SUPRENT HC415SA User manual

This user manual tries to ensure the accuracy of
the information, please kindly point it out for
our improvement in the future, if there is any
errors on the images or the texts. We'd be very
appreciated for your support and effort.
In addition: If the technique of the trimmer has
been improved, it will be upgraded and updated
in the new version as well as the specification
without announcement.
HC415SA SUPRENT Hair Clipper

CONTENTS
Parts Name · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 1
Safety Instructions · · · · · · · · · · · · · · · · · · · · · · · · · · · 3
Steps for Hair Cutting · · · · · · · · · · · · · · · · · · · · · · · · 5
Disposal · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 10
Warranty Certificate · · · · · · · · · · · · · · · · · · · · · · · · · 11

Oil
To maintain your clipper in peak condition, the
blades should be oiled every few haircuts.
Do not use hair oil, grease,oil mixed with kerosene
or any solvent. As the solvent will evaporate and
leave the thick oil which may slow down the
motion of the blades.
Blade Adjustable Knob
The knob is conveniently located near your thumb (if you’re right-
handed) so it can easily be adjusted while the clipper is in your hand.
The Knob adds versatility to the clipper by allowing a gradual change
to the closeness of a cut without an attachment comb.
When the Lever is in the uppermost position, the Blades will give the
closest cut leaving the hair very short. Pushing the Lever gradually
downward increases the cutting length
● There’re 3 settings of the length: 0.9/1.2/1.5mm The Lever will also
extend the use of the blades since a different cutting edge is used
in each setting.
● In addition, if extremely heavy hair cutting
has jammed the blades, it will help to
remove hair that has become wedged
between the two blades without removing
the blades.
● While the clipper is running, move the knob
from "close cut" to "long cut" a couple of
times. Doing this each time after use will
help to keep the blades clear of cut hair.
Blade Alignment
Your clippers were carefully examined to ensure that the blades were
oiled and aligned before leaving our factory. Blades must be realigned
if they have been removed for cleaning or replacement. To realign the
blades, simply match the upper and bottom blades teeth up, point for
point. (End of top blade teeth should be approximately 1.2mm back
from the bottom blade. Compare your clipper blades with the sketch.)
1 2
bottom blade
top blade
on/off switch
3mm
9mm
6mm
12mm
comb sclssors
1.2mm
oil brush
blade lever
PARTS NAMEPARTS NAME

Cleaning
Never clean the appliance under running water! Use the included brush
to remove hair. Wipe the enclosure with a dry, soft cloth. Do not use
abrasive cleaning agents.
Important Safeguards
When using electrical appliances, especially when children are present,
basic safety precautions should always be followed, including the
following:
To reduce the risk of death or injury by electric shock:
● Unplug this appliance before cleaning.
● Do not place or store appliance where it can fall or be pulled into a tub
or sink.
● Do not use while bathing or in a shower.
● Do not place in, or drop into, water or other liquid.
● Do not reach for an appliance that has fallen into water. Unplug
immediately.
To reduce the risk of burn, electrocution, fire or injury to persons:
● Use this appliance only for its intended use as described in this
manual. Do not use attachments not recommended by the
manufacturer.
● This appliance should never be left unattended when plugged in.
● This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible
for their safety.
● Children should be supervised to ensure that they do not play with
the appliance.
● Never operate this appliance if it has a damaged cord or plug, if it is
not working properly.
● If the supply cord is damaged, i t must be replaced by the manufac-
turer or its service agent or a similarly qualified person in order to
avoid a hazard.
● Keep the cord away from heated surfaces.
● Do not pull, twist, or wrap line cord around appliance.
● Never drop or insert any object into any opening on this appliance.
● Before use, making certain blades are aligned properly.
● Do not place appliance on any surface while it is operating.
● Do not use this appliance with a damaged or broken comb nor with
teeth missing from the blades as injury may occur.
● Do not use with wet hands.
3 4
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS

Begining The Hair Cut
Cutting hair requires practice so It is always better to leave the hair
longer for the first few haircuts until you become used to the length
to which each comb attachment cuts the hair.
Attachment Comb (see main diagram)
●Attachment Comb #1 leaves 3mm (1/8 inch) hair length.
●Attachment Comb #2 leaves 6mm (1/4 inch) hair length.
●Attachment Comb #3 leaves 9mm (3/8 inch) hair length.
●Attachment Comb #4 leaves 12mm (1/2 inch) hair length.
Each comb attachment is marked accordingly on its outside middle
surface.
●To attach a comb, hold it with its teeth upward and slide it onto and
along the clipper blade until the front of the comb firmly seats against
the clipper blade.
●To remove the comb, simply pull the comb upward and away from the
clipper blade.
●For even cutting, allow the comb attachment/cutter through quickly.
Also remember to comb the hair frequently to remove trimmed hair
and to check for uneven strands.
Before The Hair Cut
1. Inspect the clipper, making sure that it is free of oil between the
cutting blade teeth and turn the unit on to distribute the oil and to
make sure it is running smoothly. Wipe off any excess oil. This should
be done after each use. While using the unit, untwist the cord from
time to time to avoid tangling.
2. Seat the person so their head is approximately at your eye level. This
allows ease of visibility while cutting and a relaxed control of the unit.
3. Before cutting always first comb the hair so it is tangle free and as it
is naturally worn.
Reminders
● Cut the hair in a relaxed and slow manner. Use short strokes only to
work gradually over the entire head.
● Always take off a little hair at a time; you can always trim off additional
hair later.
● As you work, comb the hair frequently back into the style to which
you are cutting.
● When cutting with this Clipper it is better to leave the hair dry, not
wet. With the hair dry, it is much easier to control the amount of
hair being cut.4.Place a towel around the neck and shoulders of the
person having the haircut.
5 6
STEPS FOR HAIR CUTTING STEPS FOR HAIR CUTTING