SureCall Fusion5s 2.0 Omni/Dome User manual

All-Carrier Five-Band Signal Boosters for Large Home/Small Office
User Guide
Fusion5S 2.0
™

2
INTRODUCTION
Thank you for purchasing SureCall’s Fusion5s 2.0 cellular signal booster kit. Fusion5s 2.0 was
specically designed to eliminate frustrations over dropped calls, limited range and slow data rates
by amplifying incoming and outgoing cellular signals in homes up to 10,000 square feet.
The Fusion5s provides enhanced cellular signals for multi-carrier voice and data reception.
If you have any questions while assembling this kit please contact tech support at
Call: 1-855-846-2654
Email: [email protected]
Or, visit:
IntroductIon
https://www.signalbooster.com
» 1-855-846-2654 » https://www.signalbooster.com » [email protected]

Coax Cable
Outside Antenna
Booster
Inside Antenna
3
HOW IT WORKS
SureCall’s Fusion5s 2.0 is a high-quality bidirectional signal booster that enhances cellular signals to
areas that are prone to weak cellular coverage.
Fusion5s 2.0 works with two types of antennas: An inside antenna that communicates with your cell
phone and an outside antenna that communicates with the cell tower.
1. One outside antenna is used to collect signal from the cell tower.
2. The antenna then sends the signal to the booster through coax cable.
3. The booster amplies the cell signal and rebroadcasts the signal indoors via the inside antenna
or antennas to all mobile devices within range.
4. The system also works in reverse amplifying outgoing signal back to the tower.
How It works
» 1-855-846-2654 » https://www.signalbooster.com » [email protected]

TABLE OF CONTENTS
INTRODUCTION ..............................................................................................................2
HOW IT WORKS...............................................................................................................3
PACKAGE CONTENTS ....................................................................................................5
BEFORE INSTALLATION .................................................................................................7
Installation Overview....................................................................................................7
INSTALLATION.................................................................................................................8
Step 1. Find the area with the Strongest Signal ..........................................................8
Step 2. Install the Outdoor Antenna.............................................................................9
Option A: Outdoor Omni Antenna .......................................................................9
Option B: Outdoor Yagi Antenna ......................................................................11
Step 3. Install Indoor Antenna(s) .............................................................................. 12
Option A: Indoor Dome Antenna(s) .................................................................. 13
Option B: Panel Antenna ..................................................................................13
Step 4. Install the Signal Booster.............................................................................. 14
Booster Hardware.............................................................................................14
LED INDICATORS..........................................................................................................15
LED Information......................................................................................................... 15
TROUBLESHOOTING....................................................................................................15
If you Want to Improve Coverage ..............................................................................16
SPECIFICATIONS ..........................................................................................................16
Kitting Information .....................................................................................................17
CONSUMER GUIDELINES.............................................................................................18
WARRANTY....................................................................................................................19
Three-Year Product Warranty ...........................................................................19
4
table of contents
» 1-855-846-2654 » https://www.signalbooster.com » [email protected]

5
PACKAGE CONTENTS
1. Unpack all package contents. For missing or damaged items, contact your reseller.
2. Turn over the signal booster and record the model and serial number for reference:
Serial #: _____________________________________________________________________________
Purchase Date: _______________________________________________________________________
3. Keep the carton and packing material to store the product in case you need to return it.
Standard Fusion5s 2.0 signal booster packages include the following items:
• SureCall Fusion5s 2.0 booster and power supply
• One outside antenna (Omni or Yagi)
• One outside cable (75 ft)
• One or two inside antennas (depending on your kit; Omni dome or panel)
• Inside cable (30 ft.; one cable per inside antenna)
• plus 1 cable splitter (for multi-antenna kits)
Dome(s)
Fusion5s 2.0
Booster Outside Antenna (options)
Outside Cable Inside Antenna (options)
75 ft cable – SC-400
Inside Cable
Omni Yagi
Panel(s)
Splitter (for multiple antenna kits)
30 ft cable – SC-400
Package contents
» 1-855-846-2654 » https://www.signalbooster.com » [email protected]

6
Warning : Unauthorized antennas, cables, and/or coupling devices are prohibited by FCC rules. Please contact the FCC for details:
1-888-CALL-FCC. Changes or modications not expressly approved by SureCall could void the user’s authority to operate
the equipment.
Note: Fusion5s 2.0 is available in six kits
Outside
Antenna
Type
Outside
Cable
Length
Inside Antenna Inside Cable
Model number Model name (Qty) Type (Qty) Length Splitter &
cable
SC-PolysH/O-72-OD-Kit
Fusion5s 2.0 Omni / Dome Omni 75 ft (1) Dome (1) 30 ft -
SC-PolysH/O-72-OP-KIT
Fusion5s 2.0 Omni / Panel Omni 75 ft (1) Panel (1) 30 ft -
SC-PolysH/O-72-YD-KIT
Fusion5s 2.0 Yagi / Dome Yagi 75 ft (1) Dome (1) 30 ft -
SC-PolysH/O-72-YP-KIT
Fusion5s 2.0 Yagi / Panel Yagi 75 ft (1) Panel (1) 30 ft -
SC-PolysH/O-72-YD2-Kit
Fusion5s 2.0 Yagi / 2-Dome Yagi 75 ft (2) Dome (2) 30 ft 1
SC-PolysH/O-72-YP2-Kit
Fusion5s 2.0 Yagi / 2-Panel Yagi 75 ft (2) Panel (2) 30 ft 1
Fusion 5s 2.0 kits use the following antenna options based on environmental and coverage
requirements..
Antenna Type Model No. Usage Coverage
Outside Antenna Options
Outdoor omni-
directional
antenna
2-3 dBi / 3-4 dBi
SC-288W Omni antennas are the ideal solution
for sending/receiving signal from all
directions.
Outdoor
directional Yagi
antenna
8 dBi
SC-230W The Yagi antenna is a higher gain solution
ideal for low signal locations where the
antenna can be aimed to your closest
tower.
Inside Antenna Options
Indoor omni-
directional dome
antenna
2 dBi / 5 dBi
SC-222W The dome antenna, generally ceiling-
mounted, is omni-directional, sending/
receiving signal in all directions indoors.
Indoor directional
panel antenna
7 dBi / 10 dBi
SC-248W The panel antenna, generally wall-
mounted, provide directional indoor
coverage.
H. beamwidth: 120°; V beamwidth: 100°
table of contents
» 1-855-846-2654 » https://www.signalbooster.com » [email protected]

7
BEFORE INSTALLATION
• Prior to securing the location of any booster parts, a “soft install” is recommended as adjustments
may be needed to optimize performance.
• Make sure you have sufcient separation between outdoor antenna and indoor antennas. At least
50 ft. is recommended for best performance.
• Ensure sufcient cable length between the outside antenna location and
booster location. The length of the provided cable is 75 ft.
• For kits that use directional antennas (outside or inside), the directional
antenna(s) should be oriented in a way that do not “face” the other antenna
(see “Antenna Aiming” Diagram).
Installation Overview
Step 1. Find the outside area that has the strongest signal.
Step 2. Install the outdoor antenna in the area identied in step 1.
Step 3. Install the indoor antenna(s) where signal is needed.
Step 4. Place the booster in appropriate location and route cables from outdoor and indoor antennas
to the booster.
Step 5. Connect cables to the booster and nally, the booster to an AC power source.
Check System and optimize Installation, if needed
Aiming Directional
Antennas
OK
Outdoor/ Indoor Antenna Separation
A minimum of 50 ft. of separation between
the outdoor antenna and indoor antennas is
recommended for best performance.
Reducing antenna separation will reduce the
coverage provided by the booster and generally,
additional separation will provide better
performance.
An
t
enna Separat
i
on
Required distance between
indoor & outdoor antennas
Antenna Separation
before InstallatIon
Inside Antenna
Coax Cables
Cable Splitter
Signal Booster
Inside Antenna
Outside Antenna
» 1-855-846-2654 » https://www.signalbooster.com » [email protected]

8
INSTALLATION
Step 1. Find the area with the Strongest Signal
Using your phone, identify the outside location with the strongest signal for placement of your
outside antenna. Generally, this is found above the rooine on the side facing your nearest cell tower
and as high as possible – where the antenna can ‘see’ your cell tower. To nd the location of your
carrier’s closest cell tower, go to antennasearch.com.
The coverage area that the booster provides is directly related to the strength of incoming signal
received by the outdoor antenna. Mounting the outside antenna where the signal is the strongest
will provide the best results. Please note, if signal is extremely weak where the outside antenna is
installed, indoor coverage will be limited.
Note that Bars are not always a reliable measure of signal. The best way to conrm signal coverage
is the ability to place and hold a call.
Signal Strength
Excellent
-50 dB -60 dB -70 dB -80 dB -90 dB -100 dB
GoodPoor
Ins tal l atIo n
1-855-846-2654 I https://www.signalbooster.com/pages/contact-us I [email protected]
» 1-855-846-2654 » https://www.signalbooster.com » [email protected]

9
Step 2. Install the Outdoor Antenna
After identifying the area of strongest signal, choose the surface where you will mount your outside
antenna.
The location should allow for sucient separation between the outside antenna and inside antennas. The
minimum separating distance recommended for this booster is 50 Ft. Vertical separation is preferred as it
is more eective than horizontal separation. See “Antenna Separation” on page 7.
The location should allow for sufcient separation between the outside antenna and inside antenna.
Vertical separation is preferred as it is more effective than horizontal separation.
The minimum separating distance recommended is 50 feet; however, increased separation,
especially where vertical separation cannot be achieved.
IMPORTANT: Do not collocate antennas or operate the outdoor antenna with any other antenna or signal booster.
Option B:
Yagi Antenna
Option A:
Omni Antenna
Option A: Outdoor Omni Antenna
The omni antenna is omni-directional, which receives and sends signals in a 360º radius. The
provided hardware allow for either a surface mount or pole-mount.
For best performance, be sure to place the outdoor antenna at least 50 feet from the indoor
antennas. Place the antenna as high as possible. Make sure that the mounting area has at least a
36-inch radius clear of obstructions and other radiating elements. The antenna should be mounted in
an upright position. See illustration.
A
nt
e
nn
a
S
epar
a
ti
on
Required distance between
indoor & outdoor antennas
Outdoor/ Indoor Antenna Separation
A minimum of 50 ft. of separation
between the outdoor antenna and
indoor antennas is recommended for
best performance.
Reducing antenna separation will
reduce the coverage provided by
the booster and generally, additional
separation will provide better
performance.
Ins tal l atIo n
» 1-855-846-2654 » https://www.signalbooster.com » [email protected]

10
Planned
booster
location
Outdoor
Cable
Outdoor Omni
To mount antenna to a vertical surface:
1. Using vertical plate of L-bracket, mark position of desired placement.
2. Place vertical L-bracket into desired location and tap the screws, head rst, along with sleeve,
into stucco 1/2 to 5/8 inches deep into place. (Note: Alternate screws may be required for
different surfaces such as wood or concrete.)
3. In this order, place washer, lock washer and nut on each screw and tighten until secure. When
tightening screw, sleeve will expand to secure plate.
4. Use provided screws to secure antenna base onto horizontal plate.
5. Connect antenna to cable connector for the outdoor cable provided with your kit and run along
route to planned location of your booster.
Mast
(not provided)
Cable
L-Bracket U-Bolts
Washers
Nuts
Cable
Anchors /
Sleeves
Screws Washers
Nuts
L-Bracket
Mast
(not provided)
Cable
L-Bracket
U-Bolts
Washers
Nuts
Cable
Anchors /
Sleeves
Screws Washers
Nuts
L-Bracket
Surface Mount
Pole Mount
Pole-mount
hardware
Omni antenna with
surface mount
hardware
Ins tal l atIo n
» 1-855-846-2654 » https://www.signalbooster.com » [email protected]