Swann SWPRO-A852PTZ User manual

Day & Night
PTZ Dome Camera
EN
For use with Swann 4400 Series HD DVRs
INSTRUCTION MANUAL

1
Congratulations on your purchase of this Day
& Night PTZ Dome Camera. A state-of-the-art
high resolution camera with 10x optical zoom.
The camera can pan a full 360 degrees and can
focus on key locations with multiple pre-set
viewing points. The 720p resolution is perfect
for close up detail such as license plates, facial
detail, and more. With the latest infrared cut fil-
ter, it has amazing night vision to 196ft/60m and
excellent clarity in low light. It’s ready to go with
a pre-installed mounting bracket.
Important note - All jurisdictions have specific
laws and regulations relating to the use of cam-
eras. Before using any camera for any purpose,
it is the buyer’s responsibility to be aware of all
applicable laws and regulations that prohibit or
limit the use of cameras and to comply with the
applicable laws and regulations.
Important safety instructions
1) Make sure the camera is fixed correctly and
stable if fastened in place.
2) Do not operate if wires and terminals are ex-
posed.
3) This camera can only be used in combination
with Swann’s DVR4-4400, DVR8-4400 or DVR16-
4400 digital video recorders.
4) Only use the supplied power adapter (24V).
5) Do not manually pan and tilt the camera when
it is turned on.
6) Use a small flat-head screwdriver to connect
the PTZ module that is attached to the rear of your
DVR, to the red and black PTZ wires on the video
& power cable.
Warning - Modifications not approved by the
party responsible for compliance could void us-
er’s authority to operate the equipment.
Introduction

2
Choosing a location for your PTZ Camera
With a PTZ camera, you have some flexibility on
where the camera can be mounted. Some things to
consider when choosing a location -
1) What you want to monitor and where you’ll get the
best view of it.
2) How you’re going to connect the camera to your
DVR; remember that cables and connections should
be kept out of the weather.
3) It’s recommended to mount your cameras at an
elevated position to keep out of harm’s way.
4) Make sure your camera has minimal sky in it as
the light in daylight can make the foreground of the
image darker.
5) Think about the most likely way a potential offender
may approach your home.
6) The camera’s casing is resistant to water and
tampering. However, the cable and connector are
vulnerable and require protection.
7) Prolonged exposure to adverse weather conditions
such as sunlight or excessive moisture, may
eventually damage the internal components of the
camera and adversely affect its performance.
8) When running your cable, try to avoid bending it at
sharp angles.
9) Don’t put your cable near live electrical wiring.
AC electricity generates radio “noise” which can
interfere with the signal from your camera.
10) As the camera can pan a full 360 degrees, this
means that (for example) installing it in a tight corner
is probably not an ideal utilization of its potential. A
freestanding pole of sufficient height and integrity
to reliably hold the camera securely is an ideal
choice, as is the centre of a wall in a larger room or
a warehouse.

3
Connecting your PTZ Camera
Power Input
Video Output
PTZ
1
Red
Black
Power Input
Video Output
Video Input
Power Output
PTZ
2
Video & Power Cable
13
Power Adapter
4
PTZ
75 3 1
86 4 2
eSATA
HDMI LAN & USB B A DC 12V
IN
VGAVIDEO IN AUDIO OUT
AUDIO IN
23

4
Connecting your PTZ Camera (cont.)
1) Connect the PTZ connection on the camera to
the PTZ connection on the video & power cable
(the connection is keyed so it connects in one
orientation). Connect the video output and power
input on the camera to the corresponding connec-
tions on the video & power cable.
2) Connect the video output on the video & power
cable to a spare video input on the DVR.
3) Disconnect the PTZ module on your DVR. Using
a flat-head screwdriver, attach the PTZ wires (red
& black) to the PTZ module. The red cable con-
nects to “A” and the black cable connects to “B”
(as illustrated). Ensure the wires are held firmly
then tighten (don’t use too much force). Recon-
nect the PTZ module to the DVR when finished.
4) Connect the power input on the video & power
cable to the provided power adapter. Connect the
power adapter to a spare power connection.
When the camera is turned on, it will initialise
a self-test then display some information about
itself on-screen -
S/N: 201504031002
VERSION : V1.22AN
MODEL : DOME
PROTOCOL : PELCO
DOME ID : 001
BAUDRATE : 9600
The DVR’s default PTZ settings should allow you
to use the camera without any configuration.
However, there are many options that can be ac-
cessed using the DVR’s menu as well as the on-
screen menu on the camera. Download our com-
prehensive user manual available at our website.

5
Mounting & controlling your PTZ Camera
The PTZ camera can be mounted onto a flat sur-
face using the supplied mounting hardware. Ma-
terials such as hardwood, brick or concrete are
good options, and we’ve included all the gear
you’ll need for mounting.
1) Position the camera in the location you want to
mount it. Make sure the location is rigid to prevent
vibration.
2) Using a pencil or felt tip maker, mark the 4
screw holes on the surface to position the screws.
3) Using the appropriate screws for the surface
you’re fixing the camera to, screw the camera into
place. Make sure the camera’s bracket is aligned
straight, otherwise the image on the DVR will ap-
pear on an angle.
4) For wooden surfaces, screw the camera direct-
ly to the surface. For masonry surfaces (bricks or
concrete) you’ll need to use the wall plug.
To control the PTZ camera, use the mouse and
click the channel the camera is connected to.
Click the “PTZ” button on the camera toolbar. Ap-
pearing on-screen is the PTZ controls –
1) Click the directional buttons to move the cam-
era in the direction selected.
2) This determines how fast the camera will move.
3) The ability to zoom into an object and to con-
trol the level of focus (the “Iris” controls are not
available).
1
23

6
Limited Warranty - Terms & Conditions
Swann Communications warrants this product
against defects in workmanship and material for
a period of one (1) year from its original purchase
date. You must present your receipt as proof of
purchase for warranty validation. Any unit which
proves defective during the stated period will
be repaired without charge for parts or labour
or replaced at the sole discretion of Swann. The
end user is responsible for all freight charges in-
curred to send the product to Swann’s repair cen-
tres. The end user is responsible for all shipping
costs incurred when shipping from and to any
country other than the country of origin.
The warranty does not cover any incidental, ac-
cidental or consequential damages arising from
the use of or the inability to use this product. Any
costs associated with the fitting or removal of this
product by a tradesman or other person or any
other costs associated with its use are the re-
sponsibility of the end user. This warranty applies
to the original purchaser of the product only and
is not transferable to any third party. Unauthor-
ized end user or third party modifications to any
component will render all warranties void. By law
some countries do not allow limitations on certain
exclusions in this warranty. Where applicable by
local laws, regulations and legal rights will take
precedence.
For Australia: Our goods come with guarantees
which cannot be excluded under Australian Con-
sumer Law. You are entitled to a replacement
or refund for a major failure and for compensa-
tion for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of ac-
ceptable quality.

7
FCC Verification
This equipment has been tested and found to comply with the limits for Class B digital device, pursu-
ant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected
• Consult the dealer or an experienced radio/TV technician for help
These devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) These devices may not cause harmful interference.
(2) These devices must accept any interference received, including interference that may cause unde-
sired operation.

MA852PTZ060515E | © Swann 2015
Helpdesk/Technical Support
Technical Support E-mail: [email protected]om
Telephone Helpdesk
USA Toll Free 1-800-627-2799
USA Parts & Warranty 1-800-627-2799
(M-F, 9am-5pm US PT)
AUSTRALIA 1800 788 210
NEW ZEALAND Toll Free 0800 479 266
UK 0808 168 9031