Swann Advanced Quad Processor User manual

1
Doorphone
Video Intercom
Colour Camera with 3.5” LCD Screen
MDP870C210113E
Advanced-Series

2
Package Contents
LCD SCREEN: This is where you view your visitor that the outdoor camera sees.
MONITOR: Press this button to connect to the camera and view what the outdoor
camera sees.
UNLOCK: If you have attached an electronic door unit to the Doorphone, you can
unlock the door by pressing this button.
TALK: Press the TALK button to speak to the visitor. You don’t need to hold down the
button as the Doorphone communicates with the outdoor camera for one minute. If
you need to speak for longer, press the TALK button again.
MICROPHONE: Speak into the microphone to communicate with the visitor.
SPEAKER: This is where you hear the visitor speak to you from the outdoor camera.
*Note: Please remove the protective plastic from the Doorphone before installation.
Layout
What’s in the box:
• 3.5” LCD monitor
• Outdoor camera
• Power adapter
• Cable 50ft/15m
• Mounting screws, brackets & plugs
• Operating instructions
Monitor
3.5” LCD Screen
Unlock
Talk
MicrophoneSpeaker

3
Layout
MICROPHONE: This is where the visitors
speak to you.
CAMERA LENS: This is where the image of
the visitor is captured.
INFRARED LIGHT: The infrared light is what
allows the camera to see visitors at night.
The image will appear in black and white.
CALL BUTTON (DOORBELL): When the
visitor presses this button, the doorbell will
ring and the Doorphone will display the
image from the camera.
SPEAKER: This is where the visitor hears you
speak to them from the Doorphone.
The left side of the Doorphone has extra controls that you can adjust.
MELODY SELECTION: There is a wide variety of dierent melodies that you can
select from. Press this button to select a dierent melody.
BRIGHTNESS: This adjusts the brightness of the image seen on the Doorphone.
COLOUR: This adjusts the colour level of the image seen on the Doorphone.
VOLUME: This adjusts the volume level of the speaker.
WIRING TERMINAL: This is where the enclosed cable is connected to.
DC 12V: This is where you plug the power adapter.
Microphone
Camera lens
Infrared light
Call button
(Doorbell)
Speaker
Melody Selection
Brightness Control
Colour Control
Volume Control
Wiring Terminal
DC12V

4
The ideal installation height of the
Doorphone is about 4.7ft-5.2ft /
145-160cm from the ground.
We recommended you drill a hole in the
wall and to insert the cable before you
screw the mounting bracket on. Connect
the provided cable and power adapter to
the rear of the Doorphone (see page 5).
To mount the Doorphone, use the two
screws to secure the mounting bracket to
the wall. Make sure the four metal hooks
are pointing up. Place the Doorphone
onto the mounting plate, lining up the
four hooks with the grooves in the back of
the Doorphone.Then slide the Doorphone
down to secure it onto the hooks.
To mount the outdoor camera run the
cable from the Doorphone and pull it
through the hole you created at the
camera mounting point, and then use
the four screws to secure the mounting
bracket to the wall with the wire inside the
bracket so you can connect the camera.
Attach the cable to the rear of the outdoor
camera as shown in the wiring diagram
(see page 5). Use a small screwdriver to
push in the small button atop each wire
terminal, and then insert the wire. Place
the outdoor camera onto the mounting
bracket and slide it in top-edge rst to
ensure the notches t into the guide holes
at the top of the bracket.
To nish, secure the outdoor camera to
the mounting bracket by inserting the
screw through the bottom of the bracket
which holds it in place. Cover the hole
with the provided silicon cap.
Doorphone Installation
1.64ft / 50cm
5.9ft / 180cm
3.6ft / 110cm
4.7ft - 5.2ft / 145 - 160cm
2.48 inches / 63mm
Outdoor Camera Installation

5
wiring diagram
DISTANCE: The recommended distance between the Doorphone and the outdoor
camera is approximately 50ft/15m as per the supplied cable. It is possible to use a
longer cable, however environmental conditions and the quality of the cable used
can aect operation and the maximum reliable distance you can achieve.
CONNECTION: To ensure everything works correctly, we advise you connect
the Doorphone and outdoor camera together before installation to check you
understand the wiring and that everything works as it should.
Caution
• Keep the Doorphone device away from water or moisture and dusty areas. Avoid
environments where the Doorphone will be exposed to direct sunlight.
• Keep the Doorphone device away from devices with strong magnetic elds such
as televisions.
• Do not drop the Doorphone as it may cause damage and may void the warranty.
• Do not use solvents or detergents to clean the Doorphone. To clean, lightly
moisten a cloth with water and wipe down the device.
• Do not disassemble the unit for any reason. If the unit fails, please refer to the
back page for contact details.
Wiring diagram
WARNING: When tting the screws into the wall, make sure you are
not inserting those anywhere near electrical wires, including wires
that may be behind the wall. If you are unsure at all, please get a
professional to check rst and install the screws for you.
!
1. Audio wire
2. Ground wire
3. Video wire
4. Power wire
Doorphone
Electronic
Lock
Outdoor Camera
Blue
Brown
Green
Black
*Note - The colour indication is only a guide. Make sure that the same coloured wire is attached to the
same terminal on each device, for example - blue wire connects to terminal one on the Doorphone,
also connects to terminal one on the outdoor camera. An additional Doorphone can also be connected
so you can view the video feed from another room. Make sure that the same coloured wire is attached to
the same terminal on the additional Doorphone.
Attach the cable to the rear of
the Doorphone by sliding the
U-shaped connection under
each screw terminal. Screw
into place and be careful not
to over tighten.

6
DOORBELL: The visitor presses the call
button to ring the doorbell. A video
feed will appear on the Doorphone.
MONITOR: When in STANDBY mode, touch
and release the MONITOR button to view
a video feed from the camera. The video
feed will switch o automatically after one
minute or you can touch the MONITOR
button again to switch o the video feed.
If it is too dark outside like at night, the image
on the Doorphone will appear black and white.
TALK: Touch and release the TALK button
to talk to the visitor. Press the TALK button
again to switch o the video feed.
UNLOCK: If the “electronic lock” option is
tted, press the UNLOCK button to unlock
the door for the visitor, the door stays
unlocked as long as the button is pressed.
NOTE: You will need an external door lock
connected.
Operation

7
Troubleshooting
DOORPHONE
Operating Power:
Resolution:
Display size:
Cut-o time:
Operating temperature:
External Dimensions:
OUTDOOR CAMERA
Power supply:
Viewing angle:
Lighting source:
Night vision distance:
Operating temperature:
External dimension:
DC 12V
320 x 240
3.5” LCD
1 minute (before unit enters standby from call/monitor)
-10°c ~ +40°c / -4°F ~ 122°F
160mm x 103mm x 22mm / 6.2” x 4.0” x .8”
(supplied by Doorphone)
65° for the pinhole camera
Infrared LED
13ft / 4m
-20°c ~ +50°c / -4°F ~ 122°F
130mm x 51mm x 47mm / 5.11” x 2” x 1.85”
No sound or hard to hear the visitor:
If you are nding it hard to hear the visitor, adjust the volume on the side of the
Doorphone to make it louder. If this is not sucient, ask the visitor to stand closer to
the outdoor camera unit when speaking.
If the visitor is nding it hard to hear you, stand closer to the Doorphone unit when
speaking.
If you are still having diculties, check that everything is properly installed as per the
Installation and Wiring instructions.
The image is unclear or you cannot see the visitor:
Make sure there is nothing covering the lens on the outdoor camera.
If you are nding it hard to see your visitor, adjust the brightness or ask the visitor to
stand closer to the outdoor camera. The outdoor camera is quite good at displaying
people standing within a few meters of the device in darkness but if you are still
having problems, you may need to install an additional light to illuminate the area.
Make sure the wiring is attached as shown in the wiring diagram in this manual.
The door is not unlocked when you press the door unlock button:
Make sure the wiring to the door strike (door latch mechanism) is wired correctly and
that the wires are properly attached.
*Note: Please remove the protective plastic from the Doorphone before installation.

8
© Swann Communications 2013
Warranty Information
Helpdesk / Technical Support Details
Swann Technical Support
All Countries E-mail: [e-mail]
Telephone Helpdesk
See http://www.worldtimeserver.com for information on time zones and the
current time in Melbourne, Australia compared to your local time.
USA toll free
1-800-627-2799
(Su, 2pm-10pm US PT)
(M-Th, 6am-10pm US PT)
(F 6am-2pm US PT)
USA Exchange & Repairs
1-800-627-2799 (Option 1)
(M-F, 9am-5pm US PT)
AUSTRALIA toll free
1300 138 324
(M 9am-5pm AUS ET)
(Tu-F 1am-5pm AUS ET)
(Sa 1am-9am AUS ET)
NEW ZEALAND toll free
0800 479 266
UK
0203 027 0979
Swann Communications USA Inc.
12636 Clark Street
Santa Fe Springs CA 90670
USA
Swann Communications
Unit 13, 331 Ingles Street,
Port Melbourne Vic 3207
Swann Communications LTD.
Stag Gates House
63/64 The Avenue
SO171XS
United Kingdom
Swann Communications warrants this product against defects in workmanship and material for a period
of one (1) year from it’s original purchase date. You must present your receipt as proof of date of purchase
for warranty validation. Any unit which proves defective during the stated period will be repaired without
charge for parts or labour or replaced at the sole discretion of Swann. The end user is responsible for all
freight charges incurred to send the product to Swann’s repair centres. The end user is responsible for all
shipping costs incurred when shipping from and to any country other than the country of origin.
The warranty does not cover any incidental, accidental or consequential damages arising from the use of
or the inability to use this product. Any costs associated with the tting or removal of this product by a
tradesman or other person or any other costs associated with its use are the responsibility of the end user.
This warranty applies to the original purchaser of the product only and is not transferable to any third
party. Unauthorized end user or third party modications to any component or evidence of misuse or
abuse of the device will render all warranties void.
By law some countries do not allow limitations on certain exclusions in this warranty. Where applicable by
local laws, regulations and legal rights will take precedence.
FCC Verication
This equipment has been tested and found to comply with the limits for Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio or television reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
WARNING: Modications not approved by the party responsible for compliance could void user’s authority
to operate the equipment.