Supermicro SC825TQC-R1K03WB User manual

USER’S MANUAL
Revision 2.0d
SC825 ChASSiS SERiES
SC825TQC-R1K03WB
SC825TQC-R740WB SC825TQC-R1K03LPB
SC825TQ-R740WB SC825TQC-R740LPB
SC825TQ-R740LPB SC825TQ-R740UB
SC825TQ-R720LPB SC825TQ-710LP
SC825TQ-R720UB SC825TQ-R700LP(V)(B)
SC825TQ-R700U(V)(B) SC825TQC-600LPB
SC825TQ-600LPB SC825TQC-600WB
SC835TQ-600WB SC825TQ-563UB
SC825TQ-560LP(V)(B) SC825TQ-563LPB
SC825TQ-R500WB SC825TQ-560U(V)(B)

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 2.0d
Release Date: January 12, 2018 mk
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2018 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

3
Preface
Preface
About this Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the chassis. Installation and
maintenance should be performed by experienced technicians only.
This document lists compatible parts available when this document was published.
Refer to the Supermicro web site for updates on supported parts and congurations.
This manual may be periodically updated without notice. Please check the
Supermicro Web site for possible updates.
Warnings
Special attention should be given to the following symbols used in this manual.
Warning! Indicates high voltage may be encountered when performing
a procedure.
Warning! Indicates important information given to prevent equipment/
property damage or personal injury.

4
SC825 Chassis Manual
Contents
Contacting Supermicro ................................................................................................. 7
Chapter 1 Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Shipping List.................................................................................................... 1-1
1-3 Chassis Features ............................................................................................ 1-2
CPU................................................................................................................. 1-2
Hard Drives ..................................................................................................... 1-2
I/O Expansion slots......................................................................................... 1-2
Peripheral Drives............................................................................................. 1-2
Other Features................................................................................................ 1-2
1-5 Returning Merchandise for Service................................................................. 1-3
Chapter 2 Standardized Warning Statements for AC Systems
About Standardized Warning Statements....................................................... 2-1
Warning Denition........................................................................................... 2-1
Installation Instructions.................................................................................... 2-4
Circuit Breaker ................................................................................................ 2-5
Power Disconnection Warning ........................................................................ 2-6
Equipment Installation..................................................................................... 2-8
Restricted Area................................................................................................ 2-9
Battery Handling............................................................................................ 2-10
Redundant Power Supplies ......................................................................... 2-12
Backplane Voltage ........................................................................................ 2-13
Comply with Local and National Electrical Codes........................................ 2-14
Product Disposal........................................................................................... 2-15
Hot Swap Fan Warning................................................................................. 2-16
Power Cable and AC Adapter ...................................................................... 2-18
Chapter 3 Chassis Components
3-1 Overview ......................................................................................................... 3-1
3-2 Components.................................................................................................... 3-1
Chassis............................................................................................................ 3-1
Backplane........................................................................................................ 3-1
Fans ................................................................................................................ 3-1
Mounting Rails ................................................................................................ 3-1
Power Supply.................................................................................................. 3-2
Air Shroud ....................................................................................................... 3-2
3-3 Where to get Replacement Components........................................................ 3-2

5
Preface
Chapter 4 System Interface......................................................................4-1
4-1 Overview ......................................................................................................... 4-1
4-2 Control Panel Buttons ..................................................................................... 4-2
4-3 Control Panel LEDs ........................................................................................ 4-2
4-4 Drive Carrier LEDs.......................................................................................... 4-4
SAS/SATA Drives ............................................................................................ 4-4
Chapter 5 Chassis Setup and Maintenance
5-1 Overview ......................................................................................................... 5-1
5-2 Installation and General Maintenance ............................................................ 5-1
Installation ....................................................................................................... 5-1
5-3 Removing the Chassis Cover ......................................................................... 5-2
5-4 Installing Hard Drives...................................................................................... 5-3
5-6 DVD-ROM Replacement or Installation .......................................................... 5-7
Replacing the DVD-ROM and Front Panel..................................................... 5-8
5-7 Installing the Motherboard .............................................................................. 5-8
I/O Shield ........................................................................................................ 5-8
Installing the I/O Shield................................................................................... 5-9
Permanent and Optional Standoffs................................................................. 5-9
PCI Slot Setup ...............................................................................................5-11
PCI Slot Setup for SC829TQ-R920UB (Universal Output)........................... 5-12
PCI/PCIE Slot Setup for SC829BTQ-R920WB (Wide I/O)........................... 5-13
5-8 Installing the Air Shroud................................................................................ 5-15
Checking the Server's Airow ....................................................................... 5-16
Installation Complete..................................................................................... 5-16
5-9 System Fans ................................................................................................. 5-17
5-10 Power Supply ............................................................................................... 5-19
Power Supply Failure.................................................................................... 5-19
5-11 Replacing the Power Distributor ................................................................... 5-21
5-12 Replacing or Installing the Front Port Panel................................................. 5-22
5-13 Optional Front Bezel ..................................................................................... 5-23
Chapter 6 Chassis Installation
6-1 Unpacking the System .................................................................................... 6-1
6-2 Preparing for Setup......................................................................................... 6-1
Choosing a Setup Location............................................................................. 6-1
6-3 Warnings and Precautions .............................................................................. 6-2
Rack Precautions............................................................................................ 6-2
Server Precautions.......................................................................................... 6-2
Rack Mounting Considerations ....................................................................... 6-3

6
SC825 Chassis Manual
6-4 Installing the System into a Rack ................................................................. 6-4
Identifying the Sections of the Rack Rails...................................................... 6-4
Releasing the Inner Rail ................................................................................. 6-5
Installing the Inner Rails on the Chassis ........................................................ 6-6
Installing the Outer Rails onto the Rack......................................................... 6-7
Sliding the Chassis onto the Rack Rails......................................................... 6-8
Appendix A SC829 Chassis Cables
Appendix B SC829 Power Supply Specications
Appendix C SAS-825TQ Backplane Specications

7
Preface
Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Web Site: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [email protected]
Web Site: www.supermicro.com.tw

8
SC825 Chassis Manual
Notes

Chapter 1
Introduction
1-1 Overview
Supermicro’s SC825 2U chassis features a unique and highly-optimized design.
The chassis is equipped with high efciency power supply.
1-2 Shipping List
Please visit the following link for the latest shipping lists and part numbers for your
particular chassis model www.supermicro.com
Chapter 1: Introduction
1-1
SC825 Chassis
Model HDD PCI Slots Power Supply
SC825TQC-R1K03LPB 8x SAS3 / SATA 7x LP
1000W
(Titanium Level
Redundant)
SC825TQC-R1K03WB 8x SAS3 / SATA 4x FH + 3x LP
1000W
(Titanium Level
Redundant)
SC825TQ-R740WB 8x SAS / SATA 4x FH 3x LP 740W (Platinum Level
Redundant)
SC825TQ-R740UB 8x SAS / SATA 4x FH + 3x LP 740W (Platinum Level
Redundant)
SC825TQC-R740WB 8x SAS3 / SATA 4x FH + 3x LP 740W (Platinum Level
Redundant)
SC825TQC-R740LPB 8x SAS3 / SATA 7x LP 740W (Platinum Level
Redundant)
SC825TQ-R740LPB 8x SAS / SATA 7x LP 740W (Platinum Level
Redundant)
SC825TQ-720LPB 8x SAS/SATA 7x LP 720W (Gold Level)
SC825TQ-720UB 8x SAS / SATA 4x FH + 3x LP 720W (Gold Level)
SC825TQ-710LPB 8x SAS / SATA 7x LP 710W
SC825TQ-R700UV/
SC825TQ-R700UB 8x SAS / SATA 4x FH + 3x LP 700W Redundant
Legend: FF: Full-height, full length, FH: Full-height, half length. LF: Low-prole,
full-length. LP: Low-prole.

SC825 Chassis Manual
1-2
SC825 Chassis
SC825TQ-R700LPV/
SC825TQ-R700LPB 8x SAS/SATA 7x LP 700W (Redundant)
SC825TQC-600LPB 8x SAS3/SATA 7x LP 600W (Platinum Level)
SC825TQC-600WB 8x SAS3/SATA 4x FH + 3x LP 600W (Platinum Level)
SC825TQ-600WB 8x SAS/SATA 4x FH + 3x LP 600W (Platinum Level)
SC825TQ-600LPB 8x SAS/SATA 7x LP 600W
SC825TQ-563LPB 8x SAS/SATA 7x LP 560W
SC825TQ-563UB 8x SAS/SATA 4x FH + 3x LP 560W
SC825TQ-560UV /
SC825TQ-560UB 8x SAS/SATA 4x FH 3x LP 560W
SC825TQ-560LPV /
SC825TQ-560LPB 8x SAS/SATA 7x LP 560W
SC825TQ-R500WB 8x SAS/SATA 4x FF 3x LP 500W (Platinum Level
Redundant)
Legend: FF: Full-height, full length, FH: Full-height, half length. LF: Low-prole,
full-length. LP: Low-prole.

1-3
Chapter 1: Introduction
1-3 Chassis Features
The SC825 2U, high-performance chassis includes the following features:
Hard Drives
The SC825 chassis features eight slots for SAS3 and SAS/SATA drives. These
drives are hot-swappable. Once set up correctly, these drives can be removed with-
out powering down the server. In addition, these drives support SES2 (SAS/SATA).
PCI Expansion slots
Each SC825 chassis model includes seven low-prole I/O expansion slots.
Peripheral Drives
Each SC825 chassis supports one slim DVD-ROM drive (included) and one slim
oppy drive (optional). These drives allow you to quickly install or save data.
Other Features
Other onboard features are included to promote system health. These include
various three cooling fans, a convenient power switch, reset button, and ve LED
indicators.

SC825 Chassis Manual
1-4
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Website: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [email protected]
Website: www.supermicro.com.tw

1-5
Chapter 1: Introduction
1-5 Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required be-
fore any warranty service will be rendered. You can obtain service by calling your
vendor for a Returned Merchandise Authorization (RMA) number. When returning to
the manufacturer, the RMA number should be prominently displayed on the outside
of the shipping carton, and mailed prepaid or hand-carried. Shipping and handling
charges will be applied for all orders that must be mailed when service is complete.
For faster service, RMA authorizations may be requested online (http://www.
supermicro.com/support/rma/).
Whenever possible, repack the chassis in the original Supermicro carton, using the
original packaging material. If these are no longer available, be sure to pack the
chassis securely, using packaging material to surround the chassis so that it does
not shift within the carton and become damaged during shipping.
This warranty only covers normal consumer use and does not cover damages in-
curred in shipping or from failure due to the alteration, misuse, abuse or improper
maintenance of products.
During the warranty period, contact your distributor rst for any product problems.

SC825 Chassis Manual
1-6
Notes

2-1
Chapter 2: Warning Statements for AC Systems
Chapter 2
Standardized Warning Statements for AC Systems
About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certied technicians should attempt to install or congure
components.
Read this appendix in its entirety before installing or conguring components in the
Supermicro chassis.
These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.
Warning!
This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
Warning Denition
警告の定義
この警告サインは危険を意 味します。
人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、
電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。
此警告符号代表危险。
您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分
意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。
此警告符號代表危險。
您目前所處的工作環境可能讓您受傷。您使用任何設備之前，請注意觸電的危險，
並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號碼找到相關
的翻譯說明內容。

2-2
SC825 Chassis Manual
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie benden sich in einer Situation, die zu
Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes
de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
nal de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES.
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
gurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la n de chaque avertissement.
CONSERVEZ CES INFORMATIONS.
ןונקת תורהצהאהרהז
ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח
ה וא תולאש שיו הדימב .תירשפא תיזיפי ,יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק
רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תאה .םיביכר
אורקל שי .ורקימרפוס יזראמב םיביכרה תרדגה וא תנקתה ינפל ואולמב חפסנה תא

2-3
Chapter 2: Warning Statements for AC Systems
2-3
안전을 위한 주의사항
경고!
이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준
작업절차를 준수해 주시기 바랍니다.
해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.
BEWAAR DEZE INSTRUCTIES
.   !





2-4
SC825 Chassis Manual
Installation Instructions
Warning!
Read the installation instructions before connecting the system to the power source.
Warnung
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen
lesen.
¡Advertencia!
Lea las instrucciones de instalación antes de conectar el sistema a la red de
alimentación.
Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives
d'installation.
設置手順書
システムを電源に接続する前に、設置手順書をお読み下さい。

אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.
시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.
Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron
aansluit.
警告
将此系统连接电源前,请先阅读安装说明。
警告
將系統與電源連接前，請先閱讀安裝說明。

2-5
Chapter 2: Warning Statements for AC Systems
Circuit Breaker
Warning!
This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.
サーキット・ブレーカー
この製品は、短絡（過電流）保護装置がある建物での設置を前提としています。
保護装置の定格が250 V、20 Aを超えないことを確認下さい。
Warnung
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss-
bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.
¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)
del edicio. Asegúrese de que el dispositivo de protección no sea superior a: 250
V, 20 A.
Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit
dépend de l'installation électrique du local. Vériez que le courant nominal du
dispositif de protection n'est pas supérieur à :250 V, 20 A.
לע ךמתסמ הז רצומנגהה תעינמל םינבמב תנקתומה יכ אדוול שי .ילמשח רצק
רצקה ינפמ ןגמה רישכמה ילמשחהמ רתוי אל אוה-250 V, 20 A


20A, 250V: 
警告
此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电
流不大于250V,20A。
警告
此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電
流不大於250V,20A。

2-6
SC825 Chassis Manual
Power Disconnection Warning
電源切断の警告
システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス
するには、
システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り
外す必要があります。
警告
在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。
警告
在您打開機殼安裝或移除內部元件前，必須將系統完全斷電，並移除電源線。
Warnung
Das System muss von allen Quellen der Energie und vom Netzanschlusskabel
getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es
Warning!
The system must be disconnected from all sources of power and the power cord
removed from the power supply module(s) before accessing the chassis interior to
install or remove system components.
경고!
이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에
의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지
않도록 해야 합니다.
Waarschuwing
Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van
uw electrische installatie. Controleer of het beveiligde aparaat niet groter
gedimensioneerd is dan 220V, 20A.