Supero SUPERSERVER 6015TC-LFT User manual

SUPER
SUPERSERVER 6015TC-LFT
USER’S MANUAL
Revision 1.0
®

Manual Revision 1.0
Release Date: March 4, 2009
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2009 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software, if any,
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.
IN NO EVENT WILLSUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATASTORED OR USED WITH THE PRODUCT, INCLUDINGTHE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for
all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer 6015TC-LFT. In-
stallation and maintenance should be performed by experienced technicians only.
The SuperServer 6015TC-LFT is a 1UTwin (two serverboards in a 1U chassis) rack-
mount server based on the SC808T-780B server chassis and two Super X7DCT-LF
serverboards. X7DCT-LF supports dual Intel® Xeon® 5400/5300/5200/5100 Series
processors.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with the
server system and describes the main features of the Super X7DCT-LF serverboard
and the SC808T-780B chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 6015TC-LFT
into a rack and check out the server configuration prior to powering up the system. If
your server was ordered without the processor and memory components, this chap-
ter will refer you to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer to this chapter for details on the system interface, which includes the functions
and information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6015TC-LFT.
iii
Preface

SUPERSERVER 6015TC-LFT User's Manual
iv
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X7DCT-LF serverboard, including the
locations and functions of connectors, headers and jumpers. Refer to this chapter
when adding or removing processors or main memory and when reconfiguring the
serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC808T-780B 1U rackmount
server chassis. You should follow the procedures given in this chapter when install-
ing, removing or reconfiguring SAS/SATA or peripheral drives and when replacing
system power supply units and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed informa-
tion on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: Installing Windows OS
Appendix C: System Specifications

v
Preface
Notes

vi
SUPERSERVER 6015TC-LFT User's Manual
Table of Contents
Chapter 1 Introduction
1-1 Overview .........................................................................................................1-1
1-2 Serverboard Features..................................................................................... 1-2
Processors ......................................................................................................1-2
Memory ...........................................................................................................1-2
Serial ATA........................................................................................................1-2
PCI Expansion Slots....................................................................................... 1-2
Ethernet Ports................................................................................................. 1-2
Onboard Controllers/Ports .............................................................................. 1-3
ATI Graphics Controller...................................................................................1-3
Other Features................................................................................................1-3
1-3 Server Chassis Features ................................................................................ 1-5
System Power................................................................................................. 1-5
SATA Subsystem............................................................................................. 1-5
Control Panel .................................................................................................. 1-5
Rear I/O Panel................................................................................................ 1-5
Cooling System...............................................................................................1-5
1-4 1U Twin: System Notes................................................................................... 1-6
System Power................................................................................................. 1-6
SATA Backplane/Drives...................................................................................1-6
1-5 Contacting Supermicro....................................................................................1-7
Chapter 2 Server Installation
2-1 Overview .........................................................................................................2-1
2-2 Unpacking the System.................................................................................... 2-1
2-3 Preparing for Setup......................................................................................... 2-1
Choosing a Setup Location............................................................................. 2-1
Rack Precautions............................................................................................ 2-2
Server Precautions..........................................................................................2-2
Rack Mounting Considerations.......................................................................2-3
Ambient Operating Temperature................................................................ 2-3
Reduced Airflow .........................................................................................2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading..................................................................................... 2-3
Reliable Ground ......................................................................................... 2-3
2-4 Installing the System into a Rack ...................................................................2-4
Identifying the Sections of the Rack Rails......................................................2-4

vii
Table of Contents
Installing the Inner Rails ................................................................................. 2-4
Installing the Outer Rails.................................................................................2-5
Locking Tabs .............................................................................................. 2-5
Installing the Server into the Rack.................................................................. 2-6
Installing the Server into a Telco Rack...........................................................2-6
2-5 Checking the Serverboard Setup.................................................................... 2-6
2-6 Preparing to Power On................................................................................... 2-8
Chapter 3 System Interface
3-1 Overview .........................................................................................................3-1
3-2 Control Panel Buttons..................................................................................... 3-1
Reset...............................................................................................................3-1
Power..............................................................................................................3-1
3-3 Control Panel LEDs ........................................................................................3-2
Overheat/Fan Fail ........................................................................................... 3-2
NIC2................................................................................................................3-2
NIC1................................................................................................................3-2
HDD................................................................................................................. 3-2
Power..............................................................................................................3-3
3-4 SATA Drive Carrier LEDs................................................................................ 3-3
Chapter 4 System Safety
4-1 Electrical Safety Precautions..........................................................................4-1
4-2 General Safety Precautions............................................................................ 4-2
4-3 ESD Precautions............................................................................................. 4-3
4-4 Operating Precautions .................................................................................... 4-4
Chapter 5 Advanced Serverboard Setup
5-1 Handling the Serverboard............................................................................... 5-1
Precautions .....................................................................................................5-1
5-2 Serverboard Installation.................................................................................. 5-2
Unpacking .......................................................................................................5-2
5-3 Connecting Cables.......................................................................................... 5-3
Connecting Data Cables................................................................................. 5-3
Connecting Power Cables .............................................................................. 5-3
Connecting the Control Panel.........................................................................5-4
5-4 I/O Ports.......................................................................................................... 5-4
5-5 Processor and Heatsink Installation................................................................5-5
Installing the Processor .................................................................................5-5
Installing the Heatsink..................................................................................... 5-7
Removing the Heatsink...................................................................................5-7

viii
SUPERSERVER 6015TC-LFT User's Manual
5-6 Installing Memory............................................................................................5-8
5-7 Adding PCI Cards........................................................................................... 5-9
5-8 Serverboard Details ...................................................................................... 5-10
X7DCT-LF Quick Reference..........................................................................5-11
5-9 Connector Definitions....................................................................................5-12
5-10 Jumper Settings............................................................................................ 5-16
5-11 Onboard Indicators........................................................................................5-19
5-12 Installing Additional Drivers...........................................................................5-21
5-13 Configuring Supero Doctor III.......................................................................5-22
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices..................................................................................6-1
Precautions .....................................................................................................6-1
Unpacking .......................................................................................................6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 System Fans................................................................................................... 6-3
System Fan Failure......................................................................................... 6-3
6-4 Drive Bay Installation/Removal.......................................................................6-3
Accessing the Drive Bays............................................................................... 6-3
6-5 Power Supply..................................................................................................6-5
Power Supply Failure......................................................................................6-5
Replacing the Power Supply........................................................................... 6-5
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
7-2 Running Setup ................................................................................................ 7-2
7-3 Main BIOS Setup............................................................................................ 7-2
Main BIOS Setup Menu.................................................................................. 7-3
Main Setup Features.................................................................................. 7-3
7-4 Advanced Setup.............................................................................................. 7-6
7-5 Security ......................................................................................................... 7-22
7-6 Boot............................................................................................................... 7-23
7-7 Exit ................................................................................................................ 7-24
Appendix A BIOS POST Error Codes
Appendix B Installing the Windows OS
Appendix C System Specifications

Chapter 1
Introduction
1-1 Overview
The SuperServer 6015TC-LFT is a "1U Twin" server comprised of the SC808T-
780B 1U chassis and two (twin) X7DCT-LF serverboards. Please refer to our web
site for information on operating systems that have been certified for use with the
6015TC-LFT (www.supermicro.com).
In addition to the serverboard and chassis, various hardware components may have
been included with the 6015TC-LFT, as listed below.
Four (4) CPU heatsinks (SNK-P0017)
•
SATA Accessories:•
Four (4) SATA hard drive carriers (MCP-220-00001-03)
One (1) internal SATA backplane (BPN-SAS-808)
One (1) SATA cable set (CBL-0201L)
Two (2) PCI-E x16 riser cards (RSC-R1U-E16R)
•
Six (6) 4-cm high-performance fans (FAN-0085L4)•
Rackmount hardware with screws (CSE-PT51L):•
Two (2) rack rail assemblies
Six (6) brackets for mounting the rack rails in a rack/telco rack
One (1) CD containing drivers and utilities
•
SuperServer 6015TC-LFT User's Manual•
Chapter 1: Introduction
1-1

1-2
SUPERSERVER 6015TC-LFT User's Manual
1-2 Serverboard Features
At the heart of the SuperServer 6015TC-LFT are two X7DCT-LF dual processor
serverboards, which are based on Intel's 5100/ICH9R chipset. Below are the main
features of the X7DCT-LF. Note that the features on each board are doubled for
the server.
Processors
Each X7DCT-LF supports dual Intel® Xeon® 5400/5300/5200/5100 Series proces-
sors. Please refer to our web site for a complete listing of supported processors
(www.supermicro.com).
Memory
The X7DCT-LF has six 240-pin DIMM sockets that can support up to 48 GB of reg-
istered ECC DDR2-667/533 SDRAM. Memory can be installed in both interleaved
(dual-channel) and non-interleaved (single-channel) configurations. All memory
modules used to populate the system should be the same size, type and speed.
Serial ATA
The South Bridge (ICH9R) of the chipset includes a Serial ATA controller for six
Gb/s SATA drives. The hot-swappable SATA drives are connected to a backplane
that provides power, bus termination and configuration settings. RAID 0, 1, 5 (with
optional i-Button) and 10 are supported. Refer to the support area of our web site
for procedures on setting up RAID on your system.
PCI Expansion Slots
Each X7DCT-LF board has one PCI-Express 2.0 x16 slot, so two PCI-Express x16
slots are provided in the server. In the 6015TC-LFT server configuration, riser cards
have been pre-installed to support two low-profile PCI-Express x16 add-on cards.
Ethernet Ports
Two Intel® network controllers (Intel 82575) are integrated into each of the server-
boards to support a total of four Gigabit LAN ports (100/1000Base-T/1000BaseTX,
RJ45 output).

Chapter 1: Introduction
1-3
Onboard Controllers/Ports
Onboard I/O backpanel ports on each serverboard include one COM port, a VGA
port, two USB ports and two Gigabit LAN (NIC) ports. There are two sets of I/O
ports included in the server (one set for each serverboard).
ATI Graphics Controller
The X7DCT-LF features an integrated Winbond WPCM450 BMC graphics controller.
The WPCM450 includes support for IPMI 2.0.
Other Features
Other onboard features that promote system health include voltage monitors, a
chassis intrusion header, auto-switching voltage regulators, chassis and CPU
overheat sensors, virus protection and BIOS rescue.

1-4
SUPERSERVER 6015TC-LFT User's Manual
Figure 1-1. Intel 5100 Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
USB 2.0
3.0 Gb/S
Intel 5100
MCH
PROCESSOR#2
ICH9R
PCI-EXP x8
GILGAL
GB LAN
FWH
RJ45
RJ45
LPC
SIO
W83627GF
WPCM
PCI 33MHz
450BMC
VGA
CONN
KB
MS
PROCESSOR#1
1067/1333
MT/S
1067/1333
MT/S
USB
PCI-E x4
SATA
PCI-EXP x16
Oplin
82598
PCI-E SLOT
0-1
0-2
0-3
DIMMs
1-1
1-2
1-3
COM2COM1
82573V
JLAN1
82573L
JLAN2
PCI-EXP x1
PCI-EXP x1
DIMMs

Chapter 1: Introduction
1-5
1-3 Server Chassis Features
The following is a general outline of the main features of the SC808T-780B 1U
chassis. Details on the chassis can be found in Chapter 6.
System Power
When configured as a SuperServer 6015TC-LFT, the SC808T-780B includes a
single 780W cold-swap power supply, which provides the power to both server-
boards housed in the chassis.
SATA Subsystem
The SC808T-780B chassis was designed to support four SATA hard drives, which
are hot-swappable units.
Control Panel
The SC808T-780B features two independant control panels associated with each
serverboard in the chassis. Each control panel has LEDs to indicate power on, net-
work activity, hard disk drive activity and system overheat conditions. Each control
panel also includes a main power button and a system reset button.
Rear I/O Panel
The SC808T-780B is a 1U rackmount chassis. Its I/O panel provides a slots for two
low-profile PCI-E x16 expansion cards, two COM ports, four USB ports, two VGA
ports and four Gb Ethernet ports. See Chapter 6 for details.
Cooling System
The SC808T-780B chassis has an innovative cooling design that features two sets
of triple (for a total of six) 4-cm high-performance fans. A fan speed control setting
in BIOS allows fan speed to be determined by system temperature.

1-6
SUPERSERVER 6015TC-LFT User's Manual
1-4 1U Twin: System Notes
As a 1U Twin configuration, the 6015TC-LFT is a unique server system. With two
system boards incorporated into a single chassis, there are several points you
should keep in mind.
System Power
A single power supply is used to provide the power for both serverboards. Each
serverboard however, can be shut down independently of the other with the power
button on its own control panel.
Although they share a common power supply, the I2C signals used for power supply
monitoring are received by the primary serverboard only. (When viewed from the
front of the chassis, the serverboard on the left is referred to as the primary board
and the serverboard on the right as the secondary.)
SATA Backplane/Drives
As a system, the 6015TC-LFT supports the use of four SATA drives. The SATA
backplane works as a single backplane divided into two sections. This means that
while a single power connector is used and functions such as overheating apply to
both sections together, each pair of SATA drives is logically connected to its own
serverboard. Consequently, RAID setup is limited to a two-drive scheme (RAID
cannot be spread across all four drives).

Chapter 1: Introduction
1-7
1-5 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Pacific
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [email protected]
Tel: [phone], ext.132 or 139

1-8
SUPERSERVER 6015TC-LFT User's Manual
Notes

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get your 6015TC-LFT up and
running. Following these steps in the order given should enable you to have the
system operational within a minimum amount of time. This quick setup assumes
that your system has come to you with the processors and memory preinstalled. If
your system is not already fully integrated with a serverboard, processors, system
memory etc., please turn to the chapter or section noted in each step for details on
installing specific components.
2-2 Unpacking the System
You should inspect the box the 6015TC-LFT was shipped in and note if it was dam-
aged in any way. If the server itself shows damage you should file a damage claim
with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the 6015TC-LFT. It
should be situated in a clean, dust-free area that is well ventilated. Avoid areas
where heat, electrical noise and electromagnetic fields are generated. You will also
need it placed near a grounded power outlet. Be sure to read the Rack and Server
Precautions in the next section.
2-3 Preparing for Setup
The box the 6015TC-LFT was shipped in should include two sets of rail assemblies,
two rail mounting brackets and the mounting screws you will need to install the
system into the rack. Follow the steps in the order given to complete the installation
process in a minimum amount of time. Please read this section in its entirety before
you begin the installation procedure outlined in the sections that follow.
Choosing a Setup Location
Leave enough clearance in front of the rack to enable you to open the front•
door completely (~25 inches).
Leave approximately 30 inches of clearance in the back of the rack to allow for
•
sufficient airflow and ease in servicing.

2-2
SUPERSERVER 6015TC-LFT User's Manual
This product is for installation only in a Restricted Access Location (dedicated•
equipment rooms, service closets and the like).
This product is not suitable for use with visual display work place devices accord-
•
ing to §2 of the the German Ordinance for Work with Visual Display Units.
Rack Precautions
!
!
Warnings and Precautions!
Ensure that the leveling jacks on the bottom of the rack are fully extended to•
the floor with the full weight of the rack resting on them.
In single rack installation, stabilizers should be attached to the rack.
•
In multiple rack installations, the racks should be coupled together.•
Always make sure the rack is stable before extending a component from the•
rack.
You should extend only one component at a time - extending two or more si-
•
multaneously may cause the rack to become unstable.
Server Precautions
Review the electrical and general safety precautions in Chapter 4.•
Determine the placement of each component in the rack• before you install the
rails.
Install the heaviest server components on the bottom of the rack first, and then
•
work up.
Use a regulating uninterruptible power supply (UPS) to protect the server from
•
power surges, voltage spikes and to keep your system operating in case of a
power failure.
Allow the hot plug SATAdrives and power supply modules to cool before touch-
•
ing them.

Chapter 2: Server Installation
2-3
Always keep the rack's front door and all panels and components on the servers•
closed when not servicing to maintain proper cooling.
Make sure all power and data cables are properly connected and not blocking
•
the chassis airflow. See Chapter 5 for details on cable connections.
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating tempera-
ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera-
ture (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec-
tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).

2-4
SUPERSERVER 6015TC-LFT User's Manual
2-4 Installing the System into a Rack
This section provides information on installing the 6015TC-LFT into a rack unit with
the rack rails provided. If the system has already been mounted into a rack, you
can skip ahead to Sections 2-5 and 2-6.
There are a variety of rack units on the market, which may mean the assembly
procedure will differ slightly. You should also refer to the installation instructions that
came with the rack unit you are using.
Identifying the Sections of the Rack Rails
You should have received two rack rail assemblies in the rack mounting kit. Each
assembly consists of two sections: an inner fixed chassis rail that secures directly
to the server chassis and an outer fixed rack rail that secures directly to the rack
itself (see Figure 2-1). Two pairs of short brackets to be used on the front side of
the outer rails are also included.
Installing the Inner Rails
Both the left and right side inner rails have been pre-attached to the chassis. Pro-
ceed to the next step.
Figure 2-1. Identifying the Sections of the Rack Rails
(right side rail shown)