Synology RackStation RS3617xs User manual

Synology RackStation RS3617xs
Quick Installation Guide

Table of Contents
Chapter 1: Before You Start
Package Contents 3
Synology RackStation at a Glance 4
Safety Instructions 5
Chapter 2: Hardware Setup
Tools and Parts for Drive Installation 6
Install Drives 6
Add a RAM Module on RackStation 8
Add a Network Interface Card to RackStation 11
Replace System Fan 13
Start Up Your RackStation 15
Chapter 3: Install DSM on RackStation
Install DSM with Web Assistant 17
Learn More 17
Appedix A: Specications
Appedix B: LED Indicator Table
Synology_QIG_RS3617xs_20160321
2

Thank you for purchasing this Synology product! Before setting up your new RackStation, please check the
package contents to verify that you have received the items below. Also, make sure to read the safety instructions
carefully to avoid harming yourself or damaging your RackStation.
Note: All images below are for illustrative purposes only, and may differ from the actual product.
Package Contents
Main unit x 1 AC power cord x 1
Screws for 2.5” drives x 52
Screws for 3.5” drives x 52
Before You Start 1
Chapter
3
3

4Chapter 1: Before You Start
Synology RackStation at a Glance
No. Article Name Location Description
1 Power Button and
Indicator
Front Panel
1. Press to power on the RackStation.
2. To power off the RackStation, press and hold until you hear a beep
sound and the Power LED starts blinking.
2 Status Indicator Displays the status of the system. For more information, see "Appendix B:
LED Indicator Table".
3 Alert Indicator Displays warnings regarding fan or temperature. For more information,
see "Appendix B: LED Indicator Table".
4 Beep Off Button Press to deactivate the beeping sound that is emitted when a malfunction
occurs.
5 Drive Status Indicator Displays the status of drives. For more information, see "Appendix B:
LED Indicator Table".
6 Drive Tray Install drives (hard disk drives or solid state drives) here.
7 Power Port
Back Panel
Connect power cord here to supply power to your RackStation.
8 Power Supply On/Off
Switch Press to turn on/off the power supply.
9 PSU Fan Disposes of excess heat and cools the PSU.
10 Console Port This port is used for manufacturing use only.
11 USB 2.0 Port Connect external drives, or other USB devices to the RackStation here.
12 USB 3.0 Port Connect external drives, or other USB devices to the RackStation here.
13 LAN Port Connect RJ-45 network cables here.
14 RESET Button
1. Press and hold until you hear a beep sound to restore the default IP
address, DNS server, and password for the admin account.
2. Press and hold until you hear a beep sound, then press and hold
again until you hear three beep sounds to return the RackStation
to "Not Installed" status so that DiskStation Manager (DSM) can be
reinstalled.
15 Expansion Port Connect Synology Expansion Units1 to your Synology RackStation.
16 PCI Express Expansion
Slot Supports two PCIe x82add-on network interface cards.
1For more information about Synology Expansion Unit supported by your RackStation, please visit www.synology.com.
2White at x8 mode and black at x4 mode.

5Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and away from chemicals. Make sure the environment does not
experience abrupt changes in temperature or humidity.
Place the product right side up at all times.
Do not place near any liquids.
Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or
aerosol cleaners.
To prevent the unit from falling over, do not place on carts or any unstable surfaces.
The power cord must plug in to the correct supply voltage. Make sure that the supplied AC voltage is
correct and stable.
To remove all electrical current from the device, ensure that all power cords are disconnected from
the power source.
Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries appropriately.

Tools and Parts for Drive Installation
• A screwdriver
• At least one 3.5” or 2.5” SATA drive (please visit www.synology.com for compatible drive models.)
Warning: If you install a drive that contains data, the system will format the drive and erase all existing data. Please
back up any important data before installation.
Install Drives
1 Find the small button located on the drive tray handle. Press the button down and pull the drive try handle out
as illustrated below.
2 Load drives in the drive trays:
• For 3.5” drives: Place the drive in the drive tray. Turn the tray upside down and tighten screws into the four
spots indicated below to secure the drive.
• For 2.5” drives: Place the drive in the drive tray. Turn the tray upside down and tighten screws into the four
spots indicated below to secure the drive.
Hardware Setup
6
2
Chapter

7Chapter 2: Hardware Setup
3 Insert the loaded drive tray into the empty hard drive bay.
Important: Make sure the drive tray is completely inserted. Otherwise, the drive might not function properly.
4 Push the handle inward to secure the drive tray.
5 Repeat the steps above to install all prepared drives.
6 Drives are numbered as shown below.
Note: If you want to create a RAID volume, we recommend all installed drives be the same size in order to optimize
drive capacity usage.

8Chapter 2: Hardware Setup
Add a RAM Module on RackStation
Synology offers RAM modules which allow you to expand the memory capacity of your RackStation. To install,
check, or remove your RAM module, please follow the steps below.
To install a RAM module:
1 Shut down the RackStation and disconnect all connected cables to prevent any possible damage.
Important: Before installing the RAM module, please wait for at least 30 seconds after detaching the power
cord(s) from the RackStation to ensure complete discharge. Also, please remove any static electricity before
installation by touching water pipes, a metal conduit, or another person to get rid of excess charge and avoid
damaging the motherboard, peripherals, and other components.
2 Slide the latches shown below to release the fan cover.
3 Lift and remove the fan cover.

9Chapter 2: Hardware Setup
4 To remove the screws securing the top cover, follow the steps below:
a Remove the two screws illustrated below.
b Remove the two screws located on the back. Then slide the top cover in the direction indicated below and
lift.
c Remove the screws of the securing bracket and remove the securing bracket to reveal the RAM slots.
Important: Removing the cover will expose sensitive internal components to possible harm. Please avoid touching
any other components when adding or removing memory.

10 Chapter 2: Hardware Setup
5 To insert the new memory module, follow the steps below:
a Release the ejectors on the memory slot by pushing them outwards.
b Align the notch on the gold edge of the module with the notch in the memory slot.
c Use two ngers to apply rm, even pressure and push the memory module downward.
d When the memory is inserted correctly, the ejectors will snap into place.
6 Replace the top cover, slide it into place, and tighten all screws.