Swidget ZW006UWA User manual

Z-WAVE™ CONTROL + TEMPERATURE, HUMIDITY, AND MOTION INSERT INSTRUCTIONS
Model Number: ZW006UWA
Electrical Rating: 5VDC
The Swidget Z-Wave Control + Temperature, Humidity
and Motion Insert is a modular smart home solution
engineered for seamless integration with all Swidget
wiring devices. Swidget's Z-Wave Devices and Inserts
simplify the process of upgrading your home to a smart
living space. Swidget Devices are installed in your home
just like any other wiring devices, ensuring there is no
unnecessary complexity during installation. Once your
device is installed, simply select your desired sensor
capability, and snap your Swidget Z-Wave Insert into
the Swidget wiring device. The modularity of Swidget's
Inserts ensures that the solution is adaptable to your
needs as they change, and future-proofs your investment
by enabling you to adapt to new technologies, sensors,
and trends as they emerge.
Z-Wave Control Features
• Z-Wave Plus Certied with 800 series chipset
• Remote ON/OFF control via external Z-Wave
controller/hub.
• Manual ON/OFF control via front panel push button.
• User replaceable Insert – no electrician required
• Instantaneous W and kWh consumption for host
wiring device.1
• Independent meter reports for each receptacle when
used with a Swidget 15A or 20A outlet.
• OTA upgradeable rmware
Temperature, Humidity, and Motion Sensor Features
• Temperature Sensor between –10°C to 40°C (14°F to
104°F)
• Multilevel sensor reports for temperature, humidity.
• 0 to 100% RH (relative humidity) operating range
• PIR Motion Sensor (Wireless Infrared Detection)
• Occupancy/Vacancy detection
What's Included
• Swidget Z-Wave™ Control + Temperature, Humidity,
and Motion Insert ZW006UWA x 1
• Security Card x 1
• Packaging with QR on the outside to access the
instructions manual x 1
Swidget Wiring Devices
The Insert must be installed in a Swidget wiring device to
operate. The following wiring devices are available:
1. Auxiliary Control Switch - S16009WA
2. 20/40/60 Switch - S16008WA
3. Dimmer Switch - SD3001WA
4. 1P/3Way Switch - S16001WA
5. 15A Outlet - R1015SWA
6. 20A Outlet - R1020SWA
The nal features and functionalities will depend on your
selection of Insert + wiring device combination.
IMPORTANT
This Insert must only be installed and used with an
approved/certied Swidget wiring device. Usage with any
other devices is not permitted and will result in the
warranty becoming void.
WARNING
• While not required, it is recommended to avoid any risk
of shock or death, turn off power at the circuit breaker
or fuse and test that the power is off before installing or
removing any Insert.
• Not for use to control medical or life support equipment.
• For INDOOR use only: 0°C - 40°C (32°F - 104°F).
• Insert can only be installed in one orientation. Rear
alignment pins prevent incorrect installation. Do not
forcibly install an Insert.
• Do not use Swidget devices to control electric heaters
or any other appliances which may present a hazardous
condition due to unattended or unintentional or
automatic power on control.
• Requires a certied Z-Wave hub for operation.
• Double check any external Z-Wave settings for accuracy
before using them.
• This device complies with Z-Wave standard of open air,
line of sight transmission. Actual performance in a home
depends on the numbers of walls and obstacles between
the Insert and other Z-Wave devices / hubs.
• This device must be used in conjunction with an S2
Security Enabled Z-Wave Controller to fully utilize all
implemented security functions.
Installation
CAUTION
It is recommended to turn off power at the circuit breaker
or fuse and to test that the power is off before installing or
removing an Insert.
1. Orient the Insert to line up with the pins in the
wiring device cavity.
NOTE
Alignment pins will prevent incorrect installation.
2. Push Insert into the wiring device cavity until the
two side latches engage.
3. Re-enable power to the circuit breaker.
4. For a rst time installation or after an Insert reset,
the Insert requires network ADD pairing / joining
(see below).
5. For Inserts being moved, the Insert will power up
with the previous location settings. For any required
adjustments, consult the manual of the connecting
Z-Wave controller / hub.
Insert Operation
Z-Wave SmartStart
SmartStart enabled products can be added into a
Z-Wave network by scanning the Z-Wave QR Code
present on the product with a controller providing
SmartStart inclusion. No further action is required and
the SmartStart product will be added automatically
within 10 minutes of being switched on in the network
vicinity.
1. Follow SmartStart device ADD steps for your Z-
Wave controller / hub.
2. Use the Z-Wave controller / hub app or interface
to scan the QR code located on the security card
or directly on the Insert, or manually enter the 5
digit PIN or Insert's full DSK (Device Specic Key) as
required.
3. Once registered with your hub, the device will join
automatically within a minute of being placed in a
powered Swidget wiring device.
DSK located on the Insert DSK located on the security
card
Manual Z-Wave Network Add - Classic Inclusion
1. Follow network ADD steps for your Z-Wave
controller / hub.
2. Lightly press Insert push button and hold for 5-10
seconds until the LED illuminates solid blue, then
release. LED will ash blue to indicate ADD mode is
enabled. No manual or external Z-Wave operations
are possible during this activity.
3. Insert will remain in ADD mode for up to 30 seconds.
If successful, LED will be solid blue for 5 seconds
then return to the normal operational state. IF
FAILED to connect after 30 seconds, the red LED
will ash for 3 seconds, indicating no or failed
network ADD. If necessary, consult your Z-Wave
controller/hub manual and retry.
Manual Z-Wave Network Remove - Classic Exclusion
1. Follow network REMOVE steps for your Z-Wave
controller / hub.
2. Lightly press Insert push button and hold for 5-10
seconds then release. LED will ash blue to indicate
REMOVE mode is enabled. No manual or external
Z-Wave operations are possible during this activity.
3. Insert will remain in REMOVE mode for up to 30
seconds. If successful, LED will be solid blue for 5
seconds then return to the normal operational state.
If FAILED to connect after 60 seconds, red LED
will ash indicating no or failed network REMOVE.
If necessary, consult your Z-Wave controller / hub
manual and retry.
Z-Wave Local Device Reset (Factory Reset)
NOTE
Should only be used when the original controller is
inoperable or has been replaced.
1Not applicable to Auxiliary and 20/40/60 Control Switch
IMPORTANT SAFETY INSTRUCTIONS
1 ©2023 SWIDGET CORP. ALL RIGHTS RESERVED. Z-Wave™ Control + Temperature, Humidity, And Motion Insert Instructions - DDS50N0199

1. Lightly press Insert push button and hold for 10-15
seconds until the LED turns SOLID RED, and then
release.
2. The Insert will cycle through led colours (R-G-B).
When LED stops cycling, reset is complete.
Manual Device Switching
1. Lightly press the Insert push button and hold for 1-5
seconds then release. The wiring device will toggle
states.
Insert Button Actions
Button press and
hold
LED State Action
Less than 1 sec No change None
1 - 5 sec Green ON or OFF Manual device
ON/OFF toggle
5 - 10 sec Blue ON Network ADD/
REMOVE mode
10 - 15 sec Red ON Device local reset
(factory reset)
More than 15 sec OFF None
Association Groups
An Association Group in Z-Wave technology is a list
of linked devices that allows direct communication
between them, bypassing the need for a hub or
controller. Each group, or set of devices, is linked with
a specic event, such as motion detection. The device
initiating the communication, known as the "source," can
send commands to the "target" devices within the group.
The number of Association Groups a Swidget Insert
can support will vary depending on the Insert features
and the Swidget wiring device it is installed in. Each
association group can support up to 5 targets (nodes).
Please refer to the Swidget Z-Wave Product Manual for
additional information.
Command Classes
Command Class Ver Required
Security
Class
Supported
Swidget
wiring
devices
Z-Wave Plus™ Info 2 None All
Basic 2 Highest
Granted
Security
Class
All
Binary Switch 2 Highest
Granted
Security
Class
All except
Dimmer
Switch
Multilevel Switch 4 Highest
Granted
Security
Class
Dimmer
Switch only
Command Class Ver Required
Security
Class
Supported
Swidget
wiring
devices
Association 2 Highest
Granted
Security
Class
All
Meter 6 Highest
Granted
Security
Class
All except
Auxiliary
Control
Switch and
20/40/60
Control
Switch
Conguration 4 Highest
Granted
Security
Class
All
Notication 8 Highest
Granted
Security
Class
All
Multilevel Sensor 11 Highest
Granted
Security
Class
All
Multi-Channel 4 Highest
Granted
Security
Class
15A and 20A
Outlets and
USB Insert
Multi-Channel
Association
3 Highest
Granted
Security
Class
15A and 20A
Outlets and
all Inserts
Association Group
Information
3 Highest
Granted
Security
Class
All
Transport Service 2 None All
Version 3 Highest
Granted
Security
Class
All
Manufacturer
Specic
2 Highest
Granted
Security
Class
All
Device Reset
Locally
1 Highest
Granted
Security
Class
All
Indicator 3 Highest
Granted
Security
Class
All
Powerlevel 1 Highest
Granted
Security
Class
All
Security 1 None All
Security 2 2 None All
Supervision 1 None All
Command Class Ver Required
Security
Class
Supported
Swidget
wiring
devices
Firmware Update 5 Highest
Granted
Security
Class
All
Basic Command Class Support
If the Z-Wave Insert registers as a Binary Switch Device
Type in a non-multi-channel environment, then the Basic
Command Class functions are mapped to the Binary
Switch Command Class functions.
If the Z-Wave Insert registers as a Binary Switch Device
Type in a multi-channel environment, then the Basic
Command Class functions are mapped to the Binary
Switch Command Class functions for Endpoint 1 (the
Root node). For Endpoint 2, no mappings exist for the
Basic Command Class, so any Basic Commands received
by Endpoint 2 will be ignored, and no report will be
generated.
If the Z-Wave Insert registers as a Multilevel Switch
Device Type, then the Basic Command Class functions
are mapped to the Multilevel Switch Command Class
functions.
FCC Compliance Statement
This device complies with part 15 of the FCC and ISED
Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received,
including interference that may cause undesired
operation.
FCC Note
The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modications to
this equipment. Such modications could void the user’s
authority to operate the equipment.
Note:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Important Note:
To comply with the ISED Canada and FCC RF exposure
compliance requirements, no change to the antenna or
the device is permitted. Any change to the antenna
or the device could result in the device exceeding the
RF exposure requirements and void user’s authority to
operate the device.
Swidget FCC/IC
Contains FCC ID: 2AR26-SWIDGETZW100
Contains IC: 24603-SWDTZW10100
Z-Wave Interoperability
This product can be operated in any Z-Wave network
with other Z-Wave certied devices from other
manufacturers. All mains operated nodes within the
network will act as repeaters regardless of vendor to
increase reliability of the network.
Warranty
After having been installed according to your local
electrical code and by a certied electrician when
applicable, and having been used within normal
operating conditions, Swidget Corp. will repair or
replace (at Swidget’s discretion) any product that fails
due to manufacturing defects for a period of 5 years for
Swidget Host Devices and for a period of 2 years for
Swidget Inserts. Any repair or replacement of defective
products will extend the warranty by 90 days or the time
remaining on the original warranty, whichever is longer.
Post warranty repairs are not available.
Swidget shall not be held liable under this
warranty for reasonable wear and tear, or
damage(s) caused by the following: misuse, neglect,
improper installation, abnormal operating conditions,
unauthorized modications or attempts to repair the
product.
Any claims to Swidget made under this warranty shall
not exceed the cost of the repairs or replacement of the
product.
IMPORTANT SAFETY INSTRUCTIONS
2 ©2023 SWIDGET CORP. ALL RIGHTS RESERVED. Z-Wave™ Control + Temperature, Humidity, And Motion Insert Instructions - DDS50N0199

This warranty applies only to Swidget products
purchased from an authorized distributor or retailer, and
as such, Swidget reserves the right to request proof of
purchase, and reject claims for purchases made through
unauthorized distributors or retailers.
Please direct warranty claims to Swidget Corp.
by telephone at 1-855-202-1144, email at
[email protected] with subject Warranty Claim.
Each warranty return must be accompanied by a
completed Return Merchandise Authorization (RMA)
form provided by Swidget Customer Service
Problems Or Questions:
If you have any problems with or questions about the
Swidget device or Insert, contact our tech support team:
[email protected]
For the most up-to-date product support, accessories,
user manuals and more, visit www.swidget.com or scan
the following QR code:
http://zw006uwa-qr.swidget.com/
There are no user serviceable parts in this unit.
If you have problems with your Z-Wave hub, please
consult the manufacturer for the appropriate support.
IMPORTANT SAFETY INSTRUCTIONS
3 ©2023 SWIDGET CORP. ALL RIGHTS RESERVED. Z-Wave™ Control + Temperature, Humidity, And Motion Insert Instructions - DDS50N0199