Suresafe SH-055DV User manual

Besides, you also can detect by earphone hearing
without others awareness.
This model also has VIBRATE detection to warn you
when you do not hold this device in hand to scan an
environment.
SH-055DV:
SH-055DV
Sound
Vibrate
Off
SILENT DETECTION
LOW BATTERY WARNING
When the detector is switched on and the LED in the
bottom with a battery icon is Red, it means the batteries
run down. Please replace new batteries.
Thank you for purchasing the Suresafe RF (Radio
Frequency) Signal Detector. Please first read over this
manual for proper use, save this manual and keep it
handy.
This device applies with fuzzy scanning technology to
detect peeping cameras, bug, cellular phones and
other radio frequency devices. This device surely
avoids being peeped or tapped to protect privacy or
protect information being disclosed secretly.
This device has a new digital amplifier to heighten the
indication for the digital signals of Bluetooth, WLAN,
Wi-Fi, cellular phone and Digital Spread Spectrum
wireless products, etc.
This device has 3 LEDs indicating the detected
signal strength. When detecting cellular phone or
peeping camera, the LED will light from Level 1 to
Level 2 to Level 3, and the beeping sound will
change from Slow to Rapid indicating the strength
of detected signal.
User's Manual
SH-055DV
with Analog / Digital select switch
Exposing Spy Camera, Bug and Cellular Phone and Bluetooth, etc.
High sensitivity
RF Signal Detector
WARNING
Use this device as an auxiliary, supplemental help or aid to prevent the risks
caused by hidden camera, cellular phone or other wireless devices. This device
does not take the place of all the supervisions. Performance of this Radio
frequency (RF) product will be affected by the circumstance of use. The
producer and marketing group accepts no liability for any loss or damage by
malfunction or misuse.
55DVPK1A
09.2010
COPYRIGHT
No part of this manual may be reproduced, transmitted, transcribed, or
translated into any language in any form by any means, electrical or mechani-
cal, including photocopying, recording, or information and retrieval systems,
without the express written permission of manufacturer. Products mentioned in
this manual are for identification purposes only. All brand names appearing in
this manual may or may not be registered trademarks or copyrights of their
respective companies. The manufacturer reserves the right to change or modify
the specifications of any one or all of these products as deemed necessary at
any time without prior notification. The manufacturer may further revise this
manual from time to time without prior notice.
Copyright 2001-2010, Patent pending, All rights reserved.
Suresafe , Pro Hunter are trademark of the manufacturer.
Made in Taiwan.
™ ™
* Specifications may change without notice
SPECIFICATION
Power
Detecting frequencies
Dimension
Weight
Warning mode 1
Warning mode 2
Warning mode 3
Detecting Distance:
5.8GHz Wireless camera
2.4GHz Wireless camera
2G Cellular phone (1)
2G Cellular phone (2)
AAA/UM-4 battery x 2, 3V DC
50 MHz - 6.0 GHz
L 87 x W 55 x H 24 mm
70 g
Audible alarm and 3 LEDs
Vibration and 3 LEDs
Silent, 3 LEDs and earphone hearing
about 2feet (regular 10mW camera)
about 8feet (regular 10mW camera)
about 20 feet (set at Analog)
about 30 feet (set at Digital)

Turn the sensitivity tuner to - (minus) side to decrease
the sensitivity and the detecting distance will be
shorter. Turn the sensitivity tuner to + (plus) side to
increase the sensitivity and the detecting distance will
be longer.
SENSITIVITY ADJUSTMENT
INTERFERENCE (BACKGROUND NOISE)
ELIMINATION
1.The sensitivity tuner is also used to eliminate the
background noise (interference).
2.If the scan environment has other noises that
interfere with your detector, the strength indication
LED will light up.
3.If this condition appears, adjust the sensitivity by
turning the sensitivity tuner to - (minus) side to
decrease the sensitivity until the Level 1 Yellow
LED slightly lights up.
4.In normal condition, when turning on the power, only
the power LED goes Green to confirm the detector
is in normal condition.
HOW TO OPERATE
1.Slide and remove the battery lid, install two
AAA/UM-4 batteries matching correct (+) and (-)
poles as indicated, then slide the battery lid back.
2.Pull out the antenna and turn on the switch to upper
side.
3.The power LED will go Green to confirm the
detector is operated correctly.
4.Before scanning an environment, please first set up
the sensitivity benchmark. Turn the sensitivity tuner
to + (plus) side until the Level 1 LED goes Yellow,
then turn the sensitivity tuner to - (minus) side to
decrease the sensitivity until the Level 1 LED goes
slightly Yellow.
5.When you switch on this device and the strength
LEDs light up, it means the detecting benchmark is
too sensitive. Turn the sensitivity tuner to - (minus)
side to decrease the sensitivity until the Level 1
LED goes slightly Yellow.
6.When this device detects signal of cellular phone or
wireless camera, the strength LED will light up,
from Level 1 (Yellow) -> Level 2 (Yellow) -> Level 3
(Red ) indicating the strength of detected signals.
7.Meanwhile, the buzzer will be beeping and the
sound will be changing from slow to rapid,
indicating the strength of detected signals.
1.If you are not going to use this device for a long
time, remove the batteries to avoid damage caused
by corrosion from battery leakage.
2.Unauthorized repair or dismantle of this device will
void all the warranties.
NOTICE OF USE
The signal waves of wireless camera and hidden
microphone is continuous wave, so the LED of the
detector will light up without blinking when the detector
detects a wireless camera or hidden microphone. And
the buzzer will go off continuously.
The signal waves of cellular phone is pulse wave, so
the LED of the detector will be blinking when the
detector detects someone uses cellular phone. And the
buzzer will go off discontinuously and small sound.
HOW TO DISTINGUISH IF IT IS A SIGNAL
OF WIRELESS CAMERA OR HIDDEN
MICROPHONE OR CELLULAR PHONE?
The signal of wireless camera, hidden microphone and
walki talki (2-way radio) are analog signal. The signal of
Bluetooth, WLAN, Wi-Fi, cellular phone and digital
spread spectrum products are digital signal.
Usually, set the A-D switch to A. When to detect analog
signals, the LED of the detector will light up without
blinking and the buzzer will go off continuously.
When to detect digital signals, the LED of the detector
will be blinking and the buzzer will go off dis-
continuously and small sound. Set the A-D switch to D,
it will have stronger indication for the digital signals of
Bluetooth, WLAN, cellular phone and Digital Spread
Spectrum wireless products, etc.
ANALOG / DIGITAL SELECT SWITCH
3.Avoid water.
4.Do not store this device in an excessively hot place.
5.Avoid knocks or dropping this device.
6.Never use the antenna of this device to touch a metal
surface or the antenna of signal emission source. The
quality warranty does not include the damage caused
by static electricity or feedback.