System air SAVEWALL HRV NEXT User manual

1
Installation manual
SAVEWALL HRV NEXT
G
Fig.1
SAVEWALL HRV NEXT is a single alternate flow decentralized (single point) residential heat recovery unit, also called
«push&pull» unit, designed to ensure adequate ventilation in enclosed environments without energy losses.
It is recommended that two units are installed in a pair: when one unit is pulling, the other is pushing.
The pair of units can be installed in the same room or in different rooms (i.e. living-room and bedroom). The unit is suitable
for installation on an outside wall.
Read this manual carefully before using the product and keep it in a safe
place for reference.
This product was constructed up to standard and in compliance with
regulations relating to electrical equipment and must be installed by
technically qualified personnel.
The manufacturer assumes no responsibility for damage to persons or
property resulting from failure to observe the regulations contained in this
booklet.
PRECAUTIONS FOR INSTALLATION, USE AND MAINTENANCE
•Thedeviceshouldnotbeusedforapplicationsotherthanthosespeciedinthismanual.
•Afterremovingtheproductfromitspackaging,verifyitscondition.Incaseofdoubt,contactaqualiedtechnician.Donot
leave packaging within the reach of small children or people with disabilities.
•Donottouchtheappliancewithwetordamphands/feet.
•Thisappliancecanbeusedbychildrenagedfrom8yearsandaboveandpersonswithreducedphysical,sensoryor
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without supervision.
•Donotusetheproductinthepresenceofinammablevapours,suchasalcohol,insecticides,gasoline,etc.
•If any abnormalities in operation are detected, disconnect the device from the mains supply and contact a qualied
technician immediately. Use original spare parts only for repairs.
•Theelectricalsystemtowhichthedeviceisconnectedmustcomplywithregulations.
•Beforeconnectingtheproducttothepowersupplyorthepoweroutlet,ensurethat:
- the data plate (voltage and frequency) correspond to those of the electrical mains
 -theelectricalpowersupply/socketisadequateformaximumdevicepower.Ifnot,contactaqualiedtechnician.
•Thedeviceshouldnotbeusedasanactivatorforwaterheaters,stoves,etc.,norshoulditdischargeintohotair/fumevent
ducts deriving from any type of combustion unit. It must expel air outside via its own special duct.
•Operatingtemperature:-20°Cupto+50°C.
•Thedeviceisdesignedtoextractcleanaironly,i.e.withoutgrease,soot,chemicalorcorrosiveagents,orammableor
explosive mixtures.
•Donotleavethedeviceexposedtoatmosphericagents(rain,sun,snow,etc.).
•Donotimmersethedeviceoritspartsinwaterorotherliquids.
•Turnoffthemainswitchwheneveramalfunctionisdetectedorwhencleaning.
•Forinstallationanomnipolarswitchshouldbeincorporatedinthexedwiring,inaccordancewiththewiringregulations,to
provide a full disconnection under overvoltage category III conditions (contact opening distance equal to or greater than 3mm).
•Ifthesupplycordisdamaged,itmustbereplacedbythemanufacturer,itsserviceagentorsimilarlyqualiedpersonsin
order to avoid a hazard.
•Donotobstructthefanorexhaustgrilletoensureoptimumairpassage.
•Ensureadequateairreturn/dischargeinto/fromtheroomincompliancewithexistingregulationsinordertoensureproper
device operation.
•Iftheenvironmentinwhichtheproductisinstalledalsohousesafuel-operatingdevice(waterheater,methanestoveetc.,
that is not a “sealed chamber” type), it is essential to ensure adequate air intake, to ensure good combustion and proper
equipment operation.
INTRODUCTION
The unit should operate continuously, and only stopped for maintenance or service.
When heat exchange is not useful (for example in mid-seasons when indoor and outdoor temperatures are similar), or
when heat exchange is not recommended (for example with the option “summer free cooling”), it is recommended to set
theunitin“extract-only”or“intake-only”modeandNOTtoswitchitoff.

2
•Designfrontcover(A)removableforcleaningwithouttheuseoftools.
•Innerventilationunit(B)andwallsupportbase(D)madeofhighquality,impactandUV-resistantABS,colourRAL9010.
•Integrated multi-colour led (C ) to obtain a visual feedback of the unit status.
•Smart humidity control.
•Integral temperature sensor for the automatic management of the inversion time (comfort mode)
•Automatic anti-frost protection to prevent frost building up on the heat exchanger.
•Wallsupportbase(D)providedwithamagnet“coupling/uncoupling”systemwhichallowstheventilationunittoberemoved
from its base during maintenance.
•Back-uptouchbutton(E)atthesideoftheventilationunit
•Unique design winglet-type impeller, providing enhanced aerodynamic properties, low noise and increased efficiency.
•High efficient reversible EC motor with integral thermal protection, mounted on sealed for life high quality ball bearings.
Designedforcontinuousreversiblerunning.
•Telescopicpipe(F)adaptabletothewallthickness.
•Antimortar cap designed to be used also as template during the installation of the wall support base
•Regenerative heat exchanger with ceramic core (G) with high thermal efficiency, equipped with washable anti-dust filters (H).
•Externalgrille(I)madeofhighquality,impactandUV-resistantABS,colourRAL9010,withanti-insectnetandwaterdrip
guard.
•Infra-redremotecontrollerwithtouchtechnology,LCDdisplayandwallbasesuppliedasstandard.MadefromABS,RAL
9010.
•The unit is double insulated: no earth connection is required.
•No need of condensation drainage system
•IPX4 degree of protection.
•Powersupply220Vto240V~50Hz.
TECHNICAL SPECIFICATIONS
FCBAE D GH
HI J
OPERATION
FILTER RESET BUTTON
MODE BUTTON
MODE ICON
FILTER RESET ICON
AIR FLOW DIRECTION ICON
SPEED ICON
BOOST ICON
SPEED BUTTONS
AIRFLOW DIRECTION BUTTON
BOOST BUTTON
REMOTE CONTROLLER
SPEED ICON
OFF BUTTON
KL
Fig.2

3
VENTILATION UNIT
When switched on the unit emits a long acoustic signal.
ThroughtheIRcontrollerthefollowingfunctionalitiescanbeactivated/deactivated.Whenonesettingistransferredtotheunit,
ashortacousticsignalisemittedandagreenledashes.
The unit is supplied with an infrared remote controller (K) as standard, as well as its support base (L) which can be wall
mounted. A magnet keeps the controller attached to the base.
ThecontrollerisequippedwithanLCDdisplaytovisualisethesettingtobetransferredtotheunit;anytimeatouchbuttonis
pressed,thesettingshownontheLCDdisplayistransferredtotheunit.TheIRreceiver(Jg.2)isplacedontheleftsideof
the ventilation unit: it is recommended to point the controller towards the receiver when any setting needs to be transfered.
Oneremotecontrollercancontrolmoreunits.
To activate the remote controller it is necessary to insert two AAA type batteries (not supplied).
external grille - installation
Ø5x40mm
5mm
cambio batterie telecomando
FUNCTIONALITY DESCRIPTION CONTROLLER
BUTTON ICON LED ACOUSTIC SIGNAL
Airflow direction
Alternate Theunitrunsinextract/intakeattheselectedspeed:theinversiontimeis
automaticallydenedthankstotheintegreltemperaturesensor. green short
Extract The unit runs in extract only at the selected speed. green short
Intake The unit runs in intake only at the selected speed. green short
Mode (active only if the airflow direction is set on alternate)
Comfort
Optimisation of the acoustic and thermal comfort. The inversion time
varies automatically from 40÷120 seconds, thanks to the integrel
temperaturesensor.Thersttimecycleisof120seconds,thenitvaries
automatically according to the detected temperature conditions.
green short
Efciency Optimisationofthethermalefciency.Theinversiontimeisxedatabout
70seconds. green short
Continuous running speed
Speed1:20m3/h green short
Speed2:30m3/h green short
Speed3:40m3/h green short
Speed4:50m3/h green short
Speed5:60m3/h green short
Off position
Pressing the button for 3 seconds, the units switches off, emitting a
long acoustic signal. To re-activate the unit, press any button. red long
BOOST speed
The unit runs at speed 5 (maximum) for 15 minutes, in extract only;
thenitreturnstothepreviouslyselectedmode/speed.TheBOOSTspeed
cannotbeactivatedifthecontrollerisOFF.
xedblue short
Free cooling
The unit runs in “extract only” or “intake only” to avoid heat recovery
when not needed. green short
COMFORT
EFFICIENCY
OFF
oppure
―+
―+
―+
―+
―+
―
―

4
Filter reset
Every3monthsayellowwarningledswitcheson(xedlight)toindicate
thattheltershavetobemaintained.Pressthededicatedbuttonfor5
seconds to reset the timing.
green short
Smart humidity control
When the humidity sensor detects a quick variation of the Relative
Humidity level, the running speed automatically increases to the next
higherspeed.After10minutesfromthelastquickRHvariation,theunit
returns running at the selected speed.The smart humidity control is active
iftheairowdirectionissetonalternateorextractonly:ifspeed5has
been selected, no speed increase happens. To disable this functionality,
pressthebuttonfor5seconds:onthetopsideoftheLCDdisplay
the symbol is shown.
ashingblue
Antifrost
This functionality prevents frost building up on the heat exchanger due
to extremely cold air. When it is activated, the unit runs in extract only at
speed1,for30minutes.
xedred
Acoustic signal
Any time a setting is transferred from the controller to the unit, a short
acoustic signal is emitted. This can be deactivated by pressing the cgfgf
buttonfor7seconds,afterwhenagreenledashestoindicatethatthe
acoustic signal is off. To reactivate the acoustic signal repeat the same
operation for 7 seconds until the led becomes green and an acoustic signal
is emitted.
green short
FILTER
RESET
BACKUPBUTTON
Incasetheremotecontrollergetslostorthebatteriesaredead,speeds1,3andOFFpositioncanbeselectedfromtheon
boardtouchbutton(C).Theairowdirectionisalwaysalternateandtheoperationmode(eithercomfortorefciency)isthe
last selected from the remote controller.
SYNCHRONISATIONOFANUMBEROFUNITS
Itispossibletosynchronizedupto10unitscontemporaneously,throughwire(2poletwistedpairtype,max30mlength)
sotohavemodeandinversiontimesynchronized.Whentheunitisswitchedonforthersttime,therotationdirectionof
eachunit(clockwiseoranti-clockwise)isautomaticallyestablished.Otherfunctionalitieslikespeed,smarthumiditycontrol
and boost , continue to be controlled independently on each single unit.
Wiringdiagramasperg.16B.
Maintenancecanbecarriedoutbytheuserasindicatedinpage12.
MAINTENANCE
SPEED LED COLOUR ACOUSTIC SIGNAL
speed1 single green led short, single
speed 3 double green led short, double
OFF red led long

5
218 76
DIMENSIONS (mm)
G
ØH
q ABC
G
ØH
q ABC
G
ØH
q ABC
G
ØH
q ABC
300÷560
270÷510
164
q
164
q
108 O mm
Ø158
INSTALLATION
1°÷2°
contenuto imballo modello Quantum NEXT
1° ÷ 2°
indoor outdoor
colorare filtro e strisce mousse
OUTDOOR
INDOOR
1
contenuto imballo modello Quantum NEXT
1° ÷ 2°
indoor outdoor
colorare filtro e strisce mousse
contenuto imballo modello Quantum NEXT
1° ÷ 2°
indoor outdoor
colorare filtro e strisce mousse
contenuto imballo modello Quantum NEXT
1° ÷ 2°
indoor outdoor
colorare filtro e strisce mousse
sostituire possibilmente solo il tubo nell'immagine "contenuto imballo"
fig.1
23
218
Questo documento è protetto dalle leggi v igenti in materia di privacy e copyright. Nè è vietata la copia, la diffusione senza autorizzazione di Aerauliqa srl This document i s protected by privacy and copyrigh t laws. No part of this document m ay be reproduced, adapted, trasmit ted or disclosed without the specific writte nc onsent of Aerauliqa srl. All right are reserved.
aera aqi lu
AERAULIQA SRL Sede legale / Registered office: via Corsica 10, 25125 Brescia Sede operativa / Warehouse-offices: via M.Calderara 39 / 41 25018 Montichiari (Bs) Tel: [phone] Fax: [phone] C.F. e P.IVA 03369930981 - REA BS-528635 www.aerauliqa.it
Descrizione/Description: Materiale/Material: Data/Date: Firma/Signature:
Terraroli Stefano15/12/2017-
Telecomando Quantum Next
dimensioni
Rev. Descrizione/Description Data/Date Firma/Sign.
-- - TS
\Progetti\..\
ARCHIVIO CA D:
AQD.01178.00 003036
1:1
No. Dis/No. Drawing: Codice/Code: Scala/Scale:
-
Peso/Weight:
124
44 26,5
117,5
39 23
39 23
117,5
Questo documento è pro tetto dalle leggi vigenti in mater ia di privacy e copyright. Nè è vietata l a copia, la diffusione senza autorizzazione di Aerauliqa srl This document i s protected by privacy and copyrigh t laws. No part of this document m ay be reproduced, adapted, trasmit ted or disclosed without the specific writte nc onsent of Aerauliqa srl. All right are reserved.
aera aqi lu
AERAULIQA SRL Sede legale / Registered office: via Corsica 10, 25125 Brescia Sede operativa / Warehouse-offices: via M.Calderara 39 / 41 25018 Montichiari (Bs) Tel: [phone] Fax: [phone] C.F. e P.IVA 03369930981 - REA BS-528635 www.aerauliqa.it
Descrizione/Description: Materiale/Material: Data/Date: Firma/Signature:
Terraroli Stefano15/12/2017-
Telecomando Quantum Next
dimensioni
Rev. Descrizione/Description Data/Date Firma/Sign.
-- - TS
\Progetti\..\
ARCHIVIO CA D:
AQD.01178.00 003036
1:1
No. Dis/No. Drawing: Codice/Code: Scala/Scale:
-
Peso/Weight:
124
44 26,5
117,5
39 23
44 26,5
124
contenuto imballo modello Quantum NEXT (sostituisce immagine 1 )
10 x
sostituisce la nr°4 sostituisce la nr°6 sostituisce la nr°7
(e la 9 aggiungendo
le relative frecce)
contenuto imballo modello Quantum NEXT (sostituisce immagine 1 )
10 x
sostituisce la nr°4 sostituisce la nr°6 sostituisce la nr°7
(e la 9 aggiungendo
le relative frecce)
min. 158mm

6
6
insulation foam
5
4
7
RECESSED CABLE ENTRY
H03VV-F ; H05VV-F
2 X 0,5 ÷ 1,5 mm2
8
aggiungere freccia
x aprire il coperchietto
aggiungere freccia
x togliere passacavo apertura presfondabile
aggiungere freccia
x chiudere il coperchietto
colorare filtro e strisce mousse
aggiungere frecce
inserimento scambiatore
INIZIO INSTALLAZIONE
SOTTOTRACCIA
Ø 5 mm
Ø 5 mm
Ø 5 mm
Ø 5 mm
COLLEGAMENTI
ELETTRICI
aggiungere freccia
x aprire il coperchietto
aggiungere freccia
x togliere passacavo apertura presfondabile
aggiungere freccia
x chiudere il coperchietto
colorare filtro e strisce mousse
aggiungere frecce
inserimento scambiatore
INIZIO INSTALLAZIONE
SOTTOTRACCIA
Ø 5 mm
Ø 5 mm
Ø 5 mm
Ø 5 mm
COLLEGAMENTI
ELETTRICI
9
aggiungere freccia
x aprire il coperchietto
aggiungere freccia
x togliere passacavo apertura presfondabile
aggiungere freccia
x chiudere il coperchietto
colorare filtro e strisce mousse
aggiungere frecce
inserimento scambiatore
INIZIO INSTALLAZIONE
SOTTOTRACCIA
Ø 5 mm
Ø 5 mm
Ø 5 mm
Ø 5 mm
COLLEGAMENTI
ELETTRICI
aggiungere freccia
x aprire il coperchietto
aggiungere freccia
x togliere passacavo apertura presfondabile
aggiungere freccia
x chiudere il coperchietto
colorare filtro e strisce mousse
aggiungere frecce
inserimento scambiatore
INIZIO INSTALLAZIONE
SOTTOTRACCIA
Ø 5 mm
Ø 5 mm
Ø 5 mm
Ø 5 mm
COLLEGAMENTI
ELETTRICI
10

7
12
11
14
13
15
L
N
R
R
B
B
L
N
L
N
16B
4xØ5mm
L
N
16A

8
17
19
20
21
CLICK
aggiungere ai lati del prodotto
simboli di "avvenuto aggancio"
ON
OFF
aggiungere frecce
x install parte ventilante
115 mm
colorare filtro
22
18
ON
OFF

9
23
24
INIZIO INSTALLAZIONE
SUPERFICIE
Ø 5 mm
Ø 5 mm
Ø 5 mm
Ø 5 mm
aggiungere freccia
x aprire il coperchietto
aggiungere freccia
x togliere passacavo
apertura presfondabile
Ø 10 mm
aggiungere freccia
x inserimento passacavo
aggiungere freccia
x svitare viti fermacavo aggiungere freccia
x avvitare viti fermacavo aggiungere freccia
x chiudere il coperchietto
COLLEGAMENTI
ELETTRICI
27
SURFACE CABLE (for one unit wiring)
H03VV-F ; H05VV-F
2 X 0,5 ÷ 1,5 mm2
25
aggiungere freccia
x aprire il coperchietto
aggiungere freccia
x togliere passacavo apertura presfondabile
aggiungere freccia
x chiudere il coperchietto
colorare filtro e strisce mousse
aggiungere frecce
inserimento scambiatore
INIZIO INSTALLAZIONE
SOTTOTRACCIA
Ø 5 mm
Ø 5 mm
Ø 5 mm
Ø 5 mm
COLLEGAMENTI
ELETTRICI
aggiungere freccia
x aprire il coperchietto
aggiungere freccia
x togliere passacavo apertura presfondabile
aggiungere freccia
x chiudere il coperchietto
colorare filtro e strisce mousse
aggiungere frecce
inserimento scambiatore
INIZIO INSTALLAZIONE
SOTTOTRACCIA
Ø 5 mm
Ø 5 mm
Ø 5 mm
Ø 5 mm
COLLEGAMENTI
ELETTRICI
26
aggiungere freccia
x aprire il coperchietto
aggiungere freccia
x togliere passacavo apertura presfondabile
aggiungere freccia
x chiudere il coperchietto
colorare filtro e strisce mousse
aggiungere frecce
inserimento scambiatore
INIZIO INSTALLAZIONE
SOTTOTRACCIA
Ø 5 mm
Ø 5 mm
Ø 5 mm
Ø 5 mm
COLLEGAMENTI
ELETTRICI
Ø10mm
29
28
4xØ5mm

10
INIZIO INSTALLAZIONE
SUPERFICIE
Ø 5 mm
Ø 5 mm
Ø 5 mm
Ø 5 mm
aggiungere freccia
x aprire il coperchietto
aggiungere freccia
x togliere passacavo
apertura presfondabile
Ø 10 mm
aggiungere freccia
x inserimento passacavo
aggiungere freccia
x svitare viti fermacavo aggiungere freccia
x avvitare viti fermacavo aggiungere freccia
x chiudere il coperchietto
COLLEGAMENTI
ELETTRICI
L
N
30 31
32
34 35
36 37
33

11
aggiungere ai lati del prodotto
simboli di "avvenuto aggancio"
ON
OFF
aggiungere frecce
x install parte ventilante
115 mm
aggiungere frecce
x aggancio telecomando dalla base
Ø 5 mm
aggiungere frecce
x distacco telecomando dalla base
aggiungere scritte
ALTO - TOP
colorare filtro e strisce mousse
frecce inserimento scambiatore
40 41
42 43
CLICK
44 45
REMOTE CONTROLLER WALL MOUNTING
39
Ø5mm
38

12
EXTERNAL GRILLE
Ø 5x40mm
3-5mm 47
46
48
MAINTENANCE
colorare filtro e strisce mousse
aggiungere frecce per estrazione scambiatore
colorare filtro e strisce mousse
colorare filtro e strisce mousse
aggiungere frecce per inserimento scambiatore
colorare filtro e strisce mousse
aggiungere frecce
x distacco parte ventilante
MANUTENZIONE (COMUNE A TUTTE E DUE LE INSTALLAZIONI)
aggiungere frecce
x distacco coprifrontale
50
51 52
49

13
colorare filtro e strisce mousse
aggiungere frecce per estrazione scambiatore
colorare filtro e strisce mousse
colorare filtro e strisce mousse
aggiungere frecce per inserimento scambiatore
colorare filtro e strisce mousse
aggiungere frecce
x distacco parte ventilante
MANUTENZIONE (COMUNE A TUTTE E DUE LE INSTALLAZIONI)
aggiungere frecce
x distacco coprifrontale
54
55 56
53
60
59
58
57

14
62
64
63
CLICK
65
FILTER CLEANING FILTER REPLACEMENT HEAT EXCHANGER CLEANING
DATE
DATE
DATE
DATE
DATE
DATE
DATE
DATE
MAINTENANCE/CLEANING REGISTER
61

15
ANOMALY POSSIBLE CAUSE SOLUTION
NoiconshownonthecontrollerLCD
display
Batteriesaredead Change the batteries
Batteriesarenotpresent Check that batteries are in there
Batteriesarewronglypositioned Position the batteries correctly
The unit does not execute the
command sent from the remote control
Lack of communication between the unit and the
remote controller
Go closer to the unit, pointing the controller to the
receiver on the left side of the unit
The unit does not operate There is no voltage Check that the unit is correctly wired to the main supply
Ventilation unit does not couple correctly with the
support base
Check that the coupling is properly done
The unit operates at the maximum
speed
TheBoostfunctionalityisactivated,onthedisplay
the icon is shown
Waituntiltheboosttimingends(15minutes)
or deactivate the boost function pressing the
button.
Unit speed suddenly increases The smart humidity control is activated Waituntilthesmarthumiditycontrolphaseends(10
minutes) or deactivate the humidity control function
pressingthebuttonfor5seconds.
Fixedyellowled Dirtyters Filtersmaintenance/replacementisneeded:reset
lteroperationhastobedone(seepage4)
Fixedredled Antifrost protection is activated Waituntiltheantifrostphaseends(30minutes)
Fixedblueled Boostisactivated Waituntiltheboosttimingends(15minutes)
or deactivate the boost function pressing the
button.
Flashingblueled Smart humidity control is activated Waitunitlthehumiditycontrolphaseends(10
minutes)
Fixedpurpleled Ventilation unit does not couple correctly with the
support base Check that the coupling is properly done
Acoustic signal to disable - Press the button for 7 seconds: a green led
ashes.
TROUBLE SHOOTING
DISPOSAL AND RECYCLING
Information on disposal of units at the end of life.
ThisproductcomplieswithEUDirective2002/96/EC.
The symbol of the crossed-out dustbin indicates that this product must be collected separately from
other waste at the end of its life. The user must, therefore, dispose of the product in question at
suitable electronic and electro-technical waste disposal collection centres, or else send the product
back to the retailer when purchasing a new, equivalent type device.
Separate collection of decommissioned equipment for recycling, treatment and environmentally
compatible disposal helps to prevent negative effects on the environment and on health and promotes
the recycling of the materials that make up the equipment.
Improper disposal of the product by the user may result in administrative sanctions as provided by
law.
2014/35/UE LowVoltage Directive (LVD) and 2014/30/UE Electromagnetic Compatibility (EMC), in conformity with the
following standards:
Electrical Safety: EN60335-1(2012)+A11+A13;EN60335-2-80(2003)+A1+A2.
Electromagnetic Compatibility: EN55014-1(2017);EN55014-2(2015);EN61000-3-2(2014);EN61000-3-3(2013).
STANDARD CONFORMITY

16
a) Mark - SYSTEMAIR
b) Model - SAVEWALL HRV NEXT
c) SEC class - A
c1) SEC warm climates kWh/m2.a -18,1
c2) SEC average climates kWh/m2.a -41,7
c3) SEC cold climates kWh/m2.a -83
Energy label -Yes
d) Unit typology -Residenal - bidireconal
e) Type of drive - Mul-speed drive
f) Type of Heat Recovery System - Heat recovery
g) Thermal eciency of heat recovery % 74
h) Maximum ow rate m3/h 60
i) Electric power input at maximum ow rate W 6
j) Sound power level (LWA)dBA 40
k) Reference ow rate m3/h 41
l) Reference pressure dierence Pa 10
m) Specic power input (SPI) W/m3/h 0,08
n1) Control factor - 0,65
n2) Control typology - Local demand control
o1) Maximum internal leakage rate % N/A
o2) Maximum external leakage rate % 1
p1) Internal mixing rate %N/A
p2) External mixing rate % N/A
q) Visual lter warning -N/A
r) Instrucons to install regulated grilles -N/A
s) Internet address for pre/disassembly instrucons -www.systemair.gr
t) Airow sensivity to pressure variaons %N/A
u) Indoor/outdoor air ghtness m3/h 50
v1) AEC - Annual electricity consumpon - warm climates kWh 0,6
v2) AEC - Annual electricity consumpon - average climates kWh 0,6
v3) AEC - Annual electricity consumpon - cold climates kWh 0,6
w1) AHS - Annual heang saved - warm climates kWh 19,5
w2) AHS - Annual heang saved - average climates kWh 43,2
w3) Annual heang saved - cold climates kWh 84,4
ErP Directive - Regulations 1253/2014 - 1254/2014

17
NOTES

18
NOTES

19
NOTES

Systemair Hellas SA
Astrous13,Ilion,13121,Greece
Phone:00302105789766,Fax:00302105789768
www.systemair.gr
[e-mail]
004047-00-0618