Swisher WB11524BS User manual

THE PREDATOR
THE PREDATORTHE PREDATOR
THE PREDATOR
24
2424
24”
””
” WALK BEHIND
WALK BEHIND WALK BEHIND
WALK BEHIND
ROUGH CUT
ROUGH CUTROUGH CUT
ROUGH CUT
OWNER’S
MANUAL
1602 CORPORATE DRIVE, WARRENSBURG MISSOURI 64093
PHONE [phone] FAX [phone]
MODEL NO.
Operation
Service and Adjustment
Repair Parts
Made In The
USA
REV 12-341
WB11524BS
swisherinc.com
10 50
STARTING SERIAL #:
L112-341001
Read and follow all
Safety Precautions
and Instructions
before operating this
equipment.
IMPORTANT
Meijer.com

2
In the event you have a claim unde this wa anty, you must etu n the p oduct to an autho ized
se vice deale . All t anspo tation cha ges, damage, o loss incu ed du ing t anspo tation of pa ts
submitted fo eplacement o epai unde this wa anty shall be bo ne by the pu chase . Should you
have any questions conce ning this wa anty, please contact us toll-f ee at 1-800-222-8183. The
model numbe , se ial numbe , date of pu chase, and the name of the autho ized Swishe deale f om
whom you pu chased the mowe will be needed befo e any wa anty claim can be p ocessed.
THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME
PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not
allow the limitation of consequential damages o limitations on how long an implied wa anty may
last, so the above limitations o exclusions may not apply to you. This wa anty gives you specific
legal ights and you may have othe ights, which va y f om state-to-state. This is a limited wa anty
as defined by the Magnuson-Moss Act of 1975.
LIMITED WARRANTY
The manufactu e ’s wa anty to the o iginal consume pu chase is: This p oduct is f ee f om defects
in mate ials and wo kmanship fo a pe iod of (1) yea f om the date of pu chase by the o iginal
consume pu chase . We will epai o eplace, at ou disc etion, pa ts found to be defective due to
mate ials o wo kmanship. This wa anty is subject to the following limitations and exclusions:
TABLE OF CONTENTS
WARRANTY………………....….2
INTRODUCTION………………..3
SAFETY..……………………….3-4
PRE-OPERATING..….……..……4
OPERATION.……………………….5-7
DECALS…..………….……………….8
PARTS BREAKDOWN…………….9-13
SAFE SLOPE GUIDE..………………15
1) Engine Wa anty All engines utilized on ou p oducts have a sepa ate wa anty extended
to them by the individual engine manufactu e . Any engine se vice
difficulty is the esponsibility of the engine manufactu e and in no
way is Swishe o its agents esponsible fo the engine wa anty. The
B iggs & St atton Engine Se vice Hot-Line is 1-800-233-3723.
2) Comme cial Use This p oduct is not intended fo comme cial use and ca ies no
comme cial wa anty.
3) Limitation This wa anty applies only to p oducts which have been p ope ly
assembled, adjusted, and ope ated in acco dance with the inst uctions
contained within this manual. This wa anty does not apply to any
p oduct of Swishe that has been subject to alte ation, misuse, abuse,
imp ope assembly o installation, shipping damage, o to no mal wea
of p oduct.
4) Exclusions Excluded f om this wa anty a e no mal wea , no mal adjustments, and
no mal maintenance.
Meijer.com

SAFETY PRECAUTIONS
This Safety Alert Symbol indicates important messages in this
manual. When you see this symbol, carefully read the message that
follows and be alert to the possibility of personal injury.
Read this manual completely. This machine can amputate hands and feet, and
throw objects. Failure to observe the following safety instructions could result in
serious injury or death.
Thank you fo choosing Swishe ’s 24” Walk Behind Rough Cut. Befo e
ope ating you Walk Behind, please ead, unde stand and follow all of the safety
p ecautions and othe inst uctions explained in this manual. As with all powe
equipment, lawn mowe s can be potentially dange ous if not p ope ly used.
3
• Read the manual. Lea n to ope ate this machine safely.
• Always disconnect the spa k plug wi e and place the wi e whe e it cannot contact the
spa k plug, to p event accidental sta ting the engine when setting up, t anspo ting,
adjusting o making epai s.
• Keep all shields and gua ds in place.
• Unde stand the speed, stee ing and stability of this machine. Know the positions and
ope ations of all cont ols befo e you ope ate this machine. Check all of the cont ols in
a safe a ea befo e sta ting to wo k with this machine.
• Allow only esponsible adults who a e familia with these inst uctions to ope ate this
machine. Never allow children to operate this machine.
• Clea the a ea of objects such as ocks, toys, wi e, etc. that can be picked up and
th own by the blade.
• Be su e the a ea is clea of othe people befo e mowing. Be awa e of the mowe
discha ge di ection and do not point at anyone. Stop the machine if anyone ente s the
mowing a ea. Child en a e often att acted to the machine and the mowing activity.
Never assume that children will remain where you last saw them. Keep child en
unde the watchful ca e of anothe esponsible adult.
•No riders!
• Do not put hands o feet nea o unde otating pa ts.
• Do not mow in eve se. Always look down and behind before and during backing.
Meijer.com

• Tu n off the blade when not mowing. Befo e leaving the machine, tu n off the blade
and stop the engine.
• Watch fo t affic when ope ating nea o c ossing oadways.
• Do not ope ate the mowe if it has been d opped o damaged in any manne o if the
mowe vib ates excessively. Excessive vib ation is an indication of damage. Repai mowe
as necessa y.
• D ess p ope ly. Do not ope ate the mowe when ba efoot o wea ing open sandals. Wea
only solid shoes with good t action when mowing.
• Neve allow ope ation by unt ained pe sons.
• Do not ope ate the machine while unde the influence of alcohol o d ugs.
• Do not ope ate on slopes g eate than 15 deg ees.
• Neve tampe with safety devices. Check thei p ope ope ation egula ly.
• Stop and inspect the equipment if you st ike an object. Repai , if necessa y, befo e
esta ting. Neve make adjustments o epai s with the engine unning.
• Mowe blades a e sha p and can cut. W ap the blades o wea gloves, and use ext a
caution when se vicing them. Do not ope ate at too fast a ate.
• Disengage spa k plug wi e and place whe e it cannot make a connection.
• Check engine oil. All engines a e filled with oil at the facto y. Ve ify oil level and
add if necessa y befo e sta ting engine (See Engine Owne ’s Manual).
• Ve ify fuel level and add if necessa y befo e sta ting engine.
• Reconnect spa k plug wi e.
• Refe to pages 5-7 in this manual fo p ope ope ating p ocedu es.
PRE-OPERATING INSTRUCTIONS
4
Meijer.com

The ope ation of any mowe can p oduce fo eign objects to be th own into the
eyes, esulting in seve e eye damage. Always wea ce tified safety glasses o
wide-vision safety goggles ove spectacles befo e sta ting any cutting machine and
while ope ating such a machine.
The ope ation of any mowe p oduces sound waves that a e damaging to the
human ea . Ea p otection is ecommended.
CAUTION!
T agic accidents can occu if the ope ato is not ale t to the p esence of
child en. Child en a e often att acted to the machine and the mowing
activity. Never assume that children will remain where you last saw them.
OPERATING YOUR NEW WALK BEHIND
INTENDED USE
This is not a lawn mowe . The P edato is designed fo cutting ove g own b ush, weeds,
and othe types of o ganic g owth. This unit is capable of clea ing small saplings of 1.5”
in diamete o less.
PROPULSION
The P edato is self-p opelled and is cont olled by a “GROUND CONTROL” leve . To
engage the d ive, put the t ansaxle in a gea and activate the left leve . Releasing the
leve will disengage the self-p opel.
Unde most conditions cutting should be done in a low gea (1st o 2nd). Uppe gea s
should be used fo conditions whe e weeds and b ush a e thinned out o not as tall. In
confined a eas the machine can be pushed fo wa ds o backwa ds by eleasing the
“GROUND CONTROL” leve , placing the t ansaxle in neut al, and pushing the
machine.
TRAVEL SPEED
Speed can be va ied by choosing a highe o lowe gea using the gea shift leve at the
ea of the machine o by changing the engine speed with the engine th ottle. Do not
adjust speed with the blade engaged. To shift the cutte into eve se, elease “GROUND
CONTROL” leve , disengage blade, and otate the shift leve to the left. When the leve
stops, lift up the eve se lockout latch and continue to move the shift leve to the left until
it stops again. The Predator is equipped with a safety control that will kill the engine
if the blade is engaged while cutter is in the “REVERSE” gear.
ENGAGING BLADE
An “OPERATOR PRESENCE” leve and a “BLADE ENGAGE DRIVE” cont ol wo k
togethe to engage the P edato ’s blade. Both devices must be activated befo e the blade
will wo k. Releasing the “OPERATOR PRESENCE” leve will disengage both the blade
and the “BLADE ENGAGE DRIVE” cont ol.
5
Meijer.com

STARTING THE ENGINE
See engine manufacturer’s recommendations for the type and amount of oil and fuel used.
Engine must be level to accurately check and fill oil. Do not overfill.
• Make sure unit is level, blade is disengaged, and transaxle in NEUTRAL”
• Check spark plug wire, oil level, and fuel level.
• Check all electrical connections for build-up of debris.
• If needed set CHOKE” to choke position.
• Set engine throttle control to ½ throttle position.
• Pull rope with a single fluid motion.
• After engine has started set CHOKE” to RUN” position.
STOPPING
• Bring the Walk Behind to a complete stop.
• Disengage mower blade.
• Reduce engine idle speed, and allow engine to run momentarily for cooling.
• Place transaxle in the NEUTRAL” position.
• Move engine throttle control to OFF” position.
HEIGHT ADJUSTMENT
• Place two 6” wooden blocks under the deck on the side being adjusted.
• Remove nuts and bolts from the side runner.
• Slide skid up or down to preferred position.
• Replace the nuts and bolts making certain they are tightened securely.
• Repeat for the other side. Runners should be at the same height.
BREAKING IN YOUR WALK BEHIND
• Start engine properly.
• Slowly engage blade control.
• Under supervision, allow blade to rotate and engine to idle for 5 minutes.
• Disengage blade.
• Shift through each gear. While in each gear engage the GROUND CONTROL” lever
and travel 20 yards to ensure transaxle works properly.
BEGIN CUTTING
• Make sure area is clear of all bystanders.
• Make sure that all guards, belt guides, and the spark plug wire are properly attached.
• Start engine, set engine throttle control at maximum engine idle speed for best results.
• Allow engine to run a few moments and slowly engage blade.
• Move transaxle into low gear and activate GROUND CONTROL” lever.
• Turning is done by rotating the handles left or right. This machine has significant
weight and may take more effort to turn than one may expect. Turning could take
practice.
BACKING UP
• Disengage blade.
• Check behind you for safety.
• Move transaxle into REVERSE” position.
• Activate GROUND CONTROL” lever.
6
IMPORTANT: This engine is not equipped with a spark arrester muffler. It is a violation of
California Public Resource Code Section 444 to use or operate the engine on any forest-covered,
brush-covered, or grass-covered land. Other states or federal areas may have similar laws.
Meijer.com

TRANSPORTING
• Shut off engine.
• Secu e in place while unit is being t anspo ted.
• Unit should be left in low gea to avoid any slight olling.
SUGGESTED PRACTICES
• Always ope ate engine at full th ottle when cutting to assu e the best cutting
pe fo mance and p ope discha ge of mate ial.
• If g ass is wet, allow it to d y. Wet g ass clumps will collect on the bottom of the
deck.
• Go slow when cutting dense a eas. Some dense a eas may need to be gone ove
twice. Bette esults occu if the second cut is 90 deg ees to the fi st cut.
BEFORE EACH SEASON
A new spa k plug and clean ai filte assu e p ope ai -fuel mixtu e and help you engine un
bette and last longe .
• Replace the spa k plug.
• Clean o eplace the ai filte .
• Check blades and belts fo wea .
BEFORE EACH USE
• Check engine oil level. Do this twice to ensu e an accu ate eading.
• Check condition of ai filte and clean o eplace if necessa y.
• Check blade ope ation.
• Check fo loose fastene s.
DAILY MAINTENANCE
Make su e all nuts and bolts a e tight and cotte pins and etaine sp ings a e secu e.
Keep blades sha p. Obse ve all safety p ecautions.
BLADE CARE AND SERVICE
Fo best esults blades must be kept sha p. The blades can be sha pened with a few st okes of a
file o g inding wheel. Do Not attempt to sha pen blades while they a e on the machine.
Important: Replace blades that have been damaged or deeply nicked.
Important: Check blade and spindle hardware on a regular basis to make sure nuts are
tight.
Meijer.com

SAFETY AND OPERATIONAL DECALS
Replace decal immediately if damaged. O de by pa t numbe f om Swishe .
OD39--SWISHER FLAG DECAL
OD55--DANGER DECAL OD45--WARNING DECAL
OD83--RN1234 SHIFT DECAL
10749--REVERSE LOCK DECAL
DECALS NOT SHOWN
OD85--P edato LH Decal
OD86--P edato RH Decal
OD87--Rugged Cut 24 4SP T ans White Decal
8
OD99112—LARGE LOGO WHITE DECAL
Meijer.com

OVERALL ASSEMBLY
9
When o de ing eplacement pa ts
*USE PAINT CODE: TK=BLACK
Item # Description Part #
1 Cover - Belt 10682*
2 Bolt - Serrated Flange 5/16-18 X 3/4 NB596
3 Nut - Serrated Flange 5/16-18 NB170
4 C annel - Rig t Side 10676*
5 C annel - Left Side 10677*
6 Clip - Tinnerman 5/16-18 3706
7 Bolt - Serrated Flange 5/16-18 X 2 1/4 NB622
Meijer.com

ENGINE-PULLEY ASSEMBLY
BELT
CONFIGURATION
WIRING
CONFIGURATION
1
13
10
6
5
14
11
12
8
4
2
9
Goes in Rea
Mounting Hole
2
NOT ACTUAL ENGINE
USED (REF. ONLY)
Item # Description Part #
1 Motor Plate 10678*
2 5/16-18 Serr. Flange Nut NB170
3 5/16-18 X 3/4 Serr. Flange Bolt NB596
4 Belt Retention Weldment 10767
5 Engine Pulley Spacer 1.75" Long BB105S
6 1/4 X 1/2 Key Stock 4258
7 Engine Pulley- 2.5" 2411
8 1 X 1 1/2 10GA Was er NB614HT
9 1/4 X 1 Key Stock 9031
10 Engine Pulley- 4.25"OD,1 1/4 ID BB105
11 Was er, Front W eel (Heat Trtd) TR150W
12 Was er Belleville 699
13 7/16-20 X 1 1/2 HCF GR5 ZP NYLOC NB637
14 3/8-16 X 1 1/2 HCCG NB107
15 3/8 SAE Was er NB272
16 Idler Pulley OD-2.16", ID-3/8" B27
17 3/8-16 2 Way Locking Nut NB280
18 3/8-16 X 1 GR5 ZP Bolt NB604
19 Idler Bus ing 6037
20 Idler Arm 10671*
21 1/4-20 X 3/4 GR5 ZP Bolt NB250
22 1/4-20 Serr. Flange Nut NB524
23 Spring T2SM
24 5/16-18 X 1 1/4 Serr. Flange Bolt NB253
25 Transmission Belt-33" 690
26 Engine B&S Recoil St W/Gas Tank N/A
27 Transmission Cable 2432
15
SSB
9113
10
10765
BROWN
2472
BROWN
20
17
6114 – BLADE PULLEY
3
16
18
19
25
21
22
17
24
24
Impo tant: Sp ing
must be hooked in
Idle A m as shown
23
Install T ansmission Cable Item
#27 in Idle A m befo e installing
Idle A m to Moto Plate
26
7
2
2410
TRANSAXLE PULLEY
690 – TRANSAXLE BELT
TOP ENGINE PULLEY
CONFIGURATION
B2 – TRANSAXLE IDLER PULLEY 2411 – TOP ENGINE PULLEY
BB105 – LOWER ENGINE PULLEY
T30V – V-BELT PULLEY
B52 – BLADE IDLER PULLEY
BA50 – BLADE ENGAGEMENT BELT
BOTTOM ENGINE PULLEY CONFIGURATION
ATTACH TO
MAGNETO
NOTE: WIRES MUST PASS THROUGH ALL WIRE GUIDES POSSIBLE
When o de ing eplacement pa ts
*USE PAINT CODE: TK=BLACK
Meijer.com