Supero SUPER STORAGE SYSTEM 6047R-E1CR36L User manual

®
SUPER STORAGE SYSTEM
6047R-E1CR36L
SUPER
USER’S MANUAL
1.0

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu-
mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn-
ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other repro-
ductive harm.
Manual Revision 1.0
Release Date: September 26, 2014
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2014 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the 6047R-E1CR36L. Installation
and maintainance should be performed by experienced technicians only.
The 6047R-E1CR36L is a high-end storage system based on the SC847BE1C-
R1K28LPB 4U rackmountable chassis and the X9DRD-EF dual processor
serverboard.
Manual Organization
Chapter 1: Introduction
The rst chapter provides a checklist of the main components included with the
system and describes the main features of the X9DRD-EF serverboard and the
SC847BE1C-R1K28LPB chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the 6047R-E1CR36L into a
rack and check out the server conguration prior to powering up the system. If your
server was ordered without processor and memory components, this chapter will
refer you to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: Standardized Safety Warnings
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
6047R-E1CR36L.

SUPERSTORAGESYSTEM 6047R-E1CR36L User's Manual
iv
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X9DRD-EF serverboard, including
the locations and functions of connections, headers and jumpers. Refer to this
chapter when adding or removing processors or main memory and when recong-
uring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC847BE1C-R1K28LPB chassis.
You should follow the procedures given in this chapter when installing, removing or
reconguring SATA or peripheral drives and when replacing system power supply
units and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed informa-
tion on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: System Specications

Notes
Preface
v

vi
Table of Contents
Chapter 1 Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Serverboard Features ..................................................................................... 1-2
Processors ...................................................................................................... 1-2
Memory ........................................................................................................... 1-2
Serial ATA........................................................................................................ 1-2
PCI Expansion Slots ....................................................................................... 1-2
Rear I/O Ports................................................................................................. 1-2
Rear I/O Ports................................................................................................. 1-2
1-3 Server Chassis Features ................................................................................ 1-3
System Power................................................................................................. 1-3
Hard Drives ..................................................................................................... 1-3
Front Control Panel......................................................................................... 1-3
Cooling System............................................................................................... 1-3
1-4 Contacting Supermicro.................................................................................... 1-6
Chapter 2 Server Installation
2-1 Overview ......................................................................................................... 2-1
2-2 Unpacking the System .................................................................................... 2-1
2-3 Preparing for Setup......................................................................................... 2-1
Choosing a Setup Location............................................................................. 2-1
Rack Precautions............................................................................................ 2-2
Server Precautions.......................................................................................... 2-2
Rack Mounting Considerations ....................................................................... 2-3
2-4 Rack Mounting Instructions............................................................................. 2-4
Rack Rails Assembly ...................................................................................... 2-4
Identifying the Inner Rack Rails...................................................................... 2-4
Installing the Inner Rails on the Chassis ........................................................ 2-5
Installing the Outer Rails onto a Rack............................................................ 2-6
Installing the Chassis into a Rack................................................................... 2-8
Chapter 3 System Interface
3-1 Overview ......................................................................................................... 3-1
3-2 Control Panel Buttons ..................................................................................... 3-1
Reset............................................................................................................... 3-1
Power .............................................................................................................. 3-1
3-3 Control Panel LEDs ........................................................................................ 3-2
Power Fail ....................................................................................................... 3-2
Overheat/Fan Fail ........................................................................................... 3-2
SUPERSTORAGESYSTEM 6047R-E1CR36L User's Manual

vii
NIC1 ................................................................................................................ 3-2
NIC2 ................................................................................................................ 3-3
HDD................................................................................................................. 3-3
Power .............................................................................................................. 3-3
3-4 Drive Carrier LEDs.......................................................................................... 3-3
Chapter 4 Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements....................................................... 4-1
Warning Denition ........................................................................................... 4-1
Installation Instructions.................................................................................... 4-4
Circuit Breaker ................................................................................................ 4-5
Power Disconnection Warning ........................................................................ 4-6
Equipment Installation..................................................................................... 4-8
Restricted Area................................................................................................ 4-9
Battery Handling............................................................................................ 4-10
Redundant Power Supplies .......................................................................... 4-12
Backplane Voltage ........................................................................................ 4-13
Comply with Local and National Electrical Codes........................................ 4-14
Product Disposal........................................................................................... 4-15
Hot Swap Fan Warning................................................................................. 4-16
Power Cable and AC Adapter ...................................................................... 4-18
Chapter 5 Advanced Serverboard Setup
5-1 Handling the Serverboard ............................................................................... 5-1
Precautions ..................................................................................................... 5-1
Unpacking ....................................................................................................... 5-2
5-2 Connecting Cables.......................................................................................... 5-2
Connecting Data Cables ................................................................................. 5-2
Connecting Power Cables .............................................................................. 5-2
Connecting the Control Panel......................................................................... 5-2
5-3 Rear I/O Ports................................................................................................. 5-3
5-4 Installing the Processor and Heatsink ............................................................ 5-4
Installing an LGA2011 Processor.................................................................... 5-4
Installing a Passive CPU Heatsink ................................................................. 5-7
Removing the Heatsink................................................................................... 5-7
5-5 Installing Memory............................................................................................ 5-8
Memory Support.............................................................................................. 5-8
DIMM Installation ............................................................................................ 5-8
5-6 Adding PCI Add-On Cards............................................................................ 5-13
5-7 Serverboard Details ...................................................................................... 5-14
X9DRD-EF Quick Reference ........................................................................ 5-14
Table of Contents

viii
5-8 Connector Denitions ................................................................................... 5-16
5-9 Jumper Settings ............................................................................................ 5-23
5-10 Onboard Indicators........................................................................................ 5-26
5-11 SATA Ports .................................................................................................... 5-27
5-12 Installing Software......................................................................................... 5-28
SuperDoctor® 5 ............................................................................................ 5-29
5-13 Onboard Battery............................................................................................ 5-30
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices.................................................................................. 6-1
Precautions ..................................................................................................... 6-1
Unpacking ....................................................................................................... 6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 Removing the Chassis Cover ......................................................................... 6-3
6-4 System Fans ................................................................................................... 6-4
System Fan Failure......................................................................................... 6-4
Replacing System Fans .................................................................................. 6-4
6-5 Drive Bay Installation/Removal ....................................................................... 6-5
Accessing the Drive Bays ............................................................................... 6-5
Hard Drive Installation..................................................................................... 6-6
Hard Drive Backplane ................................................................................ 6-7
Removing the Air Shroud................................................................................ 6-8
6-6 Installing Optional Fixed Hard Drives ............................................................ 6-9
6-7 Power Supply................................................................................................ 6-10
Power Supply Failure.................................................................................... 6-10
DC Power.......................................................................................................6-11
6-8 Attaching a JBOD Expansion Chassis...........................................................6-11
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
7-2 Main Setup...................................................................................................... 7-2
7-3 Advanced Setup Congurations...................................................................... 7-4
7-4 Event Logs .................................................................................................... 7-25
7-5 IPMI............................................................................................................... 7-27
7-6 Boot............................................................................................................... 7-29
7-7 Security......................................................................................................... 7-30
7-8 Save & Exit ................................................................................................... 7-31
Appendix A BIOS POST Error Codes
Appendix B System Specications
SUPERSTORAGESYSTEM 6047R-E1CR36L User's Manual

Chapter 1
Introduction
1-1 Overview
The 6047R-E1CR36L is a high-end storage system comprised of two main subsys-
tems: the SC847BE1C-R1K28LPB 4U/rackmount chassis and the X9DRD-EF dual
processor serverboard. Please refer to our web site for information on operating
systems that have been certied for use with the system (www.supermicro.com).
In addition to the serverboard and chassis, various hardware components have
been included with the 6047R-E1CR36L, as listed below:
•Two passive CPU heatsinks (SNK-P0048PS)
•Seven 8-cm system fans (FAN-0126L4)
•One air shroud (MCP-310-49004-0N)
•SATA Accessories
One 24-bay SAS/SATA backplane (BPN-SAS3-846EL1)
One 12-bay SAS/SATA backplane (BPN-SAS3-826EL1)
Thirty-six drive carriers (MCP-220-00075-0B)
•Dual JBOD expansion ports (AOM-SAS3-8I8E-LP)
•One rackmount kit (MCP-290-00057-0N)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
•Supermicro product manuals: http://www.supermicro.com/support/manuals/
•Product drivers and utilities: ftp://ftp.supermicro.com
•Product safety info: http://super-dev/about/policies/safety_information.cfm
Chapter 1: Introduction
1-1

1-2
SUPERSTORAGESYSTEM 6047R-E1CR36L User's Manual
1-2 Serverboard Features
The 6047R-E1CR36L is built around the X9DRD-EF, a dual processor serverboard
based on the Intel C602J chipset. Below are the main features of the X9DRD-EF.
(See Figure 1-1 for a block diagram of the chipset).
Processors
The X9DRD-EF supports single or dual Intel® Xeon E5-2600 (v2) Series processors.
Please refer to the serverboard description pages on our web site for a complete
listing of supported processors (www.supermicro.com).
Memory
The X9DRD-EF has 16 DIMM slots that can support up to 1 TB of Load Reduced
(LRDIMM), 512 GB of Registered (RDIMM) or 128 GB of Unbuffered (UDIMM) ECC/
Non-ECC DDR3-800/1066/1333/1600/1866 memory. See Chapter 5 for details.
Main Storage Controller
An AOC-S3008L-L8E disk controller is installed in the system to provide x8 lane
SAS3/SATA3 connectivity to all 36 drive bays. The 3008 controller is an IT mode/
JBOD mode controller meaning no RAID functions are provided by the controller
hardware.
PCI Expansion Slots
The X9DRD-EF has six PCI-E 3.0 x8 slots (Slot1/Slot2/Slot6 controlled by CPU1
and Slot3/Slot4/Slot5 controlled by CPU2).
Rear I/O Ports
The I/O ports include one COM port, a VGA port, four USB 2.0 ports (additional
USB headers are included on the serverboard), four gigabit Ethernet ports and two
external MiniSAS HD expansion ports. A dedicated IPMI LAN port is also included.

1-3
Chapter 1: Introduction
1-3 Server Chassis Features
The SC847BE1C-R1K28LPB is a 4U form factor chassis designed to be used in
a storage conguration. The following is a general outline of the main features of
the chassis.
System Power
The SC847BE1C-R1K28LPB features a redundant, hot-plug (two separate power
modules) 1280W high-efciency power supply with I2C. This power redundancy fea-
ture allows you to replace a failed power supply without shutting down the system.
Hard Drives
The SC847BE1C-R1K28LPB chassis was designed to support 36 SATA hard drives
(24 on the front of the chassis and 12 located on the rear of the chassis), which
are hot-swappable units.
Front Control Panel
The control panel on the front of the chassis provides you with system monitoring
and control. LEDs indicate system power, HDD activity, network activity, system
overheat/fan fail and power supply failure. A main power button and a system reset
button are also included. In addition, two USB ports and a COM port have been
incorporated into the front of the chassis for convenient access.
Cooling System
The SC847BE1C-R1K28LPB chassis includes seven 8-cm hot-plug system cooling
fans located in the middle section of the chassis. An air shroud channels the airow
from the system fans to efciently cool the processors and memory. Each power
supply module also includes a cooling fan.

1-4
SUPERSTORAGESYSTEM 6047R-E1CR36L User's Manual
Figure 1-1. Intel C602J Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
J23 SLOT#3 PCIE 3.0 x8 J24 SLOT#4 PCIE 3.0 x8 J25 SLOT#5 PCIE 3.0 x8
P0 P1
PE2
(AB)PE2 (CD)
PE1
(AB)DMI
DDR3 DIMM
CPU REAR
PROCESSOR
SANDYBRIDGE
PROCESSOR
SANDYBRIDGE
F
ESocket 01
#2
#1
DDR3 DIMM
#2
#1
PE3
J22 SLOT#2
PCIE 3.0 x8
PCIE 3.0 x8
PCIE 3.0 x8
PCIE 3.0 x4
SAS LSI
LAN1 LAN2
RJ45 RJ45
LAN3 LAN4
VGA CONN
IPMI LAN
PHY
RTL8201F
RJ45 RJ45
SAS2308
Powerville
I350-AM4
Quad GLAN
J26 SLOT#6
L-SAS0~3
L-SAS4~7
J21 SLOT#1
PCIE 3.0 x8
DDR3 DIMM
H
G
#2
#1
DDR3 DIMM
#2
#1
P1 P0
PE2
(AB)PE2 (CD) (AB)(CD)
PE1
(AB)PE3 DMI
PCH C602J
BIOS
SATA
SPI SATA Gen3
6Gbps
SATA Gen3
6Gbps
SATA
SATA [0..1]
SCU0
USB
LPCPCI 32
SPI FLASH
DDR3 DIMM
CPU FRONT
D
CSocket 00
#2
#1
#2
#1
PE3
DDR3 DIMM
B
A
#2
#1
DDR3 DIMM
QPI QPI
#2
#1
I-SATA0 I-SATA1
S-SATA0 S-SATA1 S-SATA2 S-SATA3
REAR
HDR 2X5
0,1
TYPE-A
REAR
2,3
4,5 6 8,9
HDR 2X5
TPM HDR Port 80
HERMON
WPCM450]
NCT7904D
HW Monitor
DDR3
DDR3 DIMM
(X9DRD-7LN4F series)
(X9DRD-7LN4F
series)

1-5
Chapter 1: Introduction
Figure 1-2. X9DRD-EF Serverboard
JPME1
JI2C1
VGA1
I-SATA1
I-SATA0
I-SATA5
I-SATA4
I-SATA3
I-SATA2
JIPMB1
JPME2
JPL1
JBR1
JWD1
JPG1
JPB1
JVRM_I2C1
JVRM_I2C2
JVR1
FAN5
FAN6
FAN8 FAN7
FAN1
FAN2
FAN3
FAN4
JF2
T-SGPIO1
T-SGPIO2
JUSB6
JSD1
JBT1
JBAT1
JTPM1
JF1
JPI2C1
JOH1
JI2C2
JL1
JSTBY1
JUIDB
J4
JD1
LED3
LEDM1
LED2
LAN2 LAN1
CPU1
CPU2
CPU2
CPU1
CPU2
CPU1
PWR I2C
UID
P2-DIMME1 P2-DIMMF2 P2-DIMMF1
P2-DIMMG2
P2-DIMMG1
P2-DIMMH2 P2-DIMMH1
P1-DIMMA2
P1-DIMMA1
P1-DIMMB2
P1-DIMMB1
P1-DIMMC1 P1-DIMMC2
P1-DIMMD1
P1-DIMMD2
USB4/5USB8/9
SLOT1 PCI-E 3.0 X8
SLOT2 PCI-E 3.0 X8
SLOT3 PCI-E 3.0 X8
SLOT4 PCI-E 3.0 X8
SLOT5 PCI-E 3.0 X8
USB6
TPM/PORT80
BUZZER
CMOS CLEAR
SLOT6 PCI-E 3.0 X8
COM2
USB2/3
COM1
USB0/1
SP1
IPMI_LAN
Battery
BIOS
JPW1
JPW2
24-Pin Main PWR
8-Pin PWR
JPW4
P2-DIMME2
JPW3
8-Pin PWR
4-Pin PWR
Intel
PCH
LAN
CTRL
BMC
X9DRD-EF
Rev. 1.02
CPU2
CPU1
1
11 2
Slot 1 as highlighted above is used for the JBOD expansion ports.
Slot 2 as highlighted above is used for the AOC-S3008L-L8E card.

1-6
SUPERSTORAGESYSTEM 6047R-E1CR36L User's Manual
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Website: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Website: www.supermicro.nl
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [email protected]
Website: www.supermicro.com.tw

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your SuperServer 6047R-
E1CR36L up and running. Following these steps in the order given should enable
you to have the system operational within a minimum amount of time. This quick
setup assumes that your system has come to you with the processors and memory
preinstalled. If your system is not already fully integrated with a serverboard, pro-
cessors, system memory etc., please turn to the chapter or section noted in each
step for details on installing specic components.
2-2 Unpacking the System
You should inspect the box the SuperServer 6047R-E1CR36L was shipped in and
note if it was damaged in any way. If the server itself shows damage you should
le a damage claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the SuperServer 6047R-
E1CR36L. It should be situated in a clean, dust-free area that is well ventilated.
Avoid areas where heat, electrical noise and electromagnetic elds are generated.
You will also need it placed near a grounded power outlet. Read the Rack and
Server Precautions in the next section.
2-3 Preparing for Setup
The box the SuperServer 6047R-E1CR36L was shipped in should include two
sets of rail assemblies, two rail mounting brackets and the mounting screws you
will need to install the system into the rack. Follow the steps in the order given to
complete the installation process in a minimum amount of time. Please read this
section in its entirety before you begin the installation procedure outlined in the
sections that follow.
Choosing a Setup Location
•Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufcient airow and ease in servicing.

2-2
SUPERSTORAGESYSTEM 6047R-E1CR36L User's Manual
•This product is for installation only in a Restricted Access Location (dedicated
equipment rooms, service closets and the like).
•This product is not suitable for use with visual display work place devices
acccording to §2 of the the German Ordinance for Work with Visual Display Units.
2-4 Warnings and Precautions
Rack Precautions
•Ensure that the leveling jacks on the bottom of the rack are fully extended to
the oor with the full weight of the rack resting on them.
•In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
•Always make sure the rack is stable before extending a component from the
rack.
•You should extend only one component at a time - extending two or more si-
multaneously may cause the rack to become unstable.
Server Precautions
•Review the electrical and general safety precautions in Chapter 4.
•Determine the placement of each component in the rack before you install the
rails.
•Install the heaviest server components on the bottom of the rack rst, and then
work up.
•Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
•Allow any hot plug drives and power supply modules to cool before touching
them.
•Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation
2-3
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating tempera-
ture of the rack environment may be greater than the room's ambient temperature.
Therefore, consideration should be given to installing the equipment in an environ-
ment compatible with the manufacturer’s maximum rated ambient temperature
(Tmra).
Reduced Airow
Equipment should be mounted into a rack so that the amount of airow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec-
tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).
Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:
•This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
•When mounting this unit in a partially lled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
•If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.

2-4
SUPERSTORAGESYSTEM 6047R-E1CR36L User's Manual
2-5 Rack Mounting Instructions
This section provides information on installing the chassis into a rack unit with the
rails provided. There are a variety of rack units on the market, which may mean
that the assembly procedure will differ slightly from the instructions provided. You
should also refer to the installation instructions that came with the rack unit you are
using. Note: This rail will t a rack between 26.5" and 36.4" deep
Identifying the Sections of the Rack Rails
The chassis package includes a rack rail assembly in the rack mounting kit. Each
assembly consists of three sections: An inner chassis rail which secures directly to
the chassis, an outer rail that secures to the rack, and a middle rail which extends
from the outer rail. These assemblies are specically designed for the left and right
side of the chassis.
Installing the Inner Rails on the Chassis
Installing the Inner Rails
1. Place the inner rails on the side of the chassis aligning the hooks of the chas-
sis with the inner rail holes. Make sure that the rail faces "outward" so that it
will t with the rack's mounting bracket.
2. Slide the rail toward the front of the chassis.
Figure 2-1. Identifying the Different Rail Sections
Inner Rail
Rail Assembly
(Shown with Rails
Retracted)
This Side Faces
Outward
Locking Tab
Middle Rail
Outer Rail

Chapter 2: Server Installation
2-5
Figure 2-2. Extending and Releasing the Inner Rail
3. Secure the rail to the chassis with four screws as illustrated.
4. Repeat steps 1-3 for the other inner rack rail.
Locking Tabs
Each inner rail has a locking tab. This tab locks the chassis into place when installed
and pushed fully into the rack. These tabs also lock the chassis in place when fully
extended from the rack. This prevents the server from coming completely out of
the rack when when the chassis is pulled out for servicing.
Releasing the Inner Rail
Releasing Inner Rail from the Outer Rails
1. Identify the left and right outer rail assemblies as described on page 5-4.
2. Pull the inner rail out of the outer rail until it is fully extended as illustrated
below.
3. Press the locking tab down to release the inner rail.
4. Pull the inner rail all the way out.
5. Repeat steps 1-3 for the second outer rail.
1
2
1
1
1
3
1
4

2-6
SUPERSTORAGESYSTEM 6047R-E1CR36L User's Manual
Warning: In any instance of pulling the system from the rack, always use
a rack lift and follow all associated safety precautions.
Warning: When initially installing the server to a rack, test that the rail
locking tabs engage to prevent the server from being overextended. Have
a rack lift in place as a precaution in case the test fails.
Figure 2-3. Installing the Inner Rails
Installing The Inner Rails on the Chassis
Installing the Inner Rails
1. Conrm that the left and right inner rails have been correctly identied.
2. Place the inner rail rmly against the side of the chassis, aligning the hooks
on the side of the chassis with the holes in the inner rail.
3. Slide the inner rail forward toward the front of the chassis until the rail clicks
into the locked position, which secures the inner rail to the chassis.
4. Secure the inner rail to the chassis with the screws provided.
5. Repeat steps 1 through 4 above for the other inner rail.
Note: chassis pictured may vary slightly from the 6047R-E1CR36L system chassis.
1
3
1
4
1
2
Inner Rails