Swelight M15 User manual

Congratulations on your purchase!
Regards,
Stuff at Swelight and cartown.eu
INSTALLATION INSTRUCTION
MUSTANG 2015+
Swelight Flashlightconverter M15
Developed, constructed and manufactured in Sweden
v. 2016.7.13

2280A
Thank you for your purchase of the Swelight M15 light bulb converter for the Ford
Mustang 2015+ Thanks to the M15, you can easily modify the flash signal on your car.
You only need to complete with tools. Keep in mind that ALL joints must be soldered
and insulated. Cable joints, clamping sleeves, sugar bits or other joints should not be
used at all
M15 - How to do this:
1. Start by disassconnecting the minus pole from the car's starter battery so that the car
becomes powerless.
2. Remove the luggage compartment cover on the right side of the luggage compartment.
Then remove the metal bracket to which the BCM-B box is mounted. The BCM-B box is black
and about 15cm wide, 10cm deep and 2cm high. It has two connectors (black / gray). Lay
the box with the bracket aside and lay the rope frame so that it is easily accessible.
3. Cut the insulation a bit from the black connector so that approximately 10 cm of the cables
are exposed. TIP: When cutting cables near a connector, always leave 4-5cm cable to the
connector so that you can easily reset or change the connection.
4. Remember to cut the following cables approximately 4-5cm from the BLACK connector::
White / Green (Pol 2) (Cable Connector Isolated)
Brown / Purple (Pol 3) (Cable Connector Isolated)
Gray / Brown (Pol 4)
Blue (Pol 8) (Cable cable from cable tie is insulated)
Gray / Purple (Pol 14) (Cable connector from plug
insulated) Brown (Pol 15) (Cable connector from
connector insulated) Violet / Orange (Pol 16)
Green (Pol 20) (Cable wrench from cable tie
insulated)
5. Show the M15 module that has 5 cables
Black, Yellow, Blue, Orange, Green.
6. Connect as follows:
M15
Black
Yellow
Blue
The car
Insert black / blue cable (pole 13) into the black connector.
Connects to Gray / Brown (pole 4) from the connector.
Connect to Blue (pole 8) from the connector.
Orange
Green
Connect to Violet / Orange (pole 16) from the connector.
Connects to Green (pole 20) from the connector.
7. 7. Now pull the 5-meter cable that came with it from the data box to the right side under the glove
compartment and all the way back to the data box that you just made connections around.
8. The 5-meter cable has three cables in its own right. Brown, White and Green.
9. Inserts Green Cable for Brake Signal on C2280A Connector (Black) Pol 1. Cable Color: Violet / White Inserts
Brown Cable for Right Flashing on C2280F Connector (Black) Pol 38. Cable Color: Yellow / Violet Inserts
White Cable for Left Indicators on connector C2280F (black) Pol 39. Cable color: Blue / Green
10. 10. Adjust the cable length and then connect to the rear door as follows:
Green brake signal cable is connected to the following 6 cables:
White / Green (Pol 2) (Connects to cable to cable strap)
Brown / Purple (Pol 3) (Connects to cable to cable strap)
Gray / Brown (Pol 4) (Connects to cable to cable strap)
Gray / Purple (Pol 14) (Connects to cable to cable strap)
Brown (Pol 15) (Connects to cable to cable strap)
Violet / Orange (Pol 16) (Connects to cable to cable strap)
In total, 7 cables must be connected together in one point. Suitably,
you use a shrink tube to isolate.
11. Brown and White cable respectively connect to the right or left flashing lamp, which you can choose type
and model. Keep in mind that the maximum load on the flash circuit can not exceed 1A, which
corresponds to approximately 13w. A traditional light bulb approved for the 2a flashlight (ie rear flashes)
has an effect of 21w, which means that if connected, there is a high risk of data destruction being
destroyed. Only LED technology indicator lights shall be used to reduce the load on the car data base.
The appropriate grounding point for the blinkers is on the inside of the rear panel
slightly to the left of the boot lid lock under the loading threshold.
11. mount back the interior.
reconnect battery cable
included in the package:
✓1 M15 flashlight converter.
✓Installation instructions.
✓5 meter 3-pin cable.
You need:
»"You need:
»Shrink tube with melting inside
»Hot air gun
»ducktejp
»»wiring clamps
»»cutter
»»Cable scaler
BLACK CONNECTOR
SWELIGHT
BLACK CONNECTOR
Green
To the trunk
Violett/White
To the trunk
To the trunk
2280F
Blue / Green
White
Yellow/Violett
Brown