Supero SC822R User manual

1.0a
®
SUPER
SC822 CHASSIS
USER'S GUIDE
(SC822T/SC822S/SC822R)
(SC822i)

1-2
SC822 Chassis User’s Guide
The information in this User’s Guide has been carefully reviewed and is believed to be
accurate. The vendor assumes no responsibility for any inaccuracies that may be
contained in this document, makes no commitment to update or to keep current the
information in this manual, or to notify any person or organization of the updates. Please
Note: For the most up-to-date version of this manual, please see our
web site at www.supermicro.com.
SUPERMICRO COMPUTER reserves the right to make changes to the product described in
this manual at any time and without notice. This product, including software, if any, and
documentation may not, in whole or in part, be copied, photocopied, reproduced, translated
or reduced to any medium or machine without prior written consent.
IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR
INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE
LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE
PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of
Santa Clara shall be the exclusive venue for the resolution of any such disputes.
Supermicro's total liability for all claims will not exceed the price paid for the hardware
product.
Unless you request and receive written permission from SUPER MICRO COMPUTER, you
may not copy any part of this document.
Information in this document is subject to change without notice. Other products and
companies referred to herein are trademarks or registered trademarks of their respective
companies or mark holders.
Copyright © 2004 by SUPER MICRO COMPUTER INC.
All rights reserved.
Printed in the United States of America

1-3
Chapter 1: Safety Information and Technical Specifications
Table of Contents
Chapter I: Safety Information and Technical Specifications.......... 1-4
1-1. Electrical Safety Guidelines ............................................................. 1-4
1-2. General Safety Guidelines............................................................... 1-5
1-3. ESD Safety Guidelines ....................................................................... 1-6
1-4. Operation Safety Guidelines.......................................................... 1-6
1-5. Product Compliance Information................................................. 1-8
1-6. Packing List and the SC822 Specifications ............................ 1-9
Chapter 2: Chassis Description and Installation Procedures........ 2-1
2-1. Chassis Description ........................................................................... 2-1
A. Contents of the Accessory Kit ............................................................... 2-1
B. Chassis Front View and the Front Control Panel ................................ 2-2
C. Chassis Rear View and the Back Panel .............................................. 2-4
2-2. Chassis Installation ........................................................................... 2-6
A. Important Safety Guidelines ..................................................................... 2-6
B. Tools Needed.............................................................................................. 2-6
C. Removing the Top Cover of the Chassis............................................... 2-7
D1. Accessing the SCA/SATA Drive Tray and Installing a Hard Disk .. 2-8
D2. Accessing the IDE Drive Tray and Installing a Hard Disk ................ 2-9
E. Accessing the Front Chassis Fans ...................................................... 2-10
F. Accessing the Redundant Power Supply............................................ 2-11
G. Installing the Motherboard ...................................................................... 2-12
H. Installing Chassis Rails........................................................................... 2-13
I. Rack Installation........................................................................................ 2-15

1-4
SC822 Chassis User’s Guide
Chapter 1-Safety Information and Technical
Specifications
1-1 Electrical Safety Guidelines
Warning: To avoid electrical shock, check the power
cords as follows:
Checking the Power Cords
!Use the exact type of power cords as required.
!Be sure to use power cord(s) that came with safety certifications.
!The power cord(s) must be compliant with the AC voltage requirements in your
region.
!The power cord plug cap must have an electrical current rating that is at least
125% of the electrical current rating of this product.
!The power cord plug cap that plugs into the AC receptacle on the power
supply must be an IEC 320, sheet C13, type female connector.
!Be sure to disconnect the power supply before accessing the SC822 or its
components.
!Plug the Power cord(s) into a socket that is properly grounded before
turning on the power.
Warning: Follow the guidelines below to avoid possible
damages to the system or injury to yourself:
General Electrical Safety Guidelines
!Be aware of the locations of the power switches on the chassis and in the
room, so you can disconnect the power supply if an accident occurs.
!Take extra precautionary measures when working with high voltage
components. It is not recommended to work alone.
!Before removing or installing main system components, be sure to
disconnect the power first. Turn off the system before you disconnect
the PS.
Use only one hand when working with powered-on electrical equipment to
avoid possible electrical shock.

1-5
Chapter 1: Safety Information and Technical Specifications
Use rubber mats specifically designed as electrical insulators when working
with computer systems.
The power supply or power cord must include a grounding plug and must
be plugged into grounded outlets.
Motherboard Battery: CAUTION -Make sure not to install the onboard battery
upside down to avoid possible explosion. Make sure that the positive side
should be facing up on the motherboard. This battery must be replaced
only with the same or an equivalent type recommended by the manufac-
turer. Dispose of used batteries according to the manufacturer's instruc-
tions.
CD-ROM Laser: CAUTION - Do not open the enclosures of power supplies
or CD ROM to avoid injury.
1-2 General Safety Guidelines
Warning: Follow these rules to ensure general safety:
Keep the area around the SC822 clean and free of clutter.
To avoid injuries to the back, be sure to use your leg muscles, keep your
back straight, and bend your knees, when lifting the system.
Avoid wearing loose clothing to preventing it from coming into contact with
After removing the components or chassis covers from the system, place
them on a table for safeguard.
Be sure to remove any jewelry or metal objects before working on the
chassis to avoid short circuits should these objects come into contact
with power circuits.
After accessing the interior of the chassis, be sure to close the chassis
with chassis covers and secure the chassis to the racks with screws.

1-6
SC822 Chassis User’s Guide
1-3 ESD Safety Guidelines
Use a grounded wrist strap designed to prevent static discharge.
Keep all components and printed circuit boards (PCBs) in their antistatic
bags until ready for use.
Touch a grounded metal object before removing the board from the antistatic bag.
Do not let components or PCBs come into contact with your clothing, which may
retain a charge even if you are wearing a wrist strap.
Touch a grounded metal object before removing the board from the antistatic
bag.
Handle a board by its edges only; do not touch its components, peripheral
chips, memory modules or contacts.
When handling chips or modules, avoid touching their pins.
Put the motherboard and peripherals back into their antistatic bags when not in
use.
For grounding purposes, make sure your computer chassis provides excel-
lent conductivity between the power supply, the case, the mounting
fasteners and the motherboard.
Electric Static Discharge (ESD) can damage electronic com-
ponents. To prevent damage to your system board, it is
important to handle it very carefully. The following measures are
generally sufficient to protect your equipment from ESD.
1-4 Operation Safety Guidelines
Warning: For proper cooling, make sure to install all
chassis covers before turning on the system. If this rule is
not strictly followed, warranty may become void. Do not open
the casing of a power supply. Power supplies can only be
accessed and serviced by a qualified technician of the manufacturer.

1-7
Chapter 1: Safety Information and Technical Specifications
To avoid personal injury and property damage, please carefully
follow all the safety steps listed below:
Before accessing the chassis:
1. Turn off all peripheral devices connected to the SC822.
2. Press the power button to power off the system.
3. Unplug all power cords from the system or the wall outlets.
4. Disconnect all the cables and label the cables for easy identification.
5. Use a grounded wrist strap designed to prevent static discharge when
handling components.
Removing the chassis covers:
After completing the above steps, you can remove the covers and install
components/peripheral devices into the chassis as described in Chapter 2.
1. Unlock and remove the screws and fasteners to remove the cover or
components.
2. Save all the screws and fasteners for later use. (If necessary, label these
screws or fasteners for easy identification.)
3. Follow the instruction given in Chapter 3 to remove the chassis covers.
Reinstalling the chassis covers:
To maintain proper system cooling and airflow, do not operate the system
without installing all chassis covers back to the chassis. To reinstall the chassis
covers, please follow the steps listed below:
1. Make sure that all components and devices are securely fastened
on the chassis and there are no loose parts/screws inside the chassis.
2. Make sure that all cables are properly connected to the connectors and ports.
3. Use the original screws or fasteners to install the covers to the chassis.
4. Be sure to lock to the chassis or the system to prevent unauthorized access.
5. For proper cooling, enclose the chassis with covers before operating the
system.

1-8
SC822 Chassis User’s Guide
Before installing the chassis into a rack:
1. Make sure that the rack is securely anchored onto a unmovable surface or
structure before installing the chassis into the rack.
2. Unplug the power cord(s) of the rack before installing the chassis into the
rack.
3. Make sure that the system is adequately supported. Make sure that all the
components are securely fastened to the chassis toprevent components fall-
ing off from the chassis.
4. Be sure to install an AC Power Disconnect for the entire rack assembly and
this Power Disconnect must be clearly marked.
5. The rack assembly shall be properly grounded to avoid electric shock.
6. The rack assembly must provide sufficient airflow to the chassis for proper
cooling.
1-5 Product Compliance Information
The SC822 CHASSIS is compliant with the following safety standards/
requirements:
Product Safety
*Canada/USA--UL60 950-CSA60 950
*European Union--EN 60 950
*International--IEC60 950
Electromagnetic Compatibility (EMC)-Emissions
*European Union--EN55022: 1994
*International--CISPR22
*USA--Title 47 CFR, Part 15
Power Line Harmonics/Voltage Flicker
*European Union--EN61000-3-2/EN61000-3-3
*International--IEC61000-3-2
Electromagnetic Compatibility-Immunity
*European Union--EN55024: 1998
*International--CISPR24

1-9
Chapter 1: Safety Information and Technical Specifications
A. The SC822 Series chassis contains the following:
1-6 Packing List and the SC822 Specifications
!One (1) 1.44" floppy drive
!One (1) slim CD-ROM drive (*For the SC822R, SC822T-R only)
!One (1) 5.25" drive bay
!One (1) I/O shield
!SCSI Accessories (*For the SC822R, SC822S only)
One (1) SCSI backplane
One (1) SCSI Ultra 320 Cable
Six (6) SCSI drive carriers
!SATA Accessories (*For the SC822T only)
One (1) SATA backplane
One (1) SATA Activity LED cable
Six (6) SATA cables
Six (6) SATA drive carriers
!IDE Accessories (*For the SC822i only)
Two (2) IDE drive carriers
One (1) IDE cable
B. SC822 Specifications
For the SC822-IDE Models-(*822i-300LP/822i-400RC)
SC822-IDE-(*822i-300LP/822i-400RC)
Component Part# Qty Notes
IDE Drive Tray CSE-PT18 (B) 2
8 cm Hot -Swap Chassis Fan Fan-044 4
300W Power Supply PWS-028 1 (*for 822i -300LP)
400W Power Supply PWS-027 1 (*for 822i -400RC)
Floppy Drive FPD-PNSC-02(01) 1
Riser Card CSE-RR2U-50 1 (*for 822i -400RC)
Rackmount Hardware CSE-PT 25 1

1-10
SC822 Chassis User’s Guide
C. SC822 Power Supply Specifications
      
      
      
       
      
      
     
      
      

      
      
      
      
      
      
For the SC822-SCSI Models-(*822S-400LP/822R-400RC/822R-350RC/822R-
400LP)
For the SC822-SATA Models-(*822T-550LP/822T-R500RC)
SC822-SCSI-(*822S-400LP/822R-400RC/822R-350RC/822R-400LP)
Component Part# Qty Notes
SCA Drive Tray CSE-PT17 (B) 6
8 cm Hot -Swap Chassis Fan Fan-044 4
350W Power Supply PWS-030 2 (*for 822R-350RC)
400W Power Supply PWS-027 1 (* for 822S-400LP)
400W Power Supply PWS-037 2 (* for 822R-400RC
822R-400LP)
6-port SCSI Backplane CSE-SCA-822 1
SCSI Cable CBL-033-U320 1
Floppy Drive FPD-PNSC-02(01) 1
CD ROM CDM-TEAC-024(B) 1 (*for Redundant Chassis)
Riser Card CSE-RR2U-50 1 (*for Chassis w/Riser Cards)
Rackmount Hardware CSE-PT-25 1
SC822-SATA-(*822T-550LP/822T-R500RC)
Component Part# Qty Notes
SCA Drive Tray CSE-PT17 (B) 6
8 cm Hot -Swap Chassis Fan Fan-044 4
500W Power Supply PWS-0049 2 (*for 822T-R500RC)
550W Power Supply PWS-0047 1 (* for 822T-550LP)
6-port SATA Backplane CSE-SATA-822 1
SATA Cable CBL-0044 6
SATA Activity LED Cable CBL-0077 1
Floppy Drive FPD-PNSC-02(01) 1
CD ROM CDM-TEAC-024(B) 1 (*for 822T-R500RC)
Riser Card CSE-RR2U-50 1
(*for 822T-R500RC)
Rackmount Hardware CSE-PT-25 1