Superrollo GW70 User manual

BA10070-2 (03.16)
Electronic Roller Shutter Belt Winder superrollo GW70
Translation of the Original Operating and Assembly Manual
EN
Item No.
SR10070

2
EN
With your purchase of a roller shutter belt winder
superrollo GW70, you have chosen a quality product
manufactured by superrollo. Thank you for the trust
you have placed in us.
Dear Customer,
i

3
EN
Table of Contents
i
i Dear Customer, .............................................................2
1. These instructions ... ....................................................4
1.1 Application of this manual................................................. 4
2. Hazard symbols ............................................................4
2.1 Levels of danger and signal words.................................. 5
2.2 Symbols and depictions used .......................................... 5
3. Overview superrollo GW70 ........................................6
4. Functional description ................................................7
4.1 Description of the safety functions................................. 7
5. Technical Specications ..............................................8
5.1 Permissible roller shutter belts ......................................... 9
6. Safety instructions .....................................................10
6.1 Intended use..........................................................................11
6.2 Improper use.........................................................................12
6.3 Required expert knowledge of the installer ..............13
7. Safety instructions for the installation...................13
7.1 You will require the following tools ..............................14
8. Preparation for installation ......................................15
9. Safety instructions for the electrical
connection...................................................................18
9.1 Electrical connection..........................................................18
10. Feed the belt through and screw on the GW70....19
11. End point adjustment................................................21
12. Manual operation.......................................................23
13. Automatic timer; brief description .........................24
13.1 Conguring an opening and closing time .................24
13.2 Switching the automatic timer on / o........................25
14. Automatic solar function; brief description..........26
14.1 Automatic solar function; setting sensivity................28
15. Erase all settings, reset..............................................29
16. Removing the superrollo
(e.g. in the event of a move).....................................30
17. Removing the belt in the event of unit failure .....32
18. What to do if... ? ..........................................................33
19. Information about maintenance and care of
your equipment..........................................................36
20. CE Mark and EC Declaration of Conformity...........37
21. Warranty conditions ..................................................38

4
EN
1. These instructions ...
...describes how to install, connect the electrical system
and operate your roller shutter belt winder.
i
1.1 Application of this manual
The following hazard symbols are used in this
instruction manual: Danger of fatal electric shock
Danger area / dangerous situation
i
◆Before you begin, please read this manual through
completely and follow all the safety instructions.
◆This manual is a component of the product.
Please store it in an easily accessible place.
◆When passing the superrollo GW70 on to a third
party, this manual must be passed on as well.
◆Damage resulting from non-compliance with these
instructions and safety instructions will void the
guarantee. We shall assume no liability for any con-
sequential damage.
2. Hazard symbols
i

5
EN
i
2.1 Levels of danger and signal words
DANGER!
This hazard will result in serious injury or death if not
avoided.
CAUTION!
This hazard may result in minor or moderate injury
if not avoided.
WARNING!
This hazard may result in serious injury or death if not
avoided.
ATTENTION!
This hazard may lead to property damage.
2.2 Symbols and depictions used
i
Depiction Description
1. Steps to be taken
2.
◆Itemisation
or a) List
Please read the respective manual
i
further useful
information

6
EN







 






3. Overview superrollo GW70
i
Belt entry
Fixing hole
Drive release
Up button
Down button
Clock button
Sun button
Fixing hole
Plug connection for sunlight-/ twilight
sensor
Sun-LED
Automatic-LED
Set button
Plug with belt guide
Winding wheel compartment with cover
Electric cable in cable channel
Check the details on the type plate
Check that the voltage / frequency on the type
plate corresponds to the local mains conditions.

7
EN
i
4. Functional description
The roller shutter belt winder is a roller shutter drive
designed for use inside. The unit is installed as a surface
mounted device. The power supply is provided via an
connecting cable with mains plug
4.1 Description of the safety functions
Safety shut o
If the motor is turned on and the roller shutter belt
doesn’t move, the safety shut o will turn o the motor.
The motor cannot be run in the original direction until
the obstruction has been eliminated (pulled free) and the
motor has been run in the opposite direction.
Overview of functions
◆Manual operation
◆AUTO/MANU - switch
◆Automatic mode, with a separate switching time
for UP (▲ ) and DOWN ( t )
◆Automatic solar function
◆End point setting
◆Permanent storage of the settings
◆Deleting the data (Reset)
When the motor is overloaded due to technical defects,
mechanics which run with diculty or ice on the roller
shutters, the motor will shut o. Eliminate the cause and
if necessary correct the end position..
i

8
EN
i
5. Technical Specications
Technical specifcations
Supply voltage: 230 V ~ / 50 Hz
Nominal power: approx. 70 W
Consumption: Standby: approx. 1 W
Nominal torque: approx. 8 Nm
Maximum tractive force: 30 Kg
Transient operation (KB): 4 minutes
(maximum running time)
Overrun: < 0.4 Revolutions
Protection class: II (only for use in dry rooms)
Number of switching times: 2 (up and down)
Max. shutter surface area:
(plastic roller shutters) 5 m2
Permissible ambient
temperature: approx. 40 °C
Automatic solar function
setting range 2,000 to 20,000 Lux
Sound pressure
level (LpA): ≤ 70 dB(A)
Power failure
The automatic LED ashes in the event of a power
failure.
The automatic LED lights up permanently again after
pressing the UP ( ▲) or DOWN ( t) button.
Data retention subsequently to power failure
The configured switching times are retained after a
power failure. As soon as the power supply is restored,
the opening and closing times will be executed again.
However, the times will be oset by the duration of the
power failure.
Example:
◆Power failure from 19:30 - 19:45 hours.
◆The closing time was previously set to 19:30 hours.
◆The roller shutters will close at 19:45 hours due to
the duration of the power failure.

9
EN
5.1 Permissible roller shutter belts
i
ATTENTION!
The superrollo GW70 may be damaged if excessively
long belts are used.
◆Only use belts of the permissible lengths
◆Depending on the belt width, use one of the en-
closed guides, see page 17.
i
The specications are intended for guidance
only and apply to an ideal installation
situation.
The actual values may vary due to local
conditions.
Table 1: Permissible roller shutter belts
superollo:
Item No.:
GW70
SR10070
Belt width: Belt thick-
ness Maximum belt length
15 mm (Mini belt) 1.0 mm 4.0
23 mm (Standard belt)
1.0 mm 5 m
1.3 mm 4 m
1.5 mm 3.4 m
Table 2: Permissible shutter surface area (m2)
Roller shutter type: Weight/m2Permissible shutter surface area (m2)
Plastic roller shutters (4.5 kg/m2) Approx. 5 m2

10
EN
6. Safety instructions
The use of defective equipment can lead to personal
injury and damage to property (electric shocks, short
circuiting).
◆Never use defective or damaged equipment.
◆Check the superrollo GW70 and the provided
mains cable beforehand for damage.
◆Should you discover damage to the equipment,
please consult our customer service department
(see page 40).
i
◆Children must not play with the device.
◆Cleaning and user maintenance may not be carried
out by children without supervision.
◆Watch the moving roller shutters whilst carrying out
the settings and during normal operation, and keep
other people away from the area to avoid injury in
the event the shutters suddenly slip.
◆Carry out all cleaning work on the roller shutters
whilst the device is disconnected from the mains
power.
Incorrect use leads to an increased risk of injury.
◆Train all personnel to use the superrollo GW70
safely.
◆This device may be used by children from 8 years
of age upwards as well as by persons with reduced
physical, sensory or mental capacities or with lack
of experience and knowledge if they are supervised
or have been instructed on how to use the device
safely and if they understand what dangers may
resulted from this.
When using a cable with mains power plug, the power
outlet and mains plug must be easily accessible at
all ‘ times.

11
EN
i
Exceeding the maximum permissible running time
(KB) may overload and damage the roller shutter
belöt winder.
◆The maximum permissible running time for a cycle
may not be exceeded when the equipment is in
operation. For this reason, the roller shutter belt
winder has an automatic running time limit (KB)
of four minutes.
◆If the running time limit is triggered, then the
roller shutter belt winder must be left for at least
30 minutes to cool down. Full operational availability
is re-established after approx. one hour
According to DIN EN 13659, it is necessary to determine
that the movement conditions for the shutters are
maintained in accordance with EN 12045.
◆The displacement must be of at least 40 mm on the
lower edge in the rolled-out position with a force of
150 N in the upwards direction.
◆In doing so, it must be ensured that the extending
speed of the shutters for the nal 0.4 m is less than
0.15 m/s.
6. Safety instructions
i
6.1 Intended use
Only use the roller shutter belt winder for opening and
closing roller shutters with a permissible belt.
i
Mechanical locks of any kind are not suitable
for automated operation with this device.

12
EN
Only use original spare parts from superollo.
◆By doing so, you avoid risk of malfunctions and
damage to your roller shutter belt winder.
◆As the manufacturer, we provide no guarantee for
the use of third-party components and accept no li-
ability for consequential damage resulting from such.
◆All repairs to the roller shutter belt winder must be
undertaken by authorised customer service person-
nel.
Operating conditions
◆Only operate the roller shutter belt winder in dry
rooms.
◆An easily accessible 230 V / 50 Hz socket must be
available at the installation site if the enclosed con-
necting cable with Euro plug is being used.
◆The roller shutters must run up and down smoothly
and should not stick.
◆The mounting surface for the roller shutter belt
winder must be at.
6.2 Improper use
Using the roller shutter belt winder for purposes other
than previously mentioned is impermissible. There is a risk to life caused through short circuiting
and electric shocks if the roller shutter belt winder
is used outside.
◆Never install or operate the roller shutter beltr winder
outside.
6.1 Intended use
i
i

13
EN
i
6.3 Required expert knowledge of the installer
The electrical connection, installation and commission-
ing of the roller shutter belt winder must only be carried
out by a qualied electrician in accordance with the
instructions in this manual.
7. Safety instructions for the installation
Poor routing of the belt can cause the belt to fail and
leads to unnecessary loads on the roller shutter belt
winder.
◆Install the belt winder so that the belt runs as straight
as possible into the device, in order to avoid unneces-
sary friction and wear.
Incorrect installation can lead to property damage.
Strong forces are exerted during operation of the
system which require secure installation on a rm base.
i

14
EN
1
2
3
4
5
6 mm
7.1 You will require the following tools
◆Screwdriver
◆Phillips screwdriver
◆Scissors
◆Carpenter’s gauge or measuring tape
◆Pen
◆A drilling machine and a 6 mm masonry drill if
there are no installation holes.
i

15
EN
8. Preparation for installation
i
1. Take measurements. Check that the installation site
has sucient space for the roller shutter belt winder..
2. Remove the old belt winder, if you are carrying out a
conversion to an existing roller shutter system.
2.1 Let the roller shutter move fully down, until the slats
are completely closed.
2.2 Remove the old belt winder and unreel the belt.
CAUTION!
There is a risk of injury from the pre-tensioned
springs on the old belt winder.
◆The spring unit of the old belt winder may suddenly
recoil when it is removed.
◆Hold the spring unit rmly when loosening the belt
and allow it to recoil slowly until the spring unit has
completely unwound.

16
EN
20 cm
8. Preparation for installation
i
3. Use existing holes.
Hold the device on the wall and see if you can use exist-
ing holes, for example, those for the old belt winder. If
not, you must mark where the new holes are needed
and bore them.
4. Prepare the belt.
4.1 Cut the belt o approx. 20 cm under the mounting
position.
4.2 Fold the end of the belt over by approx. 2 cm and cut a
short slit in the centre.This enables you to subsequently
hook the belt onto the reel.
Recommendation
The belt must run as straight and freely as possible.
For sti roller shutters, mount a deection roller on
the belt box. This helps to prevent unnecessary friction
and wear to the belt.

17
EN
 
i
8. Preparation for installation
5. Exchange belt guide (only for mini belts).
= Plug in the belt guide
= Belt guide (dependant on the width of the belt)
◆The manufacturer equips the GW70 with a guide for
the standard belt width (23 mm).The guide makes it
possible to precisely guide the band.
◆To use mini belts (15 mm), you must exchange the
belt guide with the enclosed guide. The guide can
be exchanged on the back side of the GW70 with a
screw driver.

18
EN

There is a risk of fatal electric shock when touching
electrical components.
◆Carry out all installation and connection work in an
isolated and de-energised state.
◆Disconnect all phases of the mains power supply
cable and secure it to prevent any reconnection.
◆Check that the system is de-energised.
9. Safety instructions for the electrical connection
i
9.1 Electrical connection
i
1. Plug in the enclosed cable and screw until secure.
2. Finally, put the electrical cord in the cable channel and
screw the enclosed cover until it is tight.
A damaged connecting cable may cause a short
circuit.
◆Ensure that the connecting cable is laid safely.
◆The connecting cable muse not be pinched or
damaged when screwing on the roller shutter belt
winder.

19
EN



1. Open the winding wheel cover .
10. Feed the belt through and screw on the GW70
i
CAUTION!
There is a risk of injury from the turning winding
whheel .
Never reach into the winding wheel compartment
when the motor is running.
2. Check the position of the xing hook and if neces-
sary correct.
The xing hookn on the winding wheel must be
easily reached. If not:
2.1 Insert the mains plug into the socket.
2.2 Press the [ Up ] button until the xing hook 
in the winding wheel compartment is easy to
reach.
2.3 Remove the mains plug again from the socket.

20
EN

3. Push the belt into the GW70 and pull the slit over the
xing hook from below.
4. Close the winding wheel cover again.
i
10. Feed the belt through and screw on the GW70
5. Screw the GW70 on with the enclosed screws.
6. Finally insert the mains plug into the socket.