SuperLightingLED T1 User manual

CCT
DIM
MOD E
POW ER
20S
DEL AY OFF
BRI GHT M ODE
POW ER
● Touch panel single color, dual color, RGB or RGBW PWM constant voltage controller.
● Ultra sensitive high strength glass touch panel with touch color wheel in the middle and backlighting.
● Smooth and accurate color adjustment by touching the color slide.
● Adopt 2.4GHz wireless technology, remote distance up to 30m.
● Touch keys with chord tones and LED indicator.
Wall Mounted Touch Panel
Single Color / Dual Color / RGB / RGBW LED
Constant Voltage Controller
Wiring diagram for PWM output
Feature
User Guide
Technical parameter
Model Input voltage Output current Output power Size(mm)
T1
T2
86x86x35
T3
12-24VDC
12-24VDC
12-24VDC
4CH,3A/CH 144-288W
144-288W
144-288W
4CH,3A/CH
3CH,4A/CH
86x86x35
86x86x35
Output signal
PWM
PWM
PWM
Light type
Single color
Dual color
RGB
T4 12-24VDC 144-288W
4CH,3A/CH 86x86x35
PWM RGBW
Match guide
● T1 Single color panel
Key function
T3
T1
T2
Adjust mode speed,10 levels.
Short press play 10 built-in mode,
long press run mode-cycle.
Adjust brightness, 10 levels.
Play dynamic mode,6 level speed.
Turn on/off light.
Turn on/off light.
Play dynamic mode,6 level speed.
Brightness,10 levels.
Turn off light after 20s.
Color / Brightness wheel
Brightness wheel
Brightness,10 levels.
Color temperature,10 levels.
T4
● Single color panel
● Dual color panel
● RGB panel
● RGBW panel
Use power-up to match the touch panel dimmer with the RF remote (optional).
Note: After touch power key to turn off light, long press power key for 5 seconds will turn on or turn off tone.
Wall mounted single color/dual color/RGB/RGBW LED controller T1/T2/T3/T4 is a full touch controller with
4 channel constant voltage output, and offers fast and accurate color adjustment with unique design touch
color wheel.
SPEED
BRI GHT
MOD E
POW ER
WHI TE
BLU EGRE EN
RED
SCE NE SCE NE SC ENE S CEN E
BRT /SP EEDMOD E
Turn on/off light.
Color slide
Color wheel
Adjust dynamic mode speed
or static color brightness,10 levels.
Red Green Blue White
Short press play 10 built-in mode,
long press run mode-cycle.
4 Scenes,
short press recall scene.
Long press to save the
current color into 1/2/3/4.
1. Match: Switch off the power, then switch on power again,
short press on/off key or zone key 3 times on the RF remote quickly within 5s after power on,
the link is done once the light blinks 3 times.
2. Delete: Switch off the power, then switch on power again,
short press on/off key or zone key 5 times on the RF remote quickly within 5s after power on,
the unlink is done once the light blinks 5 times.
3. Multiple zone remote only use zone key to match each zone receiver.
Power Supply
12-24VDC
Constant Voltage
AC110-230V
+ + + +
Single color LED strip x 4

Malfunctions analysis & troubleshooting
Wrong color 1. Wrong connection of R/G/B/W wires. 1. Reconnect R/G/B/W wires.
Malfunctions
Causes Troubleshooting
Uneven intensity
between front and
rear,with voltage drop
1. Output cable is too long.
2. Wire diameter is too small.
3. Overload beyond power supply capability.
4. Overload beyond controller capability.
1. Reduce cable or loop supply.
2. Change wider wire.
3. Replace higher power supply.
4. Add power repeater.
1. No power.
2. Wrong connection or insecure.
1. Check the power.
2. Check the connection.
No light
1. The product shall be installed and serviced by a qualified person.
2. The product is non-waterproof. Please avoid the sun and rain.
3. Good heat dissipation will prolong the working life of the controller, Please ensure good ventilation.
4. Please check if the output voltage of any power supplies used comply with the working voltage
of the product.
5. Ensure all wire connections and polarities are correct and secure before applying power to avoid
any damages to the LED lights.
6. If a fault occurs please return the product to your supplier. Do not attempt to fix this product by yourself.
Safety information
LED power supply voltage and power select :
● 12V lamp, Input 12V power supply, can load 0~144W,
● 24V lamp, Input 24V power supply, can load 0~288W,
The power supply power must larger than load power 20%.
● T4 RGBW panel
Dimension
RGBW LED strip
W
Power Supply
12-24VDC
Constant Voltage
AC110-230V
Installation diagram
Typical base as below:
European style 86 size
Uninstall Touch panel Baseplate Base
● T2 Dual color panel
Dual color LED strip x 2
● T3 RGB panel
+
CW WW
+
CW WW
Power Supply
12-24VDC
Constant Voltage
AC110-230V
Power Supply
12-24VDC
Constant Voltage
AC110-230V
RGB LED strip