Synology RackStation RS814+ User manual

Synology_QIG_RS814+&RS814RP+_20131025
Synology RackStation RS814+/RS814RP+
Quick Installation Guide

2
Table of Contents
Chapter 1: Before You Start
Package Contents .............................................................................................................................................................. 3
Synology RackStation at a Glance................................................................................................................................... 4
Safety Instructions .............................................................................................................................................................. 6
Chapter 2: Hardware Setup
Tools and Parts for Drive Installation............................................................................................................................... 7
Install Drives........................................................................................................................................................................ 7
Add a RAM Module on RackStation ................................................................................................................................ 9
Start up the RackStation.................................................................................................................................................. 11
Chapter 3: Install DSM on RackStation
Install DSM with Web Assistant...................................................................................................................................... 12
Learn More ........................................................................................................................................................................ 13
Appendix A: Specifications
Appendix B: LED Indicator Table

3
Chapter
1
Chapter 1: Before You Start
Thank you for purchasing this Synology product! Before setting up your new RackStation, please check the
package contents to verify that you have received the items below. Also, make sure to read the safety
instructions carefully to avoid harming yourself or damaging your RackStation.
Package Contents
Main unit x 1 AC power cord x 11
Rack mount kit x 2
Screws for 3.5"
hard drives x 20
Screws for 2.5"
hard drives x 20 Rack mount kit nuts x 5 Hard drive tray key x 2
---------
1AC power cord: RS814+ x1; RS814RP+ x2

4 Chapter 1: Before You Start
Synology RackStation at a Glance
No. Article Name Location Description
1) Power Indicator
Front
Panel
Displays power status of the RackStation. For more information, see
"Appendix B: LED Indicator Table".
2) Power Button
1.Press to power on the RackStation.
2.To power off the RackStation, press and hold until you hear a beep
sound and the power indicator starts blinking.
3) Alert Indicator Displays warnings regarding fan or temperature. For more information,
see "Appendix B: LED Indicator Table".
4) Disk Indicator Displays the status of internal drives. For more information, see "Appendix
B: LED Indicator Table".
5) Beep off Button Press to deactivate beep sound when malfunctions occur.
6) Status Indicator Displays the status of the system. For more information, see "Appendix B:
LED Indicator Table".
7) Drive Tray Install drives here.
8) Fan
Back
Panel
Disposes of excessive heat and cools the system. If a fan malfunctions,
the RackStation will emit a beeping sound.
9) Power Port Connect power cord here to supply power to your RackStation.
10) LAN Port Connect network cables here.
11) RESET Button
1.Press and hold until you hear a beep sound to restore the default IP
address, DNS server, and passwords for users belonging to the
administrators group.
2.Press and hold until you hear a beep sound, then press and hold again
until you hear three beep sounds to return the RackStation to “Not
Installed” status so that DiskStation Manager can be reinstalled.
12) USB 3.0 Port Connect external hard drives, USB printers, or other USB devices to the
Synology RackStation here.

5 Chapter 1: Before You Start
No.
Article Name
Location
Description
13) eSATA Port
Back
Panel
Connect external SATA drive or Synology Expansion Unit1
14)
to the
Synology RackStation.
Console Port For manufacturing use only.
15) Redundant Power LED Displays the status of redundant powers supplies, alerting the user of
power supply or fan failure.
16) Beep off Button Press to deactivate beep sound when malfunctions of redundant power
occur.
---------
1For more information about Synology Expansion Unit supported by your RackStation, please visit www.synology.com .

6 Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and from chemicals. Make sure the environment does not
experience abrupt changes in temperature or humidity.
Place the product right side up at all times.
Do not place near any liquids.
Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or
aerosol cleaners.
To prevent the unit from falling over, do not place on carts or any unstable surfaces.
The power cord must plug in to the correct supply voltage. Make sure that the supplied AC
voltage is correct and stable.
To remove all electrical current from the device, ensure that all power cords are disconnected
from the power source.
Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries
appropriately.

7
Chapter
2
Chapter 2: Hardware Setup
Tools and Parts for Drive Installation
A screwdriver
At least one 3.5” or 2.5” SATA drive (Please visit www.synology.com for compatible drive models.)
Warning: If you install a drive that contains data, the system will format the drive and erase all data. If you need the
data in the future, please back it up before installation.
Install Drives
1 Pull the drive tray handle in the direction as indicated below to remove the drive tray.
2 Load drives in the drive trays:
For 3.5" drives:Place the drive in the drive tray. Turn the tray upside down and tighten screws into the four
spots indicated below to secure the drive.
For 2.5" drives:Place the drive in the drive tray. Turn the tray upside down and tighten screws into the four
spots indicated below to secure the drive.

8 Chapter 2: Hardware Setup
3 Insert the loaded drive tray into the empty hard drive bay.
Important: Make sure the drive tray is completely inserted. Otherwise, the drive might not function properly.
4 Push the handle inward to secure the drive tray.
5 Insert the drive tray key into the drive tray lock, turn the key clockwise to lock the handle of the drive tray, and
then remove the key.
6 Repeat the steps above to install all prepared drives.
7 Fix the two rack mount kits on both sides with the nuts provided.
8 Drives are numbered as shown below.
Note: If you want to create a RAID volume, we recommended all installed drives be the same size in order to
optimize drive capacity usage.

9 Chapter 2: Hardware Setup
Add a RAM Module on RackStation
Synology offers RAM modules which allow you to expand the memory capacity of your RackStation. To install,
check, or remove your RAM module, please follow the steps below.
Install a RAM Module
1 Shut down the RackStation and disconnect all connected cables to prevent any possible damage.
2 Unscrew the two knobs that secure the back panel. Pull out the panel to reveal the circuit board.
Important: When you pull out the panel, you expose sensitive internal components. Avoid touching anything other
than the memory assembly when you remove or add memory.
3 To insert the new memory module, follow the steps below:
a Align the notch on the gold edge of the module with the notch in the memory slot.
b Tilt the card and push the memory into the slot. Make sure the module is pushed in all the way.
c Use two fingers to apply firm, even pressure and push the memory module downward. You should hear a
click when the memory is inserted correctly.
Important: Hold the memory module by its edges, and do not touch the gold connectors.

10 Chapter 2: Hardware Setup
4 Return the board into the RackStation:
a Identify the rail within the RackStation.
b Place the circuit board within the rail and push the board all the way in.
c Tighten the two knobs you unscrewed in step 2.
Confirm New Memory is Recognized
After installing a new memory module in the RackStation, we recommended checking whether or not the system
recognizes the new memory.
To check the memory of the RackStation:
1 Start up your RackStation. (See “Start up the RackStation” for more information.)
2 Install DiskStation Manager (DSM). (See “Chapter 3: Install DSM on RackStation” for more information.)
3 Log in to DSM with an account belonging to the administrators group.
4 Check Total Physical Memory at Main Menu > System Information.
If the RackStation does not recognize the memory or does not start up correctly, please make sure the memory
was correctly installed.
RS814+
4096 MB
RackStation