SUPRENT HC315 User manual

Speed Indication
2 speed modes are available: Standard Mode and Turbo Mode
Power Button
Short press the power button to turn it on or off.
Long press the switch to change the gear mode (TURBO).
Cutting Length Adjustment of Blade
Adjusting the ring to choose the hair length that you
ant to remain ranges are: 0.8/1.1/1.4/1.7/2.0 mm.
Different sizes of combs are available for you to
remain different length of hair, the size includes: 3/6/9/12mm.
Charging Methods
This product contains a lithium battery with a capacity of 1400mAh The
charging time is about 2 hours.
After the product is fully charged, the running time is no less than 180 minutes.
Battery /Charging Reminder
When charging, the corresponding battery indicator flashes.
When the battery power is lower than 20%, the corresponding
indicator flashes.
*Note:When the power is too insufficient to be turned on,
please charge it immediately. If it is not used for a long time,
please fully charge it at least once every six months.
DIGITAL SCREEN FUNCTION DESCRIPTION
Blade
Charge Display
Cutting Length Switch
USB CableGuide Comb
Cleaning Brush
Oil
Speed Button
Power Button

Before the Hair Cut
1.Inspect the clipper, making sure that it is free of oil between the cutting blade
teeth and turn the unit on to distribute the oil and to make sure it is running
smoothly. Wipe off any excess oil.
2.Before cutting always first comb the hair so it is tangle free and as it is
naturally worn.
Attachment Guide Combs
Cutting hair requires practice so It is always better to leave the hair longer for
the first few haircuts until you become used to the length to which each comb
attachment cuts the hair.
Step 2-Back of The Head
• Change to the next longest comb attachment 9mm or 12mm and cut the back of the
head.(See diagram 2)
Step 3-Side of The Head
• Change to one of the shorter combs 3mm or 6mm, trim sideburns, i.e. the hair directly
in front of the ears. Change to one of the longercombs, 9mm or 12mm, and continue to
cut to the top of the head.
(See diagram 3)
Step 1-Nape of The Neck
• Attach comb attachment 3mm or 6mm.
• Hold the clipper cutting edge pointed up and begin the haircut, starting at the centre
of the head at the base of the neck .
(See diagram 1)
• Hold the clipper comfortably in your hand and hold lightly against the head with the
comb teeth pointing upward. Gradually and slowly lift the clipper working upwards and
outwards, through the hair, trimming just a little at a time.
• As you cut, gradually lift the clipper head towards you. Continue to cut the back area
from the bottom of the neck upwards to the top of the ears.
1. Guide combs should be installed by first hooking the blade teeth front side of
guide comb. Then press the back of the guide comb down until it snaps into
place. (See picture on the right)
2. Ensure comb is attached before beginning to cut hair.
3. To remove, pull the snap tab on back side of guide comb and pull the comb off.
Notes: The first time you cut hair, cut only a small amount of hair until you become accustomed
to the length of hair each guide comb provides-Start by attaching the largest guide comb on the
clipper.
-Then use shorter guide combs if a shorter length is desired.
-For uniform cutting, cut at a slow, even speed.
BASIC PARAMETERS
STEPS FOR HAIR CUTTING
STEPS FOR HAIR CUTTING
Motor ：Voltage：3.2V
Speed：7000RPM Decibel: ≤65dB
Charging Interface: Type-C
Battery: Type: Lithium Battery
Power Supply Input: DC 5V 1A
Battery Capacity: 1400mAh
Charging Time: 2H
Running Time: 3H

Step 5-The Finishing Touch
• Finally, use the Taper Lever without an attachment comb for close trimming
around the base of the neck, the sides of the neck and the ears.
• To produce a clean straight line at the sideburns, reverse the clipper by turning
the reverse side uppermost .
(See diagram 7)
• Press the clipper at right angles to the head,
tips of the blades lightly touching the skin and
work downwards. This way will obtain, as a clean
cut as would be given by a razor.
1. Unit must be off. Hold unit securely in one hand Grip blade and push with
your thumb the top of the blade away from the unit.
2. Adjust the scale at the bottom to 2.0 mm before
moving the cutter head off the retaining snaps.
3. Pull blade away from unit.
Reverse order to reattach blade.
4. Use the brush included to remove the accumulated hair from the cutters.
5. Clean the cutter head of the hair clipper with a damp cloth or under
running water.
Blades Maintenance
Blades Maintenance is recommended to oil the blades after every use.
Place 2 to 3 drops of lubricating oil on the moving blade and turn on
the clipper.
Step 4-Top of The Head
• Using the comb attachment 9mm or 12mm, cut top of head from back to front
against the direction in which the hair normally grows. In some cases, this may
require the reverse, or cutting from front to back.
(See diagram 4)
• Comb attachments 3mm or 6mm are used to achieve a close crew cut or
short cut.
• For longer hair on top, use the comb provided and lifts hair on the top of the
head. Cutover the comb, with the hair lifted or hold the hair between the fingers
to lift it and cut it to desired length. Always work from the back of the head.
Hair can be cut shorter gradually by reducing the space between the
comb/fingers, and the head.
Comb out trimmed hair and check for uneven strands.
(See diagram 5&6)
BLADE REMOVAL AND CLEANING
Short Tapered, Flat Tops and Short Cuts Hairstyle
• Starting with the longest attachment comb (12mm), cut from the back of the
neck to the crown. Hold the attachment comb flat against the head and slowly
move the clipper through the hair .
(See diagram 8)
• Use the same procedure from the lower side
to the upper side of the head. Cut the hair against
the direction in which it grows from the front to the
crown and then level the cut with the sides.
• To give a 'flat top' look, the hair on top of the head must
be cutover the top of a flat comb instead of using the
attachment comb.
• Use closer cutting attachment combs to taper the hair
down to the neckline as desired.Comb hair and check for
uneven areas and outlining sideboards and neckline as
described previously.

1.Fully charge the trimmer before you use it for the first time or afternot using
it for a long period ( When charging, please use a power adapter with an input
voltage not higher than 5V 1A).
2.Cleaning
It is not necessary to clean the cutter head frequently. It just needs a brush to
clean the excess hair for daily care.Since the body is not waterproof, please
remove the cutter head and clean it separately.
3. When the trimmer is used for 2 hours totally, some problems may occur,
such as relatively loud noise, dullness, dropping in shear force or high
temperature, then the cutter head needs dripping care. It is recommended to
replace the cutter head once a year.
4. When the product works continuously for about 40 minutes, the temperature
will generally rise. Please turn off the trimmer and restart after it cools down.
If the body temperature is abnormally high, please stop using it immediately
and cool it down for a while before restarting. If the heat persists,
please contact customer service.
5. To maximize battery life trimmer should be shut off immediately after using.
6.Do not allow children to use this product or treat it as a toy.
7. Do not use attachments not recommended by the manufacturer.
Be sure to check carefully before using the product. If there is any
damage, please stop using it.
8. Please use, charge and store this product at a temperature
between 󾙓󾙗󾙕󾙒
From the date of purchase, the main part of the product can enjoy a one-year
warranty service (excluding accessories).
Product failures due to accidental damage, unauthorized repairs, improper
storage and other man-made damage are not covered by the warranty.
After-sales Service: If you have any query about our products,
please feel free to contact us. Issues Contact Info:
WARM TIPS: WARRANTY
AND
SERVICE
Amazon Returns
or
Replace Item
Amazon
Customer Service
Social Medias
Official Website
SUPRENT
After-sales Service [e-mail]
www.suprent.com
Faceboo: @suprentinfo
Instagram: @suprent_official
8

HAIR CLIPPER HC315