Supero SC813 Series User manual

Rev. 1.0b
®
SUPER
The SC813/SC813M Chassis Series
InstallationGuide

SC813/813M Chassis User's Guide
1-2
Table of Contents
Chapter I: Introduction ...............................................................1-3
A. Packing Lists............................................................................................... 1-3
B. Front Panel LED Indicators ....................................................................... 1-4
C. SC813/SC813M Chassis Specifications ................................................. 1-5
D. SC813/SC813MPower Supply Specifications........................................ 1-6
Chapter 2: Installation Procedures...........................................2-1
Section 1: Installing components into the SC813 Chassis....... 2-1
A. Removing the top Cover of the SC813 Chassis .................................. 2-1
B. Accessing the SCA Drive Tray to Install a Hard Drive....................... 2-2
C. Rail Installation........................................................................................... 2-3
D. Installing the Slide Assemblies into the Rack ....................................... 2-4
E. Installing the Chassis into the Rack........................................................ 2-5
Section 2: Appendix A: SCSI (Super) GEM Driver Installation
Instructions for Windows OS............................................................ 2-6

1-3
Chapter 1: Introduction
Chapter 1- Introduction
A. Packing Lists
A-1 The SC813 chassis
The SC813 chassis contains the following:
One (1) Slim CD ROM Drive [CDM-TEAC-24(B)]
Four (4) SCA 1" drive trays [CSE-PT39-(B)]
One (1) Slim 3.5" floppy drive [FPD-TEAC-S(B)]
Two (2) 100mm Blowers [FAN-0059]
One (1) Cold-swappable 500W power supply [PWS-0048]
One (1) Power supply backplane [CSE-PT813-PD520 for the SC813T/S-500
Series]
One (1) Power supply backplane [CSE-PT813-PD524 for the SC813T/S-500C
Series]
One (1) 4-port SATA backplane [CSE-SATA-813 (*for 813T)]
One (1) 4-port SCSI backplane [CSE-SCA-813S (*for 813S)]
The accessory box contains the following:
One set of motherboard screws
One set of drive screws
One set of HDD (hard disk drive) screws
One (1) AC power cord
Rail Packaging includes:
One pair of rear inner slides to be installed on the chassis
One pair of outer slides to be installed in the rack
Two pairs of short brackets to be used on the front side of the outer slides
(Note: One pair of short brackets include screw threads, and the other pair
do not. Use the only pair that will fit into your rack.)
One pair of long brackets to be used on the rear side of the outer slides
Optional Kits include:
The SC813 Series:
RiserCards[CSE-RRIU-X]
Low Profile Riser Cards [CSE-RRIU-XLP]
Front Bezel [CSE-PTFB-813(B)]
The SC813C Series:
Riser Cards (64-Bit) [CSE-RRIU-X]
Riser Cards(32-Bit) [CSE-RR32]
Front Bezel [CSE-PTFB-813(B)]

SC813/813M Chassis User's Guide
1-4
A-2 The SC813M chassis:
The SC813M chassis contains the following:
Four (4) SCA 1" drive trays [CSE-PT39(B)]
One (1) 350W Power Supply [PWS-042-24] (for the 350W Series)
One (1) 300 W Power Supply [PWS-0054] (for the 300W Series)
One (1) 420 W Power Supply [PWS-0053] (for the 420W Series)
Three (3) 40mm Fans [FAN-0061] (in the 300W & 350W Series)
Four (4) 40mm Fans [FAN-0061] (in the 420W & 500W Series)
One (1) 4-port SATA backplane [CSE-SATA-813] (*for the 813MT Series)]
One (1) 4-port SCSI backplane [CSESCA-813S] (*for the 813MS Series)]
The accessory box contains the following:
One set of motherboard screws
One set of drive screws
One set of HDD (hard disk drive) screws
One (1) AC power cord
(SC813/SC813M Front Panel)
LAN2
OH
LAN1 PWR On
Reset SW
PWR SW
B.FrontPanelLEDIndicators
One pair of outer slides to be installed in the rack
Two pairs of short brackets to be used on the front side of the outer slides
(Note: One pair of short brackets include screw threads, and the other pair
do not. Use the only pair that will fit into your rack.)
One pair of long brackets to be used on the rear side of the outer slides
HDD
Rail Packaging includes:
One pair of rear inner slides to be installed on the chassis
Optional Kits include:
The SC813M Series:
Riser Cards(64-Bit) [CSE-RRIU-X] or Riser Cards(32-Bit) [CSE-RR32-1U]
Front Bezel [CSE-PTFB-813(B)]

1-5
Chapter 1: Introduction
C. Specifications of the SC813/SC813M Chassis
C-1. Specifications of the SC813 Chassis
C-2. Specifications of the SC813M Chassis
Model SC813S-500/500C SC813T-500/500C
Form Factor 1U Rackmount 1U Rackmount
CPU Support Dual Xeon Processors Dual Xeon Processors
Max.
Motherboard Size
ATX 12” x 13” ATX 12” x 13”
Expansion Slots 2/1 2/1
SCA or HD Bays Four 1”hot-swap Ultra
320/160 SCSI drive bays
(SAF-TE Compliant)
Four 1”hot-swap SATA bays
Front Side USB
Port &COM port
Optional Optional
Floppy/CD-ROM Yes/Yes Yes/Yes
Power Supply 500W cold-swap PS 500W cold-swap PS
Cooling System Two 100mm blower fans Two 100mm blower fans
Dimension
(W x H x D)
17.2” x 1.7” x 25.6”
(437mm x 43mm x 650 mm)
17.2” x 1.7” x 25.6”
(437mm x. 43mm x 650mm)
Weight 35 lb.
(15.9 kg)
35 lb.
(15.9 kg)
Optional Kits Riser Cards, Front Bezel Riser Cards, Front Bezel
Model SC813MS-350C SC813MT-350C
Form Factor 1U Rackmount 1U Rackmount
CPU Support Dual Xeon Processors Dual Xeon Processors
Max.
Motherboard Size
ATX 12” x 10” ATX 12” x 10”
Expansion Slots 1 1
SCA or HD Bays Four 1”hot-swap Ultra 320/160
SCSI drive bays (SAF-TE
Compliant)
Four 1”hot-swap SATA bays
Front Side USB
Port & COM port
Yes Yes
Floppy/CD-ROM No/No No/No
Power Supply 420W/350W/300W PS 420W/350W/300W PS
Cooling System Three (3) 40mm blower fans Three (3) 40mm blower fans
Dimension
(W x H x D)
17.2” x 1.7” x 19.9”
(437mm x 43mm x 505.5 mm)
17.2” x 1.7” x 19.9”
(437mm x 43mm x 505.5 mm)
Weight 30 lb.
(13.6 kg)
30 lb.
(13.6 kg)
Optional Kits Riser Card, Front Bezel Riser Card, Front Bezel

SC813/813M Chassis User's Guide
1-6
D. Power Supply Specifications of the SC813/SC813M Chassis
D-1. Power Supply Specifications of the SC813 Chassis
D-2. Power Supply Specifications of the SC813M Chassis
Power Supply Spec SC813
Mfr. Model # SP502-IS
Mfr. Part # PWS-048
Rated AC Input Voltage 100-240V AC
Rated Input Frequency 50-60 Hz
Rated Input Current 10A (115V)
5A (230V)
Rated Output Power 500W
Maximum rated BTU 2750 BTUs/Hr
Nominal Output Vlotage
+3.3V 20A
+5 20A
+12 36A
-5 N/A
-12 1A
+5Vsb 2A
Serial # 300W Series 350W Series 420W Series
Mfr. Model # SP302-IS FSP350-60IU SP423-IS
Mfr. Part # PWS-0054 PWS-042-24 PWS-0053
Rated AC Input Voltage 100-240V AC 100-240V AC 100-240V AC
Rated Input Frequency 50-60 Hz 50-60 Hz 50-60 Hz
Rated Input Current 6A (115V)
3A (230V)
Rated Output Power 300W 350W 420W
Maximum rated BTU 1841 BTUs/Hr
Nominal Output Vlotage
+3.3V 15A 20A 18A
+5V 15A 25A 18A
+12V
1
15A 20A 15A
+12V
2
15A N/A 15A
+12V
3
N/A N/A 18A
+12V
total
20A 20A 32A
-5V N/A 0.3A N/A
-12V 1A 0.8A 1A
+5Vsb 2A 2A 2A

2-1
Chapter 2: Installation Procedures
A. Removing the top cover from the chassis
Before installing any components, replacing chassis fans or accessing the
motherboard, you will first need to remove the top cove from the chassis.
Procedures
1. Press the release tabs to release the top cover from its locking posi-
tion.
2. Slide the top cover out from the chassis as shown below:
3. You can now lift the side cover up and off the chassis.
Press the release buttons
Chapter 2: Installation Procedures
Section 1: Installing Components into the SC813
Chassis
Slide the top cover out
from the chassis

SC813 Chassis User's Guide
2-2
B. Accessing the SCA Drive Tray and Installing a Hard
Drive
To install the SCA drive into the chassis, you need to first remove the SCA
drive tray from the chassis so that the SCA drive can be installed in.
Procedures
1. Press the release tab to release the SCA drive tray from its locking
position.
2. Pull the SCA drive tray out from the chassis as shown below:
Pull out the SCA drive
tray from the chassis
Press the
release Tab
3. Remove the two screws that attach to the both sides of the dummy tray,
and take out the dummy tray as shown below:
Remove the
screws
Take out the dummy tray
4. Slide a hard drive disk (HDD) into the SCA drive tray, and secure the
HDD to the tray with three screws on each side of the tray as shown
below:
Secure the HDD with 3
screws on each side
of the tray
Slide HDD into the tray
5. Once the HDD is securely placed into the SCA tray, you can install the
SCA drive tray back to the chassis.

2-3
Chapter 2: Installation Procedures
C. Rail Installation
C-1 Installing Inner Slides
Procedures
1. Locate the right inner slide, (-the slide that will be used on the right side
of chassis when facing the front panel of the chassis).
2. Align the four(4) square holes on the right inner slide against the hooks
on the right side of the chassis as show below on the left.
3. Securely attach the slide to the chassis with two M4 flat head screws
and repeat the steps 1-3 to install the left inner slide to the left side of the
chassis.
Rail Packaging includes:
*One pair of inner slides to be installed on the chassis,
*One pair of outer slides to be installed in the rack,
*Two pairs of short brackets to be used on the front side of the outer slides
(Note: One pair of short brackets include screw threads, and the other pair
do not. Use the only pair that will fit into your rack.),
*One pair of long brackets to be used on the rear side of the outer slides
Four(4) hooks on the right
side of the chassis
Four 4 square holes on
the right inner slide
C-2 Installing Outer Slides
1. Measure the distance from the front rail of the rack to the rear rail of the
rack.
2. Attach a short bracket to the rear side of the right outer slide, and a long
bracket to the front side of the right outer slide as shown above on the
right.
3. Adjust the short and long brackets to the proper distance so that the
chassis can snugly fit into the rack.
4. Secure the slides to the cabinet with screws. Repeat steps 1-4 for the
left outer slide.
Slide the long bracket into
the short bracket
Adjust the distance
between the brackets
two M4 screws

SC813 Chassis User's Guide
2-4
1. After you have installed the short and long brackets to the outer slides,
you are ready to install the whole slide assemblies (-outer slides with short
and long brackets attached) to the rack. (See the previous page.)
2. Use M5 screws and washers to secure the slide assemblies into the
rack as shown below:
C-3 Installing the Slide Assemblies to the Rack
Procedures
Slide assemblies (-outer slides with
Secure the Slide
assemblies to the
rack with screws
and washers
M5 screws & washers
long & short brackets attached)