Swisson XRC-CT15 User manual

XRC-CT15
External Trigger
Contacts for XRC-150
User Manual

2
XRC-CT15 External Contacts Trigger for XRC-150
User Manual
Issue 1 (2007-26-02)
Copyright © 2007 SWISSON AG
No part of this documentation may be reproduced
or transmitted in any form or by any means,
electronic or mechanical, including photocopying
and recording, without the prior written permission
of SWISSON AG.
The information in this documentation is supplied
without warranty of any kind, either directly or
indirectly, and is subject to change without prior
written notice. SWISSON its employees or
appointed representatives will not be held
responsible for any damages to software,
hardware, or data, arising as a direct or indirect
result of the product(s) mentioned herein.
Issued by
SWISSON AG
Fabrikstrasse 21
CH-3250 Lyss
Switzerland
E-Mail: [email protected]

3
Table of contents
Table of contents ........................................... 3
Overview........................................................ 4
General Description....................................... 5
Connecting the XRC-CT15 to the XRC-150 ..6
Connection ................................................. 6
Connecting Cable....................................... 7
Opening the XRC-CT15................................. 8
Connecting contacts to the XRC-CT15.......... 9
Using internal Power ..................................9
Using external Power .................................9
Configuration ............................................... 10
Technical Data............................................. 11
Absolute Maximum ratings ....................... 11
Operating Conditions................................ 11
Safety notes................................................. 12

4
Overview
1
2
3
4
1 Port Connector
The XRC-CT15 is connected with
the XRC-150 through this port.
2 Cable Glands
Glands for cables connected in the
XRC-CT15
3 Lid
The lid of the XRC-CT15 can be
removed for connection of the
contacts
4 Lid Screw
This screw holds the lid on the XRC-
CT15

5
General Description
The XRC-CT15 is an accessory for use with the
XRC-150. On this device up to 15 external trigger
contacts can be connected.
With these contacts the XRC-150 can be controlled
remotely:
Contacts 1 .. 15
XRC-CT15
XRC-150
Each button can be configured to start, stop or
pause, play back of a sequence on the XRC-150.

6
Connecting the XRC-CT15 to
the XRC-150
Connection
The XRC-CT15 can be easily connected to the
XRC-150 through running a cable from an external
port of the XRC-150 to the XRC-CT15:
It doesn’t matter on which port (port #1 or #2) the
XRC-CT15 is connected to the XRC-150.

7
Connecting Cable
The connection of the XRC-CT15 to the XRC-150 is
done with a standard RJ45 8 pole STRAIGHT
network cable:
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
The speed of the data transmission between the
XRC-CT15 and the XRC-150 is 250 kBaud.
Therefore, the cable mustn’t be very high quality.

8
Opening the XRC-CT15
To connect the XRC-CT15 with external trigger
contacts, the lid must first be removed. Simply
remove the lid screw:
Lid Screw
Slide out the lid of the XRC-CT15:
Now you can see the connecting ports (1 – 15) for
the external trigger contacts and also two
connectors of the internal power (VCC and GND):

9
Connecting contacts to the
XRC-CT15
Using internal Power
Using the internal power of the XRC-CT-15 is a
very simple way to connect external trigger contacts
to the device.
Simply connect a switch, button, relay or another
contact with one connection to the internal supply
voltage (VCC) of the XRC-CT-15, and the other
connection to a dedicated input of the device:
VCC
1
2
15
XRC-CT15
Using external Power
When using external power, it’s necessary to
connect GND of the XRC-CT15 to the voltage
reference (ground) on the external device:
Voltage of
external device
1
2
15 Reference (Ground)
of external device
GND
XRC-CT15 External Device
ATTENTION:
When using external power, you have to take
attention to the maximum ratings!!! (See chapter
Absolute Maximum ratings on page 11)

10
Configuration
Every time a contact is activated, the XRC-CT15
sends this information to the XRC-150.
Therefore it’s possible to configure each contact
activity on the XRC-150 to either start, stop or
pause, a sequence.
To configure the contacts, go to the menu point
“External Devices” in the XRC-150 main menu and
press the confirm/select button. Now scroll to
“Contacts Configuration” and press the
confirm/select button again. The following will
appear on the display of the XRC-150:
Now you need to choose the contact by activating
it. For example if you have connected a switch on
contact1, press this switch to configure contact1:
There are three different possible actions:
1. Play Sequence:
This will start playback of one of the 32
different sequences (the sequence can be
set)
2. Pause:
This will set the XRC-150 to pause or
release the XRC-150 from pause during
playback.
3. Stop:
This will stop the XRC-150 during play
back or recording.