Suttle FutureLink 649NV-48 User manual

Suttle
Part Number
Product Information
Description
649NV-48 1-line VDSL2 NID splitter, RJ14 test jack (pair 1 = network, pair 2 = premise), 3 x single-pair tool-less toggles
for voice, 1 x single-pair tool-less toggle for data (purple)
649NV-CONVKT Conversion ground bar and adapter cradle used to install 649NV-48 & protection module in Siecor NI-2006-
13L11CT, NI-2006-13L
649-ADP Adapter cradle and auxilliary clip used in Siecor NI-2006-13L11CT, NI-2006-13L to install 649-NV-48
649NV-48
649-ADP
649NV-CONVKT
The FutureLinkTM VDSL NID splitter is designed to provide POTS
separately from VDSL signals at the point of entry to a subscriber.
The Ring Trip Mitigation feature allows uninterrupted IPTV
services during phone calls. Its unique tool-less technology is
designed to fit inside most NIDs.
A toggle design allows three pair tool-less voice distribution
and one pair tool-less data distribution. Clear toggles allow the
installer to clearly see that the connection has been established.
The splitter supports all ADSL and VDSL2 technologies up to 30
MHz (30a Profile).
DC Loop Current: 0 – 100mA
DC Loop Voltage: 0 to -60V
DC Resistance: ≤ 25 Ω
Insertion Loss: < 0.5dB
Attenuation Distortion: < 1.0dB
Delay Distortion: < 200us
ADSL Band Attenuation: > 65dB @ 30kHz – 300kHz
> 55dB @ 300kHz – 30MHz
Return Loss:
6dB ERL, 5dB SRL-Low, 3dB SRL-High
Longitudinal Balance: > 57dB
Lead Wire Length: 12 inches
■ Tool-less capability with easy viewing for proper connections
■Front facing IDC wire entry holes for ease of insertion
■Accepts 22-26 AWG wire
■Minimal termination force required for each wire pair
■Audible click toggle upon installation
■ Convenient mounting for most NID styles
■ Ring Trip Mitigation for superior IPTV delivery
■
Cradle detaches and allows placement on premise walls separate from NID
■ Compatible for ADSL to VDSL2 technologies up to 30MHz (30a profile)
Compatible with a variety of NIDs including:
Corning: 7600 Series, 9600 Series, UNI-3056-11U2,
UNI-30EQ3-13U1, UNI-30K3, UNI-30K6,
NI-2006-13L11CT, UNI-30C3-13U1, UNI-30C6-13U1
Tyco-Keptel: SNI4600
AFL: SNI-760
Siecor: NI-2006-13L11CT, NI-2006-13L
FutureLinkTM Tool-less VDSL NID Splitter
Specifications
Description
Features
TR-127 (Ring Trip Mitigation): Approved
GR-3167: Compliant
FCC: Approved
Testing
649NV-48
649-ADP

1001 East Highway 212 • Hector, MN USA 55342 • suttlesolutions.com
Toll Free: 1 [phone] • Local: [phone] • Fax: [phone]
Specifications subject to change without notice. Copyright 2014. 1120514
FutureLinkTM Tool-less VDSL NID Splitter
The cradle comes attached to the splitter in shipping.
First, make sure the network leads out of the splitter are facing the
TELCO side of the NID.
Second, tilt the attached splitter and cradle down towards the right
side of the NID slot and rock the left side down into position.
The cradle comes attached to the splitter in shipping.
First, detach the cradle from the splitter by pulling back on the
cradle arm from the splitter.
Second, tilt the splitter down to the right so that the tab beneath
the splitter slides under the knob fixed on the NID.
Lastly, push the left side of the splitter down while snapping the
NID arm tab into a latching position with the splitter.
■ Remove cradle from module.
■ The cradle may be attached to a premise backboard with two
flathead screws. Attach the cradle close to the 66 block so that
the 12” tail from the module can reach.
■ Snap the module into the cradle and attach the network leads
to the connector block for the Telco feed.
■ Data and voice jumpers can be run from the module to the
proper distribution connections.
To view a demonstration video, visit the Suttle website
(www.suttleonline.com) and select the video area under the
support tab.
If you need additional training please call Customer Service at
1-800-852-8662.
Premise Application
Mounting Instructions (with cradle)
Mounting Instructions (without cradle)
■ Install 649NV module, terminate all network and premise
connections.
■ Use a test set with a 6 position, 4 conductor RJ plug.
■ Open cover, disconnecting network input, and insert test set
into the “TEST” jack.
■ Test the line for shorts or opens using L1 (center pair of RJ
contacts).
■ Test the bridged POTS drops (up to 3 premise connections)
for shorts using L2 (outer pair of RJ contacts).
■ To test for open circuits in the bridged POTS drops; close
the 649NV module cover completely, plug test set into user
interface jacks in the premise.
■ To test for shorts or opens on the data port; close the 649NV
module cover completely, plug test set into use interface jack
in the premise.
Testing Procedure
Application Diagrams