Suzuki HDP User manual

IF YOU HAVE ANY QUESTIONS OR PROBLEMS,
CALL THIS TOLL FREE HELP LINE.
STOP!
DO NOT ASSEMBLE YOUR PIANO
BEFORE READING THIS GUIDE!
1•8OO•854•1594
Easy
Assembly
Guide
The Name You Know
Suzuki Home Digital Piano
ATTENTION!
Use these instructions for Piano Assembly.

E6
E1
E3
E2
E4
E7
E5
D1
D2
D3
D4 D4
D5 D6
1. Un pa c k i n g Yo U r ne w Digital pi a n o
2. at t a c h i n g St a n D le g S t o pe D a l Bo a r D
D. Parts enclosed: E. Hardware enclosed:
E1. Four (4) 3/4" Machine Screws
E2. Four (4) 1/2" Machine Screws
E3. Two (2) 1/2" Machine Screws
E4. Four (4) 1/2" Wood Screws
E5. Phillips Screw Driver
E6. Bendable Wire Holders
with Screws (Pedal Wire)
E7. Headphone Holder and
Screws
D1. Piano
D2. Pedal Board
D3. Privacy Board
D4. Two (2) Stand Legs
D5. Power Cord
D6. Hardware and Phillips
Screw Driver
A. Carefully unpack the Piano
components and set aside.
IMPORTANT!
Be sure to unpack the Hardware
and Power Supply from the
protective foam pieces.
B. Using 2 people, lift your new
Piano out of the carton and place
on a soft surface such as a carpet
or blanket.
C. Remove the protective outer packing
materials from the Piano.
IMPORTANT!
Use only your hands to remove the protective
materials. Sharp tools may damage the piano.
The finish of your Piano is now exposed.
Take care not to let foreign objects come into
contact with the Piano.
A. Slide the Pedal
Board over the "L"
Bracket on the bottom
of the Stand Leg and
align the holes.
B. Attach the Pedal
Board to the Stand
Legs using four 3/4"
Machine Screws (E1).
"L" Bracket
Pedal Board

(Continued)
3. at ta c h i n g t h e pr i v a c Y Bo a r D
3. at ta c h i n g t h e pr i v a c Y Bo a r D
A. Align the Privacy Board to the backside
of the Leg Stands.
B. Align the holes in the Privacy Board with the Threaded
Holes of the Leg Bracket. Install using two 1/2" Machine Screws
(E3) into the Privacy Board.
IMPORTANT!
Do not tighten them at this time.
C. Align the 4 small holes at the bottom of the Privacy
Board with the holes in the Pedal Board. Install
four 1/2” Wood Screws (E4) prior to tightening them.
IMPORTANT!
Do not over tighten the screws.
4. at t a c h i n g t h e pi a n o
t o t h e St a n D
A. Using two people, lift the Piano onto the Leg Stands
and Pedal Board assembly.

Questions?
Call 1•800•854•1594
4. at t a c h i n g t h e pi a n o t o t h e St a n D
en j o Y Yo U r ne w SU z U k i Digital pi a n o !
© 2007 Suzuki Corporation
The Name You Know
C. Locate the Power Cord
and plug it into the Receptacle
on the bottom of the Piano.
Plug the Power Cord into an
appropriate wall socket.
D. Refer to the Owner’s
Manual for piano operation.
Stand
Positioning
Pin
5. co n n e c t i o n S & po w e r
Power
Receptacle BACK
FRONT
Connection
Jacks
Stand
Positioning
Pin
Headphone
Jacks
Holes for Optional
Headphone Clip
A. Piano Bottom Attachments and Connections.
B. Slide the Piano onto the Stand
so the Position Pin is in the Slot of
the Rear Stand Bracket.
C. Align the Bracket Holes
with the Threaded Inserts.
D. Secure the Piano to
the Stand using four 1/2"
Machine Screws (E2).
Rear Stand
Bracket
Piano Bottom
Piano Stand
Position Pin
Bracket
Holes
(continued)
B. Place the piano in its final position then turn the
Pedal Brace Knob down to the firmly touch the floor.
Check and tigthen all screws at this time.