Supermicro X11SSW-F User manual

SUPERMICR R
CONTACT INFORMATION
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com/CDR_Images/CDR-X11-UP/
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
© 2015 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Supermicro's written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.
PACKAGE CONTENTS
X11SSW-F
QUICK REFERENCE GUIDE 1.00
• One (1) Supermicro Motherboard
• Six (6) SATA Cables
• One (1) I/O Shield
• One (1) Quick Reference Guide
• Website: www.supermicro.com
• General Information: [email protected]
• Technical Support: [email protected]
• Phone: [phone], Fax: [phone]
FOR YOUR SYSTEM TO WORK PROPERLY, PLEASE DOWNLOAD APPROPRIATE
DRIVERS/IMAGES/USER'SMANUAL FROM THE LINKS BELOW:
MNL-1784-QRG REV. 1.00
Connectors DIMM Memory Installation
Jumpers and Connectors
Back Panel I/O Connectors
Memory Support
Motherboard Layout and Features Jumpers
CPU Installation
Note: Refer to Chapter 1 of the User Manual for detailed information on jumpers, connectors,
and LED indicators. Note: Refer to Chapter 2 of the User Manual for detailed information on memory support and CPU/
motherboard installation instructions.
= mounting hole
Heatsink Installation Front Panel Control (JF1)
LED Indicators
BJC E
F
G
LED Indicators
Jumper Description Default
JBR1 BIOS Recovery Pins 1-2 (Normal)
JBT1 Clear CMOS See Chpt. 2 in User Manual
JI2C1/JI2C2 SMB to PCI Slots Pins 2-3 (Disabled)
JPB1 BMC Enable/Disable Pins 1-2 (Enabled)
JPG1 VGAEnable Pins 1-2 (Enabled)
JPL1/JPL2 LAN1/LAN2 Enable Pins 1-2 (Enabled)
JPME2 Manufacturing Mode Select Pins 1-2 (Normal)
JWD1 Watch Dog Enable Pins 1-2 (Reset)
Connector Description
BT1 Onboard Battery
COM1/COM2 COM1/COM2 Port Headers
Fan1-Fan6 System/CPU Fan Headers
IPMI_LAN IPMI_Dedicated Gigabit (RJ45) Port
I-SATA2-I-SATA7 SATA3.0 Connectors via Intel PCH (6Gb/s)
I-SGPIO 1/2 Serial_Link General Purpose I/O Connection Headers for I-SATA3.0 connections
(I-SGPIO1 for I-SATA2-3, I-SGPIO2 for I-SATA4-7)
J23 M.2 Socket 3 (supports 2260, 2280, 22110 for NVMe and SATASSD)
JD1 Speaker/Power LED Indicator
JF1 Front Panel Control Header
JIPMB1 4-pin External BMC I2C Header (for an IPMI Card)
JL1 Chassis Intrusion Header
JOH1 Overheat LED Indicator
JPI2C1 Power I2C System Management Bus (Power SMB) Header
JPWR1 24-pin ATX Main Power Connector (Required)
JPWR2 +12V 8-pin CPU Power Connector (Required)
JSD1/JSD2 SATADisk On Module (DOM) Power Connectors
JSTBY1 Standby Power Header
JSXB1A/1B/1C SMC-Proprietary WIO_L (Left)Add-On Card Slot
JSXB2 SMC-Proprietary WIO_R (Right)Add-On Card Slot
JTPM1 Trusted Platform Module (TPM)/Port 80 Connector
JUIDB1 UID (Unit Identification) Switch
LAN1/LAN2 Gigabit (RJ45) LAN Ports
SP1 Internal Speaker/Buzzer
USB 0/1 Back Panel USB 2.0 Ports
USB 2/3 USB 2.0 Header
USB 4/5 USB 2.0 Header
USB 6/7 Back Panel USB 3.0 Ports
USB 8 USB 3.0 Type-A Header
USB 9/10 Front Panel Accessible USB 3.0 Header
VGA Back Panel VGA Port
Power Button
1
NIC1 Link LED
Reset Button
2
HDD LED
FP PWRLED
Reset
PWR
3.3 V
ID_UID_SW/3.3V Stdby
Ground
Ground
19 20
Power Fail LED
NIC2 Link LED
NIC2 Active LED
NIC1 Active LED
X
X
NMI Ground
Red+ (Blue LED Cathode) Blue+ (OH/Fan Fail/UID LED)
3.3V
LED Description Color/State Status
LE1 Rear UID LED Blue: On Unit Identified
LEDBMC BMC Heartbeat LED Green: Blinking BMC Normal
LEDEC1 EC Heartbeat LED Green: Blinking EC Normal
LEDPWR System Standby Power LED Green: Solid On Power On
I/O Back Panel
A. COM 1 D. IPMI LAN G. LAN1 J. UID Switch
B. USB Port 0 (2.0) E. USB Port 6 (3.0) H. LAN2
C. USB Port 1 (2.0) F. USB Port 7 (3.0) I. VGA
A
D
I
H
Memory Population Guidelines
Please follow the table below when populating the X11SSW-F:
Insert the desired number of DIMMs into the memory slots. The DIMM slots
should be populated in the following order: DIMMB2, DIMMA2, DIMMB1,
DIMMA1. For the system to work properly, please use memory modules of the
same type and speed in the motherboard.
Channel A Slot 1
Channel A Slot 2
(Blue Slot)
Channel B Slot 1
Channel B Slot 2
(Blue Slot)
Towards the CPU
Notches
Release Tabs
Press both notches
straight down into
the memory slot.
Memory Module Population
DIMM Slots
per Channel DIMM Type POR Speeds (MHz) Ranks per DIMM Layer Count FW Base Supported Voltage
2Unbuffered
DDR4 ECC 2133, 1866, 1600, 1333 SR, DR 6 SPS 1.2V
The X11SSW-F has four (4) 288-pin DIMM slots that support up to 64GB of SDRAM
72-bit DDR4 unbuffered ECC 2133/1866/1600/1333MHz memory.
Turn Clockwise
to Lock
Thermal Paste
P ush Down
Turn Counter-
clockwise to
Unlock Connect the Heatsink Wire to
the CPU Fan Connector
CPU Properly
Installed
Load Lever Locked
into Place
Load Lever
Load Plate
Pin 1
North Center Edge
LAN2 LAN1 USB0/1
USB6/7
(3.0)
VGA
SP1
CPU
BIOS
LICENSE
MAC CODE
BAR CODE
IPMI CODE
IPMI_L
COM1
BT1
COM2 USB2/3 USB8(3.0)
J23
USB4/5 USB9/10(3.0)
JTPM1
JPWR1
JOH1
JPI2C1
LEDPWR
JD1
JPWR2
FAN1
FAN2
FAN3
FAN4
FAN5
FAN6
JF1
I-SGPIO2
I-SGPIO1
JL1
I-SATA3
I-SATA2
JSD1 JSD2
JSXB1C
JSXB1B
JSXB2
JSXB1A
JI2C1
JI2C2
JWD1 JPL2
JPG1
JPB1
JPME2
JBR1
LE1
JBT1
LEDEC1
LEDBMC
JPL1
I-SATA7
I-SATA6 I-SATA4
I-SATA5
SRW2
SRW3
SRW1
SRW4
BMC
X11SSW-F
REV:1.01
Designed in the USA
JIPMB1
JSTBY1
DIMMA1
DIMMA2
DIMMB1
DIMMB2
2260
2280
22110
JUIDB1
Intel PCH