Symbol LS-2100U User manual

1

2
Installation
Installing the Keyboard Wedge Reader
To install a keyboard wedge reader, follow the steps below:
1. Turn off the power of the PC or Terminal.
2. Unplug keyboard from the PC or Terminal.
3.
Make sure you have the Y cable with appropriate
connector type for your PC or Terminal.
4. Connect Scanner to your PC or Terminal.
5.
Connect the keyboard connector to the female connector
of the Y cable
6. Turn on the power of PC or Terminal.
Installing the RS232 Reader
To install a RS232 reader, follow the steps below:
1. Turn off the power of the PC or Terminal.
2.
Make sure the connector type from RS232 to the PC or
Terminal is correct.
3. Plug ACAdaptor connector into connector of the reader.
4. Turn on the power of PC or Terminal.
5. Setup the Interface of the reader to RS232 mo
de by
scanning the barcode in the Interface Selection.

3
Method of Programming
Loop of programming
The philosophy of programming parameters has been show on
the flow chart. Basically user should
1. Scan Start of Configuration.
2. Scan all necessary labels for parameters that meet
applications.
3. Scan End of Configuration to end the programming.
4. To go bark to the Default Settings, just scan label for Set
All Defaults.
Factory Default Settings
The factory default settings are shown with < >and bold in the
following sections. You can make your own settings by following
the procedures in this manual.
By scanning” Set All Default” label, the settings will go back to the
factory default settings.

4
Setup Commands
Set All efaults
Set all the parameters to the
factory default setting.
Start Configuration.
End Configuration.
Abort Configuration
Terminate current programming
status.
Version Information
Display the decoder version
information and date code

5
Interface Selection
<Keybard Mode>
RS232 Mode
USB Mode
Start Configuration Abort Configuration

6
Reading Mode
<Good Read Off> Flash-On
Trigger On/Off
Continuous/Trigger Off Testing
Continuous/No Trigger
Trigger ON/Good Read Off/Delay=??
*This mode is almost the same as
<Good Read OFF> but you can delay
time for turning off LED<Default is 3
seconds> you can use the provided
Decimal and Hex-Label Tables for you
r
own setup.
Trigger On/Good Read
Off/Delay=??
Continuous/Trigger Off/Delay=??
*This mode you can define the delay
time to control the LED off after
releasing the trigger.
Continuous/Trigger Off
End Configuration

7
RS-232 Communication Parameters
Set Up BAU Rate
300 <9600>
600 19200
1200 38400
2400
4800
Start Configuration Abort Configuration

8
RS-232 Communication Parameters
Set Up ata Bits:
7 Data Bits
<8 Data Bits>
Set up Parity:
<None>
Even
Odd
End Configuration

9
RS-232 Communication Parameters
Handshaking
<None>
RTS/CTS Enable
ACK/NAK Enable
XON/XOFF Enable
Start Configuration Abort Configuration

10
RS-232 Communication Parameters
(ACK/NAK Response Time CTS Observation Time:)
ACK/NAK Time Out=??
Scan Start Configuration Label
Scan ACK/NAK Time-out Label
Scan Two Digit Labels in Table–Hex
Scan Confirm Label in Table-Hex
Scan End Configuration Label
RTS/CTS Time Out=??
Scan Enter Start Configuration Label
Scan RTS/CTS Time-Out Label
Scan Two Digit Labels in Table–Hex
Scan Confirm Label in Table-Hex
Scan End Configuration Label
RTS Signal status:
Normal LOW <Normal High>
End Configuration

11
Keyboard Wedge Parameters
Terminal Type
<IBM PC/AT, PS/2>
UPPER/LOWER Case
ATUTO <Lower Case>
Upper Case
Send character by ALT Method
Enable ALT MODE
(ALT+HOT KEY)
Select Numerical Pad
ALT MODE
(ALL DATA FOR ALT)
On <Off>
Bar-space invert to Read
Yes <No>
Start Configuration Abort Configuration

12
Language Selection
<US English> Poland
UK English Japanese
Italian Belgium
Spanish Portuguese
French Demark
Germany Netherlands
Swedish/Finnish Norway
Swiss Latin America
End Configuration

13
Output Characters Parameters
Select Terminator
Keyboard
NONE
<CR>
SPACE
TAB
ESC
Start Configuration Abort Configuration

14
Output Characters Parameters
Select Terminator
RS232
NONE ESC
<CR> CTR-C
CR/LF STX..XOFF
LF XON..XOFF
SPACE EOT
TAB
End Configuration

15
Code I
Code I Selection
CODE ID=ON <CODE ID=OFF>
Code Length
On Off
Select Code I Set
Set<user defined> Set1
Set2 Set3
Set4 Set5
Set6 Set7
Note1: UP to two characters of code ID can be
configured for each symbology when you select
user defined.
Note2: User Can First select one of the code Id
sets and then make desired modifications the
pre-defined Code ID sets are shown next page table.
Start Configuration Abort Configuration

16
End Configuration
Code I Set1-Set5 Table
Set1 Set2 Set3 Set4 Set5
Code 39
A C Y M A
Italy Pharmacode
A C Y M A
French
Pharmacode
A C Y M A
Industrial 25
C H H H S
Interleave 25
D I Z I S
Matrix 25
E G G G S
Codabar
F N X N F
Code 93
I L L L G
Code 128
H K K K C
UPCE
S E C E E
EAN8
P B B FF E
EAN13
M A A F E
MSI
V V D P M
Plessey
W W E Q P
UPCA
M A A A E

17
Code I
Bar Code I <USER EFINE >
CODE 39 MSI/PLESSEY
INDUSTRIAL 2 OF 5 ENA-13
CHINA POSTAGE UPC-E
CODE 93 INTERLEVED 2 OF 5
MATRIX 2 OF 5 CODABAR/NW7
CODE 128 EAN-8
UPC-A
Note: Refer to ASCII Table; scan two hexadecimal labels in
Table-hex to represent one character.
Start Configuration Abort Configuration

18
Misc. Parameters
Buzzer Beep Tone
Buzzer Pitch=?? (0-22) Buzzer Duration=?? (0-127)
Power up Tone
<On> Off
LE Indicator
<Normal On Good Read Off> Normal Off Good Read On
Keyboard Speed of PC/AT
<Normal> Turbo
Single Scan <Double Scan>
End Configuration

19
Code Option
UPC-A/EAN-13
<On> Off
UPC-E
<On> Off
EAN-8/JAN-8
<On> Off
CO E 39
<On> Off
CO E 128
<On> Off
CO ABAR/NW7
<On> Off
Start Configuration Abort Configuration

20
Code Option
Interleave25
<On> Off
Industrial 25
On < Off >
UCC EAN/128
On < Off >
Matrix 25
On < Off >
CO E 93
<On> Off
End Configuration