/persons are under or near the path of the door. Children must be supervised
at all times when near the door and when the Opener is in use.
Never attempt to disengage the Opener when there are children/persons or and other objects including motor
vehicles under or near the path of the door.
Attempting to repair the Opener without suitable technical qualification may result in personal injury, death and/or
property/product damage.
Never attempt to make any repairs or remove any screw-on covers from the Opener without first disconnecting the
power supply cord from main power supply.
Always ensure that the garage door is fully open before driving into or out of the garage.
Always ensure the door is fully closed before leaving the driveway.
Adjustments to the safety reverse force settings must be carried out in strict accordance with the procedure set out
in this manual. Failure to do so may result in severe personal injury, death and/or property damage.
Keep hands and loose clothing clear of the door at all times.
For the safety reverse system to function it must first exert force on an object/person/obstruction. As a result the
object/person/door may suffer damage or injury.
The safety reverse system is designed to work on STATIONARY objects only. If the door encounters a moving
IMPORTANT SAFETY RECOMMENDATIONS

2
object during an Open or Close Cycle, serious personal injury, death and/or property/product damage may occur
Right hand installation shown (inside garage looking out) Fig. 1
Check that there is sufficient side clearance to fit the operator unit. It may be fitted to either the
right or left hand side. (fig. 1)
Minimum side clearance:
The minimum side clearance between door
curtain and the inside edge of mounting
bracket is 85mm;
The minimum side clearance between door
curtain and the outside edge of mounting
bracket is 135mm. (fig. 2)
FIXING OF DOOR CURTAIN TO DRUM
WHEEL
The door curtain must be secured to the drum wheel
with suitable fasteners.
With the door in the fully closed position, mark
the curtain at points (A) and (B)
CHECK OPERATION OF THE DOOR
Before beginning the installation of the Opener, check
the operation of the door. The door must be well
balanced and operate smoothly and freely. When
opened to between 900~1200mm from the floor and
released, the door should remain in one fixed position
and not rise or fall. The door should not bind or stick in
the guide tracks. The ideal operational effort, required
to open or close the door, should not exceed a force of
10kg. Superlift does not recommend the
installation of an Automatic Opener to a badly
worn or damaged door.
INSTALLATION INSTRUCTIONS
Fig. 2
Fig. 3

3
Engaging and Disengaging the Opener
Pull manual release lever downwards. (fig. 4)
FIXING OF WEIGHT BARS
Weight bars are generally only required on very light weight
doors. Their main purpose is to eliminate the possibility of
the door curtain “ballooning” on start-up from the fully open
position. If your door “balloons” on initial start-up, after
installing your new opener, we recommend that you fit a
weight bar to the bottom edge of your door.
Move the door manually to the mid open position. Place the
weight bar on the bottom rail of the door and secure with
appropriate fasteners Once the weight bar has been fitted
the door should have a natural tendency to lightly free fall
from the mid open position.
FIXING THE OPENER TO THE DOOR
Slide drive unit onto shaft as shown. (fig. 5)
Ensuring drive lugs engage fully with the narrowest spoke on drum wheel.
N.B.: Right-hand installation shown (inside looking out)
Ensure motor assembly is fully engaged with drum wheel spokes. Clamp shaft to mounting bracket
using “U” Bolts supplied.
Disengage the motor drive by pulling the manual release lever downwards.
Ensure locking bars (if fitted) are removed and keys removed from the lock.
CONTROL BOX
Mount the control box on a smooth flat surface. The area must be completely free of exposure to water,
either direct (rain, garden hose, sprinklers etc.) or indirect (seepage either through or down the internal
face of the wall). The control box contains sensitive electronics which will sustain damage as a result of
any water intrusion. Water damaged electronics are not covered under the terms of the opener
warranty. Important Note: The control box is not waterproof!
Mount control Unit approximately 1.6m from the floor out of the reach of children. Use 4x1” self-
tapping screws and raw plugs. Ensure aerial is clear of all steel supports and coiled electrical leads.
Fit electrical plug from motor unit into bottom of Control Box.
Connect the control unit power cord to an adjacent socket. Ensure that the socket is properly earthed.
INSTALLATION INSTRUCTIONS
Fig. 4

4
Control Box Setup
Remove cover from front of control box.
Operation Controls (fig. 6)
1. SET Button - Confirm set and reversing sensitivity
2. CODE Button - Transmitter code set.
3. UP Button - Limit mode set.
4. DOWN Button - Limit mode set
Circuit Board Connections (fig. 7)
5. Battery Backup connection terminal
6. Motor connection terminal
7. Hall sensor terminal
8. Control board terminal
9. External device connection terminal
SETTINGS AND ADJUSTMENTS
Fig. 6
Fig. 7

5
External Device Terminals Connections. (fig. 8)
1) GND & PB = Push Button terminals. Step by step command input (open, stop, close).
2) 12V & GND & PE = Photo beam terminals.
3) 12V & GND & PB = External receiver terminals
To avoid damaging components while wiring, disconnect the unit from all power.
1. Select Installation Side
Note: The operator is factory set to operate on the right side of the door by default.
To set for left hand side installation, press and hold the SET button until the LED displays 5.
Using the UP or DOWN buttons select 1 for left installation or 0 for right side installation.
Press SET to confirm the setting.
WARNING: This step must be completed prior to setting Open and Close limits and safety
reverse force adjustment if utilizing a lift side installation. If using the standard right-side
installation, this step can be ignored.
2. Setting Open and Close Limits
a. Move the door to the halfway position and engage the opener using the release cord.
b. Press and hold SET button until the LED displays the number 1.
c. Press and hold UP button, the door will travel to the open position, release the button
when the door has reached the desired open position.
d. Fine tune the open position by pressing UP and DOWN buttons.
e. Press SET to store the open position, the LED will display the number 2, it is now
ready to set the close position
f. Press and hold DOWN, the door must travel to the close position, release the button
when the door has reached the desired close position.
g. Fine tune the close position by pressing UP and DOWN buttons.
h. Press SET to store the close position.
The door will then open and close automatically to map the open and close sensitivity force
requirements.
SETTINGS AND ADJUSTMENTS
Fig. 8

6
3. Adjusting Safety Force (Sensitivity)
Force setting range is between 1 –9
a. Press and hold SET until the LED displays number 3. Factory setting is 3.
b. Press UP to increase the force by one degree and DOWN to decrease the force by one
degree. Maximum degree is 9 and the minimum degree is 1.
c. Press SET to store your setting.
4. Photo beam setting (OPTIONAL)
Make sure the photo beams have been installed correctly before setting the Photo beam
function.
a. Press and hold DOWN until the LED displays II.
b. Press the UP button once. The LED displays H. Photo beam function is on. Press the
DOWN button the LED displays II to cancel Photo Beam function.
c. Press SET to store your setting.
5. Setting Auto Close Function
a. Press and hold UP until the LED displays 0.
b. Press UP once, the auto close time will increase by 1 minute, the maximum time is 9
minutes. Press DOWN once, the auto close time will decrease by 1 minute. The LED will
display the current set value.
c. The Auto Close function will be disabled when the setting is 0.
d. Press SET to store your setting.
Note: Auto close is only available when door is at its fully open position. When using
auto close, photo beams must be fitted.
6. Coding and Deleting Transmitters (Maximum 20)
a. Momentarily press CODE button. A Red dot will appear on the display.
b. Press and release a button on the transmitter, the Red dot will disappear, press the
same button a second time, the Red dot will flash and then be replaced by a Uon the
LED display. Transmitter is programmed successfully.
c. Repeat step b. to code a maximum of 20 transmitters.
d. To delete transmitters, press and hold CODE, the LED display dot will flash, keep
holding for approximately 8 seconds until the LED display flashes a C. Release button.
All transmitters are now deleted.
SETTINGS AND ADJUSTMENTS

7
Model
RDO-5
Power Input:
220-240 VAC 50/60Hz
Motor:
18 VAC
Courtesy light time:
3 minutes
Relative humidity:
<90 %
Reception frequency:
433.92 MHz
Transmitter power:
12V Battery
Working temperature:
-20 C –40 C
Open and close force:
600 N
Decoding:
Rolling code
Lamp:
LED, 12V DC
Operator limits travel:
6.5 circles of door drum wheel
Symptom
Possible reason
Solution
The door will not operate from
control box
Power not switch on
Check power is on to control unit(Red
LED illuminated)
Mains plug problem
Plug fully engaged on the control box
and motor wiring connections properly
engaged
“beep, beep.....” from buzzer, and
LED displays ”E2” error code
Motor fault
Push the manual release lever up
Change a new motor
Change a new rotary encoder
TECHNICAL SPECIFICATIONS
TROUBLE SHOOTING GUIDE

8
“beep, beep.....” from buzzer, and
LED displays ”E6” error code
Door twisted
Fix the door
The door does not move, and
LED displays”8” error code
Motor is too hot
Wait for 15 minutes, then restart
The door does not move and LED
displays ”9” when self-learning
after set UP and DOWN limit
Door is too heavy
Improve the weight balance of the door
The door won‟t reverse when
obstructed
The moving force of the
motor is set too high
Decrease the safety reverse force
The door reverses automatically
when closing
The moving force of the
motor is set too low
Increase the safety reverse force
There could be an
obstruction under the door
Remove obstruction
The door stops automatically
when opening
The moving force of the
motor is set too low
Increase the safety reverse force
The operator can be controlled by
O/S/C button but not the remote
The remote light doesn‟t flash
The battery is loose. Open rear cover
and ensure battery is connected.
The receiving antenna is not
pulled out
Pull out the receiving antenna
Low battery in remote
Change new battery(12V)

9
The door can only open, cannot
close
The photocell function was
activated
Close the photocell function
The motor rotates but the door
doesn‟t move
Motor put into manual mode
Push the manual release lever up
The door closes when pressing
„UP‟ during limit setting
Left / right installation error
Chang the installation direction
according to left/right installation setting
in the instruction manual