SWF RTS Installation manual

PROGRAMMING INSTRUCTIONS
1
S19002.37_RTS Solar Motors Programming Guide
Technical Support: call 800-544-4749 x3 or email [email protected]
STOP
CONTROLLER OVERVIEW
Single-channel Handheld Remote/
Wall Switch
Handheld Remote Wall Switch
Program
Button Program
Button Channel
Selector
Lights
indicate
selected
channel
Use
paper clip,
required
to program
button
Multichannel Handheld Remote/
Wall Switch
UP
DOWN
STOP/
INTERMEDI-
ATE POSITION
FRONT FRONT
BACK FRONT
ADJUSTING THE LIMITS
TO CHANGE THE LOWER LIMIT
1. Send the shade to its current lower limit.
2. Press both Up and Down at the same time until the
shade jogs. Adjust to a new lower limit position.
3. Press My or Stop until the shade jogs.
TO CHANGE THE UPPER LIMIT
1. Send the shade to its current upper limit.
2. Press both Up and Down at the same time until the
shade jogs. Adjust to a new upper limit position.
3. Press My or Stop until the shade jogs.
SETTING AN INTERMEDIATE POSITION (PREFERRED POSITION)
SETTING
1. Press the Up and Down to operate shade. At the desired
intermediate (preferred) position press My or Stop to
stop the shade.
2. Once the desired intermediate position is reached,
press and hold My or Stop until the shade jogs.
USING
1. Send the shade to the intermediate position by pressing
My or Stop from ANY shade position.
Note: Shade needs to be stationary prior to activating
intermediate position function.
RTS Motor Programming Instructions

PROGRAMMING INSTRUCTIONS
2
S19002.37_RTS Solar Motors Programming Guide
Technical Support: call 800-544-4749 x3 or email [email protected]
ADDING PROGRAMMED CHANNEL/CONTROLLER
1. Start on channel/controller currently operating
the shade.
2. Press and hold the programming button until the
shade jogs.
3. Select new channel/controller.
4. Press and release the program button until shade
jogs.
DELETING PROGRAMMED CHANNEL/CONTROLLER
NOTE: In order to complete this step, motorized
shade must be programmed to more than one
channel/controller.
1. Select the controller (single channel) or the
channel (1–5 of a multichannel controller) to be
kept.
2. Press and hold the programming button of that
controller until the shade jogs.
3. Select channel/controller to be deleted.
4. Press and release the programming button of that
controller until the shade jogs.
NOTE: Low voltage motors can be cleared of all
controllers by pressing and holding the motor
program button for two consecutive jogs.
ADDING AND DELETING A CHANNEL/CONTROLLER
Program
Button
Program
Button
Existing Controller
New Controller
DELETING AN INTERMEDIATE POSITION
1. Press and release the My or Stop to send shade to its
intermediate position.
2. Press and hold My or Stop for ve seconds until shade jogs.
RTS MOTOR

PROGRAMMING INSTRUCTIONS
3
S19002.37_RTS Solar Motors Programming Guide
Technical Support: call 800-544-4749 x3 or email [email protected]
PAIRING A CONTROLLER TO A MOTOR – LINE VOLTAGE MOTORS
ALL 120V AC RTS MOTORS
1. Unplug motor for two seconds.
2. Plug in motor for 10 seconds.
3. Unplug motor for two seconds.
4. Plug in. Shade will jog or briey move.
5. When the shade stops, press and release the
programming button on the controller and the shade will
jog again.
Note: The shade motor is exclusively paired for control to
this controller/channel.
RESET TO FACTORY MODE – LINE VOLTAGE MOTORS
ALL 120V AC RTS MOTORS
1. Unplug motor for two seconds.
2. Plug in motor for 10 seconds.
3. Unplug motor for two seconds.
4. Plug in. Shade will jog or briey move.
5. When the shade stops, press and hold the
programming button of any controller until the shade
jogs twice.
NOTE: Do not release the programming button until
the jogging is complete or you will have to repeat the
process.
RTS MOTOR

PROGRAMMING INSTRUCTIONS
4
S19002.37_RTS Solar Motors Programming Guide
Technical Support: call 800-544-4749 x3 or email [email protected]
RESET TO FACTORY MODE – LOW VOLTAGE MOTORS
SONESSE 30 (ST30) 24VDC AND R28 12VDC
1. Press and hold the motor program button until the
shade jogs three times.
ST30 24VDC R28 12VDC
PAIRING A CONTROLLER TO A MOTOR – LOW VOLTAGE MOTORS
SONESSE 30 (ST30) 24VDC AND R28 12VDC
1. Press and hold the motor program button
until the shade jogs once.
2. Press and release the programming button
on the controller.
ST30 24VDC R28 12VDC
RTS MOTOR